ardupilot/libraries/AP_IOMCU/iofirmware/iofirmware.h

149 lines
3.8 KiB
C++

#include <AP_HAL/AP_HAL.h>
#include <AP_RCProtocol/AP_RCProtocol.h>
#include "ch.h"
#include "ioprotocol.h"
#define PWM_IGNORE_THIS_CHANNEL UINT16_MAX
#define SERVO_COUNT 8
class AP_IOMCU_FW {
public:
void process_io_packet();
struct IOPacket rx_io_packet, tx_io_packet, rx_io_last;
void init();
void update();
void calculate_fw_crc(void);
private:
void pwm_out_update();
void heater_update();
void rcin_update();
bool handle_code_write();
bool handle_code_read();
void schedule_reboot(uint32_t time_ms);
void safety_update();
void rcout_mode_update();
void rcin_serial_init();
void rcin_serial_update();
void page_status_update(void);
void fill_failsafe_pwm(void);
void run_mixer(void);
int16_t mix_input_angle(uint8_t channel, uint16_t radio_in) const;
int16_t mix_input_range(uint8_t channel, uint16_t radio_in) const;
uint16_t mix_output_angle(uint8_t channel, int16_t angle) const;
uint16_t mix_output_range(uint8_t channel, int16_t value) const;
int16_t mix_elevon_vtail(int16_t angle1, int16_t angle2, bool first_output) const;
void dsm_bind_step(void);
struct PACKED {
/* default to RSSI ADC functionality */
uint16_t features;
uint16_t arming;
uint16_t pwm_rates;
uint16_t pwm_defaultrate = 50;
uint16_t pwm_altrate = 200;
uint16_t relays_pad;
uint16_t vbatt_scale = 10000;
uint16_t reserved1;
uint16_t reserved2;
uint16_t set_debug;
uint16_t reboot_bl;
uint16_t crc[2];
uint16_t rc_thr_failsafe_us;
uint16_t reserved3;
uint16_t pwm_reverse;
uint16_t trim_roll;
uint16_t trim_pitch;
uint16_t trim_yaw;
uint16_t sbus_rate = 72;
uint16_t ignore_safety;
uint16_t heater_duty_cycle = 0xFFFFU;
uint16_t pwm_altclock = 1;
} reg_setup;
// CONFIG values
struct page_config config;
// PAGE_STATUS values
struct page_reg_status reg_status;
// PAGE_RAW_RCIN values
struct page_rc_input rc_input;
// PAGE_SERVO values
struct {
uint16_t pwm[IOMCU_MAX_CHANNELS];
} reg_servo;
// PAGE_DIRECT_PWM values
struct {
uint16_t pwm[IOMCU_MAX_CHANNELS];
} reg_direct_pwm;
// PAGE_FAILSAFE_PWM
struct {
uint16_t pwm[IOMCU_MAX_CHANNELS];
} reg_failsafe_pwm;
// PAGE_SAFETY_PWM
struct {
uint16_t pwm[IOMCU_MAX_CHANNELS];
} reg_safety_pwm;
// output rates
struct {
uint16_t freq;
uint16_t chmask;
uint16_t default_freq = 50;
uint16_t sbus_rate_hz;
} rate;
// MIXER values
struct page_mixing mixing;
// true when override channel active
bool override_active;
// sbus rate handling
uint32_t sbus_last_ms;
uint32_t sbus_interval_ms;
AP_RCProtocol *rcprotocol;
uint32_t fmu_data_received_time;
uint32_t last_heater_ms;
uint32_t reboot_time;
bool do_reboot;
bool update_default_rate;
bool update_rcout_freq;
bool has_heater;
uint32_t last_blue_led_ms;
uint32_t safety_update_ms;
uint32_t safety_button_counter;
uint8_t led_counter;
uint32_t last_loop_ms;
bool oneshot_enabled;
bool brushed_enabled;
thread_t *thread_ctx;
bool last_safety_off;
uint32_t last_status_ms;
uint32_t last_ms;
uint32_t loop_counter;
uint8_t dsm_bind_state;
uint32_t last_dsm_bind_ms;
uint32_t last_failsafe_ms;
};
// GPIO macros
#define HEATER_SET(on) palWriteLine(HAL_GPIO_PIN_HEATER, !(on));
#define BLUE_TOGGLE() palToggleLine(HAL_GPIO_PIN_HEATER);
#define AMBER_SET(on) palWriteLine(HAL_GPIO_PIN_AMBER_LED, !(on));
#define SPEKTRUM_POWER(on) palWriteLine(HAL_GPIO_PIN_SPEKTRUM_PWR_EN, on);
#define SPEKTRUM_SET(on) palWriteLine(HAL_GPIO_PIN_SPEKTRUM_OUT, on);