mirror of https://github.com/ArduPilot/ardupilot
266 lines
6.3 KiB
Plaintext
266 lines
6.3 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for FMUv4pro hardware (Pixhawk 3 Pro)
|
|
|
|
define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_FMUV4PRO
|
|
|
|
define BOARD_TYPE_DEFAULT 14
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F469xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 13
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
# board voltage
|
|
STM32_VDD 330U
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
|
|
env OPTIMIZE -O2
|
|
|
|
# serial port for stdout, disabled so console is on USB
|
|
#STDOUT_SERIAL SD7
|
|
#STDOUT_BAUDRATE 57600
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C1 I2C2
|
|
|
|
# now the UART order. These map to the hal.uartA to hal.uartF
|
|
# objects. If you use a shorter list then HAL_Empty::UARTDriver
|
|
# objects are substituted for later UARTs, or you can leave a gap by
|
|
# listing one or more of the uarts as EMPTY
|
|
# 1) SERIAL0: console (primary mavlink, usually USB)
|
|
# 2) SERIAL3: primary GPS
|
|
# 3) SERIAL1: telem1
|
|
# 4) SERIAL2: telem2
|
|
# 5) SERIAL4: GPS2
|
|
# 6) SERIAL5: extra UART (usually RTOS debug console)
|
|
|
|
# order of UARTs (and USB)
|
|
UART_ORDER OTG1 UART4 USART2 USART3 UART8 USART1 UART7
|
|
|
|
# UART for IOMCU
|
|
IOMCU_UART USART6
|
|
|
|
# we have a safety switch on IO
|
|
define HAL_HAVE_SAFETY_SWITCH 1
|
|
|
|
# UART4 serial GPS
|
|
PA0 UART4_TX UART4
|
|
PA1 UART4_RX UART4
|
|
|
|
# battery connectors
|
|
PA2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
# VDD sense pin. This is used to sense primary board voltags
|
|
PA4 VDD_5V_SENS ADC1 SCALE(2)
|
|
|
|
# SPI1 is sensors bus
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# SPI1 CS pins
|
|
PC2 MPU9250_CS CS
|
|
PC15 20608_CS CS
|
|
PD7 BARO_CS CS
|
|
PE15 MAG_CS CS
|
|
PH5 EEPROM_CS CS
|
|
|
|
PA9 VBUS INPUT OPENDRAIN
|
|
|
|
# now we define the pins that USB is connected on
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# these are the pins for SWD debugging with a STlinkv2 or black-magic probe
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# PWM output for buzzer
|
|
PA15 TIM2_CH1 TIM2 GPIO(77) ALARM
|
|
|
|
# this defines a couple of general purpose outputs, mapped to GPIO
|
|
# numbers 1 and 2 for users
|
|
# PB0 EXTERN_GPIO1 OUTPUT GPIO(1)
|
|
# PB1 EXTERN_GPIO2 OUTPUT GPIO(2)
|
|
|
|
#PB0 INPUT PULLUP # RC Input PPM
|
|
|
|
PB1 LED_GREEN OUTPUT GPIO(0)
|
|
PB2 BOOT1 INPUT
|
|
PB3 LED_BLUE OUTPUT GPIO(1)
|
|
|
|
PB6 USART1_TX USART1
|
|
PB7 USART1_RX USART1
|
|
PA8 USART1_RTS USART1
|
|
# PE10 is not a hw CTS pin for USART1
|
|
PE10 8266_CTS INPUT
|
|
|
|
# make GPIOs for ESP8266 available via mavlink relay control as pins
|
|
# 60 to 63
|
|
PB4 8266_GPIO2 OUTPUT GPIO(60)
|
|
PE2 8266_GPI0 INPUT PULLUP GPIO(61)
|
|
PE5 8266_PD OUTPUT HIGH GPIO(62)
|
|
PE6 8266_RST OUTPUT HIGH GPIO(63)
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
PF1 I2C2_SCL I2C2
|
|
PF0 I2C2_SDA I2C2
|
|
|
|
# SPI2 is FRAM
|
|
PB10 SPI2_SCK SPI2
|
|
PB11 LED_RED OUTPUT GPIO(2)
|
|
PB12 CAN2_RX CAN2
|
|
PB13 CAN2_TX CAN2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
PC0 VBUS_VALID INPUT
|
|
PC1 BATT2_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC3 BATT2_CURRENT_SENS ADC1 SCALE(1)
|
|
#PC4 SAFETY_IN INPUT PULLDOWN
|
|
|
|
# this sets up the UART for talking to the IOMCU. Note that it is
|
|
# vital that this UART has DMA available. See the DMA settings below
|
|
# for more information
|
|
|
|
# USART6 to IO
|
|
PC6 USART6_TX USART6
|
|
PC7 USART6_RX USART6
|
|
|
|
