mirror of https://github.com/ArduPilot/ardupilot
268 lines
7.4 KiB
C
268 lines
7.4 KiB
C
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
#ifndef _DEFINES_H
|
|
#define _DEFINES_H
|
|
|
|
// Internal defines, don't edit and expect things to work
|
|
// -------------------------------------------------------
|
|
|
|
#define TRUE 1
|
|
#define FALSE 0
|
|
#define ToRad(x) (x*0.01745329252) // *pi/180
|
|
#define ToDeg(x) (x*57.2957795131) // *180/pi
|
|
|
|
#define DEBUG 0
|
|
#define LOITER_RANGE 60 // for calculating power outside of loiter radius
|
|
#define SERVO_MAX 4500 // This value represents 45 degrees and is just an arbitrary representation of servo max travel.
|
|
|
|
// failsafe
|
|
// ----------------------
|
|
#define FAILSAFE_NONE 0
|
|
#define FAILSAFE_SHORT 1
|
|
#define FAILSAFE_LONG 2
|
|
#define FAILSAFE_GCS 3
|
|
#define FAILSAFE_SHORT_TIME 1500 // Miliiseconds
|
|
#define FAILSAFE_LONG_TIME 20000 // Miliiseconds
|
|
|
|
|
|
// active altitude sensor
|
|
// ----------------------
|
|
#define SONAR 0
|
|
#define BARO 1
|
|
|
|
#define SONAR_SOURCE_ADC 1
|
|
#define SONAR_SOURCE_ANALOG_PIN 2
|
|
|
|
// CH 7 control
|
|
#define CH7_DO_NOTHING 0
|
|
#define CH7_SAVE_WP 1
|
|
#define CH7_LEO 2
|
|
#define CH7_THERMAL 3
|
|
#define CH7_SARSEC 4
|
|
#define CH7_SARGRID 5
|
|
#define CH7_RTL 6
|
|
#define CH7_TUNING 7
|
|
|
|
// CH_7 Tuning
|
|
// -----------
|
|
#define TUN_NONE 0
|
|
// Attitude
|
|
#define TUN_STABILIZE_KP 1
|
|
#define TUN_STABILIZE_KI 2
|
|
#define TUN_STABILIZE_KD 3
|
|
#define TUN_YAW_KP 4
|
|
#define TUN_YAW_KI 5
|
|
#define TUN_YAW_KD 6
|
|
#define TUN_STABROLL_KP 7
|
|
#define TUN_STABROLL_KI 8
|
|
#define TUN_STABROLL_KD 9
|
|
#define TUN_STABPITCH_KP 10
|
|
#define TUN_STABPITCH_KI 11
|
|
#define TUN_STABPITCH_KD 12
|
|
|
|
#define PITOT_SOURCE_ADC 1
|
|
#define PITOT_SOURCE_ANALOG_PIN 2
|
|
|
|
#define T6 1000000
|
|
#define T7 10000000
|
|
|
|
// GPS type codes - use the names, not the numbers
|
|
#define GPS_PROTOCOL_NONE -1
|
|
#define GPS_PROTOCOL_NMEA 0
|
|
#define GPS_PROTOCOL_SIRF 1
|
|
#define GPS_PROTOCOL_UBLOX 2
|
|
#define GPS_PROTOCOL_IMU 3
|
|
#define GPS_PROTOCOL_MTK 4
|
|
#define GPS_PROTOCOL_HIL 5
|
|
#define GPS_PROTOCOL_MTK16 6
|
|
#define GPS_PROTOCOL_AUTO 7
|
|
|
|
#define CH_ROLL CH_1
|
|
#define CH_PITCH CH_2
|
|
#define CH_THROTTLE CH_3
|
|
#define CH_RUDDER CH_4
|
|
#define CH_YAW CH_4
|
|
#define CH_AIL1 CH_5
|
|
#define CH_AIL2 CH_6
|
|
|
|
// HIL enumerations
|
|
#define HIL_MODE_DISABLED 0
|
|
#define HIL_MODE_ATTITUDE 1
|
|
#define HIL_MODE_SENSORS 2
|
|
|
|
// Auto Pilot modes
|
|
// ----------------
|
|
#define MANUAL 0
|
|
#define CIRCLE 1 // When flying sans GPS, and we loose the radio, just circle
|
|
#define LEARNING 2
|
|
|
|
