mirror of https://github.com/ArduPilot/ardupilot
118 lines
2.2 KiB
Plaintext
118 lines
2.2 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# MCU class and specific type
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F412Rx
|
|
|
|
# default to all pins low to avoid ESD issues
|
|
DEFAULTGPIO OUTPUT LOW PULLDOWN
|
|
|
|
# bootloader starts firmware at 64k
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
# store parameters in pages 2 and 3
|
|
STORAGE_FLASH_PAGE 2
|
|
define HAL_STORAGE_SIZE 8192
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1085
|
|
|
|
# setup build for a peripheral firmware
|
|
env AP_PERIPH 1
|
|
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
define CH_CFG_ST_FREQUENCY 1000000
|
|
|
|
# assume 512k flash part
|
|
FLASH_SIZE_KB 512
|
|
|
|
STDOUT_SERIAL SD1
|
|
STDOUT_BAUDRATE 57600
|
|
|
|
# order of UARTs
|
|
SERIAL_ORDER USART1 EMPTY EMPTY USART2
|
|
|
|
# a LED to flash
|
|
PB0 LED OUTPUT LOW
|
|
|
|
# USART1 for debug
|
|
PB6 USART1_TX USART1 NODMA
|
|
PB7 USART1_RX USART1 NODMA
|
|
define DEFAULT_SERIAL0_BAUD 57600
|
|
|
|
# USART2 for GPS
|
|
PA2 USART2_TX USART2
|
|
PA3 USART2_RX USART2
|
|
|
|
# SWD debugging
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# one I2C bus
|
|
PA8 I2C3_SCL I2C3
|
|
PB4 I2C3_SDA I2C3
|
|
|
|
I2C_ORDER I2C3
|
|
|
|
# compass
|
|
COMPASS RM3100 I2C:0:0x20 false ROTATION_YAW_270
|
|
|
|
# safety LED, active low
|
|
PB5 SAFE_LED OUTPUT HIGH
|
|
define SAFE_LED_ON 0
|
|
|
|
define HAL_USE_ADC FALSE
|
|
define STM32_ADC_USE_ADC1 FALSE
|
|
define HAL_DISABLE_ADC_DRIVER TRUE
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
|
|
# avoid RCIN thread to save memory
|
|
define HAL_USE_RTC FALSE
|
|
|
|
define DMA_RESERVE_SIZE 0
|
|
|
|
# enable CAN support
|
|
PB8 CAN1_RX CAN1
|
|
PB9 CAN1_TX CAN1
|
|
PB1 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(70)
|
|
|
|
# sensor power enable
|
|
PA12 VDD_SENSOR_EN OUTPUT HIGH
|
|
|
|
# RTK reset
|
|
PA4 RTK_RESET_N OUTPUT HIGH
|
|
|
|
# PPS
|
|
PA7 PPS INPUT PULLUP
|
|
|
|
define HAL_DEVICE_THREAD_STACK 768
|
|
|
|
# we setup a small defaults.parm
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 256
|
|
|
|
define GPS_MAX_RECEIVERS 1
|
|
define GPS_MAX_INSTANCES 1
|
|
|
|
define HAL_PERIPH_ENABLE_GPS
|
|
define GPS_MOVING_BASELINE 1
|
|
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
define HAL_COMPASS_MAX_SENSORS 1
|
|
|
|
define AP_GPS_BACKEND_DEFAULT_ENABLED 0
|
|
define AP_GPS_NMEA_ENABLED 1
|
|
define AP_GPS_NMEA_UNICORE_ENABLED 1
|
|
|
|
define HAL_GPS1_TYPE_DEFAULT 25
|
|
|
|
# custom config once sensor is found
|
|
define AP_GPS_NMEA_CUSTOM_CONFIG_STRING "CONFIG COM1 230400 8 N 1"
|
|
|
|
# custom config for GPS probe
|
|
define NMEA_UNICORE_SETUP "CONFIG COM1 230400 8 n 1\r\nGPGGA 0.2\r\n"
|