mirror of https://github.com/ArduPilot/ardupilot
323 lines
9.9 KiB
Plaintext
323 lines
9.9 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
|
|
# USB setup
|
|
USB_VENDOR 0x2DAE # ONLY FOR USE BY HEX! NOBODY ELSE
|
|
USB_PRODUCT 0x1016
|
|
USB_STRING_MANUFACTURER "Hex/ProfiCNC"
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 140
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# with 2M flash we can afford to optimize for speed
|
|
env OPTIMIZE -O2
|
|
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
define HAL_STORAGE_SIZE 32768
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C2 I2C1
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 UART7 OTG2
|
|
|
|
# If the board has an IOMCU connected via a UART then this defines the
|
|
# UART to talk to that MCU. Leave it out for boards with no IOMCU.
|
|
|
|
# UART for IOMCU
|
|
IOMCU_UART USART6
|
|
|
|
# UART4 serial GPS
|
|
PA0 UART4_TX UART4
|
|
PA1 UART4_RX UART4 NODMA
|
|
|
|
PA2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
# Now the VDD sense pin. This is used to sense primary board voltage.
|
|
PA4 VDD_5V_SENS ADC1 SCALE(2)
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# This defines an output pin which will default to output HIGH. It is
|
|
# a pin that enables peripheral power on this board. It starts in the
|
|
# off state, then is pulled low to enable peripherals in
|
|
# peripheral_power_enable()
|
|
PA8 nVDD_5V_PERIPH_EN OUTPUT HIGH
|
|
|
|
# This is the pin that senses USB being connected. It is an input pin
|
|
# setup as OPENDRAIN.
|
|
PA9 VBUS INPUT OPENDRAIN
|
|
|
|
# Now we define the pins that USB is connected on.
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# These are the pins for SWD debugging with a STlinkv2 or black-magic probe.
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# PWM output for buzzer
|
|
PA15 TIM2_CH1 TIM2 GPIO(77) ALARM
|
|
|
|
# This defines a couple of general purpose outputs, mapped to GPIO
|
|
# numbers 1 and 2 for users.
|
|
PB0 EXTERN_GPIO1 OUTPUT GPIO(1)
|
|
PB1 EXTERN_GPIO2 OUTPUT GPIO(2)
|
|
|
|
# This defines some input pins, currently unused.
|
|
PB2 BOOT1 INPUT
|
|
PB3 FMU_SW0 INPUT
|
|
|
|
# This defines the pins for the 2nd CAN interface, if available.
|
|
PB6 CAN2_TX CAN2
|
|
PB12 CAN2_RX CAN2
|
|
|
|
# Now the first I2C bus. The pin speeds are automatically setup
|
|
# correctly, but can be overridden here if needed.
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# the 2nd I2C bus
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
|
|
# the 2nd SPI bus
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
# This input pin is used to detect that power is valid on USB.
|
|
PC0 VBUS_nVALID INPUT PULLUP
|
|
|
|
# This defines the CS pin for the magnetometer and first IMU. Note
|
|
# that CS pins are software controlled, and are not tied to a particular
|
|
# SPI bus.
|
|
PC1 MAG_CS CS
|
|
PC2 MPU_CS CS
|
|
|
|
# This defines more ADC inputs.
|
|
PC3 AUX_POWER ADC1 SCALE(1)
|
|
PC4 AUX_ADC2 ADC1 SCALE(1)
|
|
|
|
# And the analog input for airspeed (rarely used these days).
|
|
PC5 PRESSURE_SENS ADC1 SCALE(2)