#define FLY_BY_WIRE_A 5 // Fly By Wire A has left stick horizontal => desired roll angle, left stick vertical => desired pitch angle, right stick vertical = manual throttle
|
|
#define FLY_BY_WIRE_B 6 // Fly By Wire B has left stick horizontal => desired roll angle, left stick vertical => desired pitch angle, right stick vertical => desired airspeed
|
|
#define FLY_BY_WIRE_C 7 // Fly By Wire C has left stick horizontal => desired roll angle, left stick vertical => desired climb rate, right stick vertical => desired airspeed
|
|
// Fly By Wire B and Fly By Wire C require airspeed sensor
|
|
#define AUTO 10
|
|
#define RTL 11
|
|
#define LOITER 12
|
|
//#define TAKEOFF 13 // This is not used by APM. It appears here for consistency with ACM
|
|
//#define LAND 14 // This is not used by APM. It appears here for consistency with ACM
|
|
#define GUIDED 15
|
|
#define INITIALISING 16 // in startup routines
|
|
#define HEADALT 17 // Lock the current heading and altitude
|
|
#define LAND 21 // Landing mode
|
|
|
|
// Commands - Note that APM now uses a subset of the MAVLink protocol commands. See enum MAV_CMD in the GCS_Mavlink library
|
|
#define CMD_BLANK 0 // there is no command stored in the mem location requested
|
|
#define NO_COMMAND 0
|
|
#define WAIT_COMMAND 255
|
|
|
|
// Command/Waypoint/Location Options Bitmask
|
|
//--------------------
|
|
#define MASK_OPTIONS_RELATIVE_ALT (1<<0) // 1 = Relative altitude
|
|
|
|
//repeating events
|
|
#define NO_REPEAT 0
|
|
#define CH_5_TOGGLE 1
|
|
#define CH_6_TOGGLE 2
|
|
#define CH_7_TOGGLE 3
|
|
#define CH_8_TOGGLE 4
|
|
#define RELAY_TOGGLE 5
|
|
#define STOP_REPEAT 10
|
|
|
|
#define MAV_CMD_CONDITION_YAW 23
|
|
|
|
// GCS Message ID's
|
|
/// NOTE: to ensure we never block on sending MAVLink messages
|
|
/// please keep each MSG_ to a single MAVLink message. If need be
|
|
/// create new MSG_ IDs for additional messages on the same
|
|
/// stream
|
|
enum ap_message {
|
|
MSG_HEARTBEAT,
|
|
MSG_ATTITUDE,
|
|
MSG_LOCATION,
|
|
MSG_EXTENDED_STATUS1,
|
|
MSG_EXTENDED_STATUS2,
|
|
MSG_NAV_CONTROLLER_OUTPUT,
|
|
MSG_CURRENT_WAYPOINT,
|
|
MSG_VFR_HUD,
|
|
MSG_RADIO_OUT,
|
|
MSG_RADIO_IN,
|
|
MSG_RAW_IMU1,
|
|
MSG_RAW_IMU2,
|
|
MSG_RAW_IMU3,
|
|
MSG_GPS_STATUS,
|
|
MSG_GPS_RAW,
|
|
MSG_SERVO_OUT,
|
|
MSG_NEXT_WAYPOINT,
|
|
MSG_NEXT_PARAM,
|
|
MSG_STATUSTEXT,
|
|
MSG_FENCE_STATUS,
|
|
MSG_AHRS,
|
|
MSG_SIMSTATE,
|
|
MSG_HWSTATUS,
|
|
MSG_RETRY_DEFERRED // this must be last
|
|
};
|
|
|
|
enum gcs_severity {
|
|
SEVERITY_LOW=1,
|
|
SEVERITY_MEDIUM,
|
|
SEVERITY_HIGH,
|
|
SEVERITY_CRITICAL
|
|
};
|
|
|
|
// Logging parameters
|
|
#define LOG_INDEX_MSG 0xF0
|
|
#define LOG_ATTITUDE_MSG 0x01
|
|
#define LOG_GPS_MSG 0x02
|
|
#define LOG_MODE_MSG 0X03
|
|
#define LOG_CONTROL_TUNING_MSG 0X04
