mirror of https://github.com/ArduPilot/ardupilot
205 lines
4.5 KiB
Plaintext
205 lines
4.5 KiB
Plaintext
# hwdef for Luminousbees flight board
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F427xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 11
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
# board voltage
|
|
STM32_VDD 330U
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
|
|
env OPTIMIZE -O3
|
|
|
|
# serial port for stdout disabled, use USB console
|
|
# STDOUT_SERIAL SD7
|
|
# STDOUT_BAUDRATE 57600
|
|
|
|
# only one I2C bus
|
|
I2C_ORDER I2C1
|
|
|
|
# to match px4 we make the first bus number 1
|
|
define HAL_I2C_BUS_BASE 1
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
# order of UARTs (and USB)
|
|
UART_ORDER OTG1 UART4 USART2 USART3 UART8 USART1 UART7
|
|
|
|
# UART4 is GPS
|
|
PA0 UART4_TX UART4
|
|
PA1 UART4_RX UART4
|
|
|
|
# Battery & current control
|
|
PA2 BATT_VOLTAGE_SENS ADC1
|
|
PA3 BATT_CURRENT_SENS ADC1
|
|
PA4 VDD_5V_SENS ADC1 SCALE(2)
|
|
|
|
# SPI1 is sensors bus
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
PB2 BOOT1 INPUT
|
|
PB5 VDD_BRICK_VALID INPUT
|
|
|
|
# USART1
|
|
PB6 TIM4_CH1 TIM4 PWM(7) GPIO(56) # PB6 as led strip control
|
|
#PB6 USART1_TX USART1
|
|
PB7 USART1_RX USART1
|
|
|
|
# UWB DW1000
|
|
PB4 UWB_CS CS
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# SPI2 is FRAM
|
|
PB10 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
PC0 VBUS_VALID INPUT
|
|
PC4 SAFETY_IN INPUT PULLDOWN
|
|
|
|
PC7 TIM8_CH2 TIM8 RCIN FLOAT LOW # also USART6_RX for serial RC
|
|
|
|
PC8 SDIO_D0 SDIO
|
|
PC9 SDIO_D1 SDIO
|
|
PC10 SDIO_D2 SDIO
|
|
PC11 SDIO_D3 SDIO
|
|
PC12 SDIO_CK SDIO
|
|
PD2 SDIO_CMD SDIO
|
|
|
|
# USART2 serial2 telem1 connected to ESP
|
|
|
|
PD4 BMI088_ACCEL_CS CS
|
|
PD3 BMI088_GYRO_CS CS
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
|
|
PD7 BARO_CS CS
|
|
# PB7 BARO2_CS CS # FOR DPS310 ON FRAME MICRO
|
|
|
|
# USART3 serial3 telem2
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
PD10 FRAM_CS CS
|
|
|
|
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
|
|
# UART8
|
|
PE0 UART8_RX UART8
|
|
PE1 UART8_TX UART8
|
|
|
|
#set up SPI bus4 for UWB
|
|
PE2 SPI4_SCK SPI4
|
|
PE5 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
|
|
# UART7 is debug
|
|
PE7 UART7_RX UART7 NODMA
|
|
PE8 UART7_TX UART7 NODMA
|
|
|
|
PE11 TIM1_CH2 TIM1 PWM(1) GPIO(50) #52
|
|
PE14 TIM1_CH4 TIM1 PWM(2) GPIO(51) #50
|
|
PE9 TIM1_CH1 TIM1 PWM(3) GPIO(52) #53
|
|
PE13 TIM1_CH3 TIM1 PWM(4) GPIO(53) #51
|
|
|
|
|
|
# SPI device table. The DEVID values are chosen to match the PX4 port
|
|
# of ArduPilot so users don't need to re-do their accel and compass calibrations
|
|
# when moving to ChibiOS
|
|
SPIDEV ms5611_int SPI2 DEVID3 BARO_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV bmi088_g SPI4 DEVID1 BMI088_GYRO_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV bmi088_a SPI4 DEVID2 BMI088_ACCEL_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
SPIDEV dwm1000 SPI4 DEVID5 UWB_CS MODE0 3*MHZ 20*MHZ
|
|
define HAL_CHIBIOS_ARCH_FMUV4 1
|
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
# enable RAMTROM parameter storage
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# fallback to flash is no FRAM fitted
|
|
define STORAGE_FLASH_PAGE 22
|
|
|
|
# enable FAT filesystem
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# pixracer has 3 LEDs, Red, Green, Blue
|
|
define HAL_HAVE_PIXRACER_LED
|
|
|
|
define HAL_GPIO_LED_ON 0
|
|
define HAL_GPIO_LED_OFF 1
|
|
|
|
# LED setup for PixracerLED driver
|
|
PB11 LED_RED OUTPUT GPIO(0)
|
|
PB1 LED_GREEN OUTPUT GPIO(1)
|
|
PB3 LED_BLUE OUTPUT GPIO(2)
|
|
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
define HAL_GPIO_B_LED_PIN 1
|
|
define HAL_GPIO_C_LED_PIN 2
|
|
|
|
# enable RTSCTS
|
|
define AP_FEATURE_RTSCTS 1
|
|
|
|
# battery setup
|
|
define HAL_BATT_VOLT_PIN 2
|
|
define HAL_BATT_CURR_PIN 3
|
|
define HAL_BATT_VOLT_SCALE 10.1
|
|
define HAL_BATT_CURR_SCALE 17.0
|
|
|
|
# setup serial port defaults for ESP8266
|
|
define HAL_SERIAL5_PROTOCOL SerialProtocol_MAVLink
|
|
define HAL_SERIAL5_BAUD 921600
|
|
|
|
# 6 PWM available by default
|
|
define BOARD_PWM_COUNT_DEFAULT 6
|
|
|
|
|
|
# Set one or two IMUs
|
|
#IMU Invensense SPI:icm20608 ROTATION_YAW_180
|
|
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_ROLL_180_YAW_90
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
|
|
|
# 2 compasses. R15 has LIS3MDL instead of HMC5843
|
|
COMPASS HMC5843 SPI:hmc5843 false ROTATION_PITCH_180
|
|
COMPASS LIS3MDL SPI:lis3mdl false ROTATION_NONE
|
|
|
|
# also probe all types of external I2C compasses
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
# Barometer ( DPS310 under test on micro frame )
|
|
BARO MS56XX SPI:ms5611_int
|
|
# BARO DPS280 SPI:dps310
|
|
|
|
# reserve plenty of memory for DMA for LED buffers
|
|
define DMA_RESERVE_SIZE 32768
|
|
|
|
# .env DEFAULT_PARAMETERS 'Tools/Frame_params/LuminousBee4_outdoor.param'
|