|
|
|
|
# USART6 to IO
|
|
PC6 USART6_TX USART6
|
|
PC7 USART6_RX USART6
|
|
|
|
# Now setup the pins for the microSD card, if available.
|
|
PC8 SDMMC1_D0 SDMMC1
|
|
PC9 SDMMC1_D1 SDMMC1
|
|
PC10 SDMMC1_D2 SDMMC1
|
|
PC11 SDMMC1_D3 SDMMC1
|
|
PC12 SDMMC1_CK SDMMC1
|
|
PD2 SDMMC1_CMD SDMMC1
|
|
|
|
# More CS pins for more sensors. The labels for all CS pins need to
|
|
# match the SPI device table later in this file.
|
|
PC13 GYRO_EXT_CS CS
|
|
PC14 BARO_EXT_CS CS
|
|
PC15 ACCEL_EXT_CS CS
|
|
PD7 BARO_CS CS
|
|
PE4 MPU_EXT_CS CS
|
|
|
|
# the first CAN bus
|
|
PD0 CAN1_RX CAN1
|
|
PD1 CAN1_TX CAN1
|
|
|
|
# Another USART, this one for telem1. This one has RTS and CTS lines.
|
|
# USART2 serial2 telem1
|
|
PD3 USART2_CTS USART2
|
|
PD4 USART2_RTS USART2
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
|
|
# The telem2 USART, also with RTS/CTS available.
|
|
# USART3 serial3 telem2
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
PD11 USART3_CTS USART3
|
|
PD12 USART3_RTS USART3
|
|
|
|
# The CS pin for FRAM (ramtron). This one is marked as using
|
|
# SPEED_VERYLOW, which matches the HAL_PX4 setup.
|
|
PD10 FRAM_CS CS SPEED_VERYLOW
|
|
|
|
# Now we start defining some PWM pins. We also map these pins to GPIO
|
|
# values, so users can set BRD_PWM_COUNT to choose how many of the PWM
|
|
# outputs on the primary MCU are setup as PWM and how many as
|
|
# GPIOs. To match HAL_PX4 we number the GPIOs for the PWM outputs
|
|
# starting at 50.
|
|
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
|
|
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
|
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
|
|
# Pin for PWM Voltage Selection
|
|
PB4 PWM_VOLT_SEL OUTPUT HIGH GPIO(3)
|
|
|
|
# This is the invensense data-ready pin. We don't use it in the
|
|
# default driver.
|
|
PD15 MPU_DRDY INPUT
|
|
|
|
# the 2nd GPS UART
|
|
# UART8 serial4 GPS2
|
|
PE0 UART8_RX UART8
|
|
PE1 UART8_TX UART8 NODMA
|
|
|
|
# Now setup SPI bus4.
|
|
PE2 SPI4_SCK SPI4
|
|
PE5 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
# This is the pin to enable the sensors rail. It can be used to power
|
|
# cycle sensors to recover them in case there are problems with power on
|
|
# timing affecting sensor stability. We pull it LOW on startup, which
|
|
# means sensors off, then it is pulled HIGH in peripheral_power_enable()
|
|
PE3 VDD_3V3_SENSORS_EN OUTPUT LOW
|
|
|
|
# UART7 maps to uartF in the HAL (serial5 in SERIALn_ parameters).
|
|
PE7 UART7_RX UART7
|
|
PE8 UART7_TX UART7
|
|
|
|
# Define a LED, mapping it to GPIO(0). LOW will illuminate the LED
|
|
PE12 FMU_LED_AMBER OUTPUT HIGH OPENDRAIN GPIO(0)
|
|
|
|
# Power flag pins: these tell the MCU the status of the various power
|
|
# supplies that are available. The pin names need to exactly match the
|
|
# names used in AnalogIn.cpp.
|
|
PB5 VDD_BRICK_nVALID INPUT PULLUP
|
|
PB7 VDD_BRICK2_nVALID INPUT PULLUP
|
|
PE10 VDD_5V_HIPOWER_nOC INPUT PULLUP
|
|
PE15 VDD_5V_PERIPH_nOC INPUT PULLUP
|
|
|
|
SPIDEV ms5611 SPI1 DEVID3 BARO_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV ms5611_ext SPI4 DEVID2 BARO_EXT_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV mpu6000 SPI1 DEVID4 MPU_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV icm20608-am SPI1 DEVID2 ACCEL_EXT_CS MODE3 4*MHZ 8*MHZ
|
|
SPIDEV mpu9250 SPI1 DEVID4 MPU_CS MODE3 4*MHZ 8*MHZ
|
|
SPIDEV mpu9250_ext SPI4 DEVID1 MPU_EXT_CS MODE3 4*MHZ 8*MHZ
|
|
SPIDEV icm20948 SPI1 DEVID4 MPU_CS MODE3 4*MHZ 8*MHZ
|
|
SPIDEV icm20948_ext SPI4 DEVID1 MPU_EXT_CS MODE3 4*MHZ 8*MHZ
|
|
SPIDEV hmc5843 SPI1 DEVID5 MAG_CS MODE3 11*MHZ 11*MHZ
|
|
SPIDEV lsm9ds0_g SPI1 DEVID1 GYRO_EXT_CS MODE3 11*MHZ 11*MHZ
|
|
SPIDEV lsm9ds0_am SPI1 DEVID2 ACCEL_EXT_CS MODE3 11*MHZ 11*MHZ
|
|
SPIDEV lsm9ds0_ext_g SPI4 DEVID4 GYRO_EXT_CS MODE3 11*MHZ 11*MHZ
|
|
SPIDEV lsm9ds0_ext_am SPI4 DEVID3 ACCEL_EXT_CS MODE3 11*MHZ 11*MHZ
|
|
SPIDEV icm20602_ext SPI4 DEVID4 GYRO_EXT_CS MODE3 4*MHZ 8*MHZ
|
|
