ardupilot/Tools/AP_Periph/rc_out.cpp

115 lines
3.5 KiB
C++

/*
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include <AP_HAL/AP_HAL.h>
#ifdef HAL_PERIPH_ENABLE_RC_OUT
#include "AP_Periph.h"
// magic value from UAVCAN driver packet
// dsdl/uavcan/equipment/esc/1030.RawCommand.uavcan
// Raw ESC command normalized into [-8192, 8191]
#define UAVCAN_ESC_MAX_VALUE 8191
#define SERVO_OUT_RCIN_MAX 16 // SRV_Channel::k_rcin1 ... SRV_Channel::k_rcin16
#define SERVO_OUT_MOTOR_MAX 12 // SRV_Channel::k_motor1 ... SRV_Channel::k_motor8, SRV_Channel::k_motor9 ... SRV_Channel::k_motor12
#if HAL_PWM_COUNT == 0
#error "You must define a PWM output in your hwdef.dat"
#endif
extern const AP_HAL::HAL &hal;
void AP_Periph_FW::rcout_init()
{
// start up with safety enabled. This disables the pwm output until we receive an packet from the rempte system
hal.rcout->force_safety_on();
for (uint8_t i=0; i<HAL_PWM_COUNT; i++) {
servo_channels.set_default_function(i, SRV_Channel::Aux_servo_function_t(SRV_Channel::k_rcin1 + i));
}
for (uint8_t i=0; i<SERVO_OUT_RCIN_MAX; i++) {
SRV_Channels::set_angle(SRV_Channel::Aux_servo_function_t(SRV_Channel::k_rcin1 + i), 1000);
}
for (uint8_t i=0; i<SERVO_OUT_MOTOR_MAX; i++) {
SRV_Channels::set_angle(SRV_Channels::get_motor_function(i), UAVCAN_ESC_MAX_VALUE);
}
// run this once and at 1Hz to configure aux and esc ranges
rcout_init_1Hz();
}
void AP_Periph_FW::rcout_init_1Hz()
{
// this runs at 1Hz to allow for run-time param changes
SRV_Channels::enable_aux_servos();
for (uint8_t i=0; i<SERVO_OUT_MOTOR_MAX; i++) {
servo_channels.set_esc_scaling_for(SRV_Channels::get_motor_function(i));
}
}
void AP_Periph_FW::rcout_esc(int16_t *rc, uint8_t num_channels)
{
if (rc == nullptr) {
return;
}
const uint8_t channel_count = MIN(num_channels, SERVO_OUT_MOTOR_MAX);
for (uint8_t i=0; i<channel_count; i++) {
SRV_Channels::set_output_scaled(SRV_Channels::get_motor_function(i), rc[i]);
}
rcout_has_new_data_to_update = true;
}
void AP_Periph_FW::rcout_srv(uint8_t actuator_id, const float command_value)
{
if ((actuator_id == 0) || (actuator_id > HAL_PWM_COUNT)) {
// not supported or out of range
return;
}
const SRV_Channel::Aux_servo_function_t function = SRV_Channel::Aux_servo_function_t(SRV_Channel::k_rcin1 + actuator_id - 1);
SRV_Channels::set_output_norm(function, command_value);
rcout_has_new_data_to_update = true;
}
void AP_Periph_FW::rcout_handle_safety_state(uint8_t safety_state)
{
if (safety_state == 255) {
hal.rcout->force_safety_off();
} else {
hal.rcout->force_safety_on();
}
rcout_has_new_data_to_update = true;
}
void AP_Periph_FW::rcout_update()
{
if (!rcout_has_new_data_to_update) {
return;
}
rcout_has_new_data_to_update = false;
SRV_Channels::calc_pwm();
SRV_Channels::cork();
SRV_Channels::output_ch_all();
SRV_Channels::push();
}
#endif // HAL_PERIPH_ENABLE_RC_OUT