Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
ardupilot/libraries/AP_HAL_ChibiOS/hwdef/FlywooF405Pro
History
Andrew Tridgell ed58758ce6 hwdef: don't use DEFAULTGPIO in bootloaders 
setting up a DEFAULTGPIO pulldown in bootloaders is a bad idea as it
overrides any hardware pullups that have been put in place as part of
a "hold in bootloader" mechanism. See discussion in #27360 for ELRS

note that this only impacts one board that I can see, the
BlitzF745AIO, due to the MCU vs DEFAULTGPIO interaction
 		2024-06-25 12:05:40 +10:00
..
GOKUF405Pro_Pinout.JPG
…
README.md
…
defaults.parm
…
hwdef-bl.dat hwdef: don't use DEFAULTGPIO in bootloaders 2024-06-25 12:05:40 +10:00
hwdef.dat hwdef: remove HAL_GPIO lines which are simply the default values 2024-04-03 11:00:24 +11:00

README.md

GOKU F405 Pro

https://flywoo.net/products/goku-versatile-f405-pro-fc-20x20-30-5x30-5

The Flywoo GOKU F405 Pro is a flight controller produced by Flywoo.

Features

  • MCU: STM32F405 32-bit processor. 1024Kbytes Flash
  • IMU: ICM42688 (SPI)
  • Barometer: BMP280
  • 6 hardware UARTS (UART1,2,3,4,5,6)
  • Onbord 16Mbytes for Blackbox logging
  • 5V Power Out: 2.0A max
  • 10V Power Out: 2.0A max
  • 9 PWM outputs
  • Mounting Holes: Standard 20x20 or 30.5/30.5mm square to center of holes
  • Weight: 5.5g
  • Input Voltage: 2-6S Lipo

Pinout

GOKU F405 Pro

UART Mapping

The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the receive pin for UARTn. The Tn pin is the transmit pin for UARTn.

Name Pin Function
SERIAL0 COMPUTER USB
SERIAL1 RX1/TX1 USART1 (GPS)
SERIAL2 RX2 USART2 (ESC Telemetry)
SERIAL3 TX3/RX3 USART3 (DJI, DMA-enabled)
SERIAL4 TX4/RX4 UART4 (RX/SBUS)
SERIAL5 TX5/RX5 UART5
SERIAL6 TX6/RX6 UART6 (RX, DMA-enabled)

USART3 and USART6 supports RX and TX DMA. UART4 supports TX DMA. UART1, UART2 and UART5 do not support DMA.

RC Input

RC input is configured on UART3, UART4 or UART6 which support serial RC protocols. SBUS must be used on UART4 which has hardware inversion, UART5 also has hardware inversion but no DMA so use for SBUS is not recommended.

OSD Support

The GOKU F405 Pro supports OSD using OSD_TYPE 1 (MAX7456 driver).

PWM Output

The GOKU F405 Pro supports up to 9 PWM outputs. The pads for motor output ESC1 to ESC4 on the above diagram are the first 4 outputs.All 9 outputs support DShot.

The PWM are in 5 groups:

PWM 1-2: Group 1 PWM 3-4: Group 2 PWM 5,7: Group 3 PWM 6,8: Group 4 LED: Group 5

Channels within the same group need to use the same output rate. If any channel in a group uses DShot then all channels in the group need to use DShot. PWM 1-4 support bidirectional dshot.

Battery Monitoring

The board has a builtin voltage sensor. The voltage sensor can handle 2S to 6S LiPo batteries.

The correct battery setting parameters are:

  • BATT_MONITOR 4
  • BATT_VOLT_PIN 12
  • BATT_VOLT_MULT around 11
  • BATT_CURR_PIN 13
  • BATT_CURR_MULT around 59

These are set by default in the firmware and shouldn't need to be adjusted

Compass

The GOKU F405 Pro does not have a builtin compass but it does have an external I2C connector.

NeoPixel LED

The board includes a NeoPixel LED pad.

Loading Firmware (you will need to compile your own firmware)

Initial firmware load can be done with DFU by plugging in USB with the bootloader button pressed. Then you should load the "with_bl.hex" firmware, using your favourite DFU loading tool.

Once the initial firmware is loaded you can update the firmware using any ArduPilot ground station software. Updates should be done with the *.apj firmware files.