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
SPIDEV external0m0 SPI4 DEVID5 MPU_EXT_CS MODE0 2*MHZ 2*MHZ
|
|
SPIDEV external0m1 SPI4 DEVID5 MPU_EXT_CS MODE1 2*MHZ 2*MHZ
|
|
SPIDEV external0m2 SPI4 DEVID5 MPU_EXT_CS MODE2 2*MHZ 2*MHZ
|
|
SPIDEV external0m3 SPI4 DEVID5 MPU_EXT_CS MODE3 2*MHZ 2*MHZ
|
|
SPIDEV pixartPC15 SPI4 DEVID13 ACCEL_EXT_CS MODE3 2*MHZ 2*MHZ
|
|
|
|
# three IMUs, but allow for different variants. First two IMUs are
|
|
# isolated, 3rd isn't
|
|
IMU Invensense SPI:mpu9250_ext ROTATION_PITCH_180
|
|
|
|
# the 3 rotations for the LSM9DS0 driver are for the accel, the gyro
|
|
# and the H variant of the gyro
|
|
IMU LSM9DS0 SPI:lsm9ds0_ext_g SPI:lsm9ds0_ext_am ROTATION_ROLL_180_YAW_270 ROTATION_ROLL_180_YAW_90 ROTATION_ROLL_180_YAW_90
|
|
|
|
# 3rd non-isolated IMU
|
|
IMU Invensense SPI:mpu9250 ROTATION_YAW_270
|
|
|
|
# alternative IMU set for newer cubes
|
|
IMU Invensense SPI:icm20602_ext ROTATION_ROLL_180_YAW_270
|
|
IMU Invensensev2 SPI:icm20948_ext ROTATION_PITCH_180
|
|
IMU Invensensev2 SPI:icm20948 ROTATION_YAW_270
|
|
|
|
# Sensor Check alias for validating board type
|
|
CHECK_ICM20649 spi_check_register_inv2("icm20948", INV2REG_WHOAMI, INV2_WHOAMI_ICM20649)
|
|
CHECK_ICM20602_EXT spi_check_register("icm20602_ext", MPUREG_WHOAMI, MPU_WHOAMI_ICM20602)
|
|
CHECK_ICM20948_EXT spi_check_register_inv2("icm20948_ext", INV2REG_WHOAMI, INV2_WHOAMI_ICM20948)
|
|
CHECK_MS5611 check_ms5611("ms5611")
|
|
CHECK_MS5611_EXT check_ms5611("ms5611_ext")
|
|
|
|
# Sensor Check Macros to be used for validating board type
|
|
CHECK_IMU0_PRESENT $CHECK_ICM20602_EXT
|
|
CHECK_IMU1_PRESENT $CHECK_ICM20948_EXT
|
|
CHECK_IMU2_PRESENT $CHECK_ICM20649
|
|
CHECK_BARO0_PRESENT $CHECK_MS5611
|
|
CHECK_BARO1_PRESENT $CHECK_MS5611_EXT
|
|
|
|
BOARD_VALIDATE $CHECK_IMU0_PRESENT $CHECK_IMU1_PRESENT $CHECK_IMU2_PRESENT $CHECK_BARO0_PRESENT $CHECK_BARO1_PRESENT
|
|
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 7
|
|
|
|
# two baros
|
|
BARO MS56XX SPI:ms5611_ext
|
|
BARO MS56XX SPI:ms5611
|
|
|
|
# two compasses. First is in the LSM303D
|
|
COMPASS LSM303D SPI:lsm9ds0_ext_am ROTATION_YAW_270
|
|
# 2nd compass is part of the 2nd invensense IMU
|
|
COMPASS AK8963:probe_mpu9250 1 ROTATION_YAW_270
|
|
|
|
# compass as part of ICM20948 on newer cubes
|
|
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180_YAW_90
|
|
|
|
# offset the internal compass for EM impact of the IMU heater
|
|
# this is in sensor frame mGauss
|
|
define HAL_AK09916_HEATER_OFFSET Vector3f(30,10,235)
|
|
|
|
# also probe for external compasses
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
define HAL_CHIBIOS_ARCH_FMUV3 1
|
|
|
|
define BOARD_TYPE_DEFAULT 3
|
|
|
|
# Nnow some defines for logging and terrain data files.
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
# allow to have have a dedicated safety switch pin
|
|
define HAL_HAVE_SAFETY_SWITCH 1
|
|
|
|
# Enable RAMTROM parameter storage.
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# Setup the IMU heater
|
|
define HAL_HAVE_IMU_HEATER 1
|
|
define HAL_IMU_TEMP_DEFAULT 45
|
|
define HAL_IMUHEAT_P_DEFAULT 50
|
|
define HAL_IMUHEAT_I_DEFAULT 0.07
|
|
|
|
# Enable FAT filesystem support (needs a microSD defined via SDMMC).
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# Now setup the default battery pins driver analog pins and default
|
|
# scaling for the power brick.
|
|
define HAL_BATT_VOLT_PIN 14
|
|
define HAL_BATT_CURR_PIN 15
|
|
define HAL_BATT_VOLT_SCALE 10.1
|
|
define HAL_BATT_CURR_SCALE 17.0
|
|
define HAL_GPIO_PWM_VOLT_PIN 3
|
|
define HAL_GPIO_PWM_VOLT_3v3 1
|
|
|
|
# List of files to put in ROMFS. For fmuv3 we need an IO firmware so
|
|
# we can automatically update the IOMCU firmware on boot. The format
|
|
# is "ROMFS ROMFS-filename source-filename". Paths are relative to the
|
|
# ardupilot root.
|
|
ROMFS io_firmware.bin Tools/IO_Firmware/iofirmware_highpolh.bin
|
|
|
|
DMA_NOSHARE SPI1* SPI4* USART6*
|
|
|