|
|
#define LOG_NAV_TUNING_MSG 0X05
|
|
#define LOG_PERFORMANCE_MSG 0X06
|
|
#define LOG_RAW_MSG 0x07
|
|
#define LOG_CMD_MSG 0x08
|
|
#define LOG_CURRENT_MSG 0x09
|
|
#define LOG_STARTUP_MSG 0x0A
|
|
#define TYPE_AIRSTART_MSG 0x00
|
|
#define TYPE_GROUNDSTART_MSG 0x01
|
|
#define MAX_NUM_LOGS 100
|
|
|
|
#define MASK_LOG_ATTITUDE_FAST (1<<0)
|
|
#define MASK_LOG_ATTITUDE_MED (1<<1)
|
|
#define MASK_LOG_GPS (1<<2)
|
|
#define MASK_LOG_PM (1<<3)
|
|
#define MASK_LOG_CTUN (1<<4)
|
|
#define MASK_LOG_NTUN (1<<5)
|
|
#define MASK_LOG_MODE (1<<6)
|
|
#define MASK_LOG_RAW (1<<7)
|
|
#define MASK_LOG_CMD (1<<8)
|
|
#define MASK_LOG_CUR (1<<9)
|
|
|
|
// Waypoint Modes
|
|
// ----------------
|
|
#define ABS_WP 0
|
|
#define REL_WP 1
|
|
|
|
// Command Queues
|
|
// ---------------
|
|
#define COMMAND_MUST 0
|
|
#define COMMAND_MAY 1
|
|
#define COMMAND_NOW 2
|
|
|
|
// Events
|
|
// ------
|
|
#define EVENT_WILL_REACH_WAYPOINT 1
|
|
#define EVENT_SET_NEW_COMMAND_INDEX 2
|
|
#define EVENT_LOADED_WAYPOINT 3
|
|
#define EVENT_LOOP 4
|
|
|
|
// Climb rate calculations
|
|
#define ALTITUDE_HISTORY_LENGTH 8 //Number of (time,altitude) points to regress a climb rate from
|
|
|
|
|
|
#define BATTERY_VOLTAGE(x) (x*(g.input_voltage/1024.0))*g.volt_div_ratio
|
|
#define CURRENT_AMPS(x) ((x*(g.input_voltage/1024.0))-CURR_AMPS_OFFSET)*g.curr_amp_per_volt
|
|
|
|
#define RELAY_PIN 47
|
|
|
|
|
|
// sonar
|
|
#define MAX_SONAR_XL 0
|
|
#define MAX_SONAR_LV 1
|
|
#define SonarToCm(x) (x*1.26) // Sonar raw value to centimeters
|
|
#define AN4 4
|
|
#define AN5 5
|
|
|
|
#define SPEEDFILT 400 // centimeters/second; the speed below which a groundstart will be triggered
|
|
|
|
|
|
// EEPROM addresses
|
|
#define EEPROM_MAX_ADDR 4096
|
|
// parameters get the first 1KiB of EEPROM, remainder is for waypoints
|
|
#define WP_START_BYTE 0x400 // where in memory home WP is stored + all other WP
|
|
#define WP_SIZE 15
|
|
|
|
// fence points are stored at the end of the EEPROM
|
|
#define MAX_FENCEPOINTS 20
|
|
#define FENCE_WP_SIZE sizeof(Vector2l)
|
|
#define FENCE_START_BYTE (EEPROM_MAX_ADDR-(MAX_FENCEPOINTS*FENCE_WP_SIZE))
|
|
|
|
#define MAX_WAYPOINTS ((FENCE_START_BYTE - WP_START_BYTE) / WP_SIZE) - 1 // - 1 to be safe
|
|
|
|
#define ONBOARD_PARAM_NAME_LENGTH 15
|
|
|
|
// convert a boolean (0 or 1) to a sign for multiplying (0 maps to 1, 1 maps to -1)
|
|
#define BOOL_TO_SIGN(bvalue) ((bvalue)?-1:1)
|
|
|
|
// mark a function as not to be inlined
|
|
#define NOINLINE __attribute__((noinline))
|
|
|
|
#define CONFIG_IMU_OILPAN 1
|
|
#define CONFIG_IMU_MPU6000 2
|
|
|
|
#define APM_HARDWARE_APM1 1
|
|
#define APM_HARDWARE_APM2 2
|
|
|
|
#define AP_BARO_BMP085 1
|
|
#define AP_BARO_MS5611 2
|
|
|
|
#endif // _DEFINES_H
|