# now setup the pins for the microSD card, if available
|
|
PC8 SDIO_D0 SDIO
|
|
PC9 SDIO_D1 SDIO
|
|
PC10 SDIO_D2 SDIO
|
|
PC11 SDIO_D3 SDIO
|
|
PC12 SDIO_CK SDIO
|
|
PC13 SBUS_INV OUTPUT
|
|
PC14 20608_DRDY INPUT
|
|
|
|
PD0 CAN1_RX CAN1
|
|
PD1 CAN1_TX CAN1
|
|
PD2 SDIO_CMD SDIO
|
|
|
|
# USART2 serial2 telem1
|
|
PD3 USART2_CTS USART2
|
|
PD4 USART2_RTS USART2
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
|
|
# USART3 serial3 telem2
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
PD10 FRAM_CS CS
|
|
PD11 USART3_CTS USART3
|
|
PD12 USART3_RTS USART3
|
|
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
|
|
PD15 MPU9250_DRDY INPUT
|
|
|
|
# UART8 serial4 FrSky
|
|
PE0 UART8_RX UART8
|
|
PE1 UART8_TX UART8
|
|
# allow this uart to be inverted for transmit under user control
|
|
# the polarity is the value to use on the GPIO to change the polarity
|
|
# to the opposite of the default
|
|
PA10 UART8_TXINV OUTPUT HIGH GPIO(78) POL(0)
|
|
|
|
PE3 VDD_SENSORS_EN OUTPUT HIGH
|
|
|
|
# start peripheral power off, then enable after init
|
|
# this prevents a problem with radios that use RTS for
|
|
# bootloader hold
|
|
PC5 VDD_5V_WIFI_EN OUTPUT HIGH
|
|
PF4 nVDD_5V_HIPOWER_EN OUTPUT HIGH
|
|
PG10 nVDD_5V_PERIPH_EN OUTPUT HIGH
|
|
|
|
# UART7 is debug
|
|
PE7 UART7_RX UART7 NODMA
|
|
PE8 UART7_TX UART7 NODMA
|
|
|
|
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
|
PE12 MAG_DRDY INPUT
|
|
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
|
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
|
|
|
|
# Power flag pins: these tell the MCU the status of the various power
|
|
# supplies that are available. The pin names need to exactly match the
|
|
# names used in AnalogIn.cpp.
|
|
PB5 VDD_BRICK_VALID INPUT PULLUP
|
|
PG5 VDD_BRICK2_VALID INPUT PULLUP
|
|
PF3 VDD_5V_HIPOWER_OC INPUT PULLUP
|
|
PG4 VDD_5V_PERIPH_OC INPUT PULLUP
|
|
|
|
# SPI device table
|
|
SPIDEV ms5611 SPI1 DEVID3 BARO_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV mpu9250 SPI1 DEVID4 MPU9250_CS MODE3 2*MHZ 4*MHZ
|
|
SPIDEV icm20608 SPI1 DEVID6 20608_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV lis3mdl SPI1 DEVID5 MAG_CS MODE3 500*KHZ 500*KHZ
|
|
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
|
|
# two IMUs
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
|
IMU Invensense SPI:icm20608 ROTATION_ROLL_180_YAW_90
|
|
IMU Invensense SPI:mpu9250 ROTATION_ROLL_180_YAW_90
|
|
|
|
# one baro
|
|
BARO MS56XX SPI:ms5611
|
|
|
|
# two compasses
|
|
COMPASS AK8963:probe_mpu9250 0 ROTATION_ROLL_180_YAW_90
|
|
COMPASS LIS3MDL SPI:lis3mdl false ROTATION_NONE
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
define HAL_CHIBIOS_ARCH_FMUV4PRO 1
|
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# fallback to flash is no FRAM fitted
|
|
define STORAGE_FLASH_PAGE 22
|
|
|
|
# enable FAT filesystem support (needs a microSD defined via SDIO)
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# enable RTSCTS support
|
|
define AP_FEATURE_RTSCTS 1
|
|
|
|
# enable SBUS_OUT on IOMCU (if you have an IOMCU)
|
|
define AP_FEATURE_SBUS_OUT 1
|
|
|
|
# battery setup
|
|
define HAL_BATT_VOLT_PIN 2
|
|
define HAL_BATT_CURR_PIN 3
|
|
define HAL_BATT_VOLT_SCALE 10.1
|
|
define HAL_BATT_CURR_SCALE 17.0
|
|
|
|
# setup serial port defaults for ESP8266
|
|
define HAL_SERIAL5_PROTOCOL SerialProtocol_MAVLink
|
|
define HAL_SERIAL5_BAUD 921600
|
|
|
|
# 8 PWM available by default
|
|
define BOARD_PWM_COUNT_DEFAULT 6
|
|
|
|
# We can't share the IO UART (USART6).
|
|
DMA_NOSHARE USART6_TX USART6_RX ADC1
|
|
DMA_PRIORITY USART6*
|
|
|
|
ROMFS io_firmware.bin Tools/IO_Firmware/iofirmware_lowpolh.bin
|