ardupilot/ArduCopter/sensors.pde

125 lines
3.3 KiB
Plaintext

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
// Sensors are not available in HIL_MODE_ATTITUDE
#if HIL_MODE != HIL_MODE_ATTITUDE
#if CONFIG_SONAR == ENABLED
static void init_sonar(void)
{
#if CONFIG_SONAR_SOURCE == SONAR_SOURCE_ADC
sonar->calculate_scaler(g.sonar_type, 3.3f);
#else
sonar->calculate_scaler(g.sonar_type, 5.0f);
#endif
}
#endif
static void init_barometer(bool full_calibration)
{
gcs_send_text_P(SEVERITY_LOW, PSTR("Calibrating barometer"));
if (full_calibration) {
barometer.calibrate();
}else{
barometer.update_calibration();
}
gcs_send_text_P(SEVERITY_LOW, PSTR("barometer calibration complete"));
}
// return barometric altitude in centimeters
static int32_t read_barometer(void)
{
barometer.read();
return barometer.get_altitude() * 100.0f;
}
// return sonar altitude in centimeters
static int16_t read_sonar(void)
{
#if CONFIG_SONAR == ENABLED
// exit immediately if sonar is disabled
if( !g.sonar_enabled ) {
sonar_alt_health = 0;
return 0;
}
int16_t temp_alt = sonar->read();
if (temp_alt >= sonar->min_distance && temp_alt <= sonar->max_distance * SONAR_RELIABLE_DISTANCE_PCT) {
if ( sonar_alt_health < SONAR_ALT_HEALTH_MAX ) {
sonar_alt_health++;
}
}else{
sonar_alt_health = 0;
}
#if SONAR_TILT_CORRECTION == 1
// correct alt for angle of the sonar
float temp = ahrs.cos_pitch() * ahrs.cos_roll();
temp = max(temp, 0.707f);
temp_alt = (float)temp_alt * temp;
#endif
return temp_alt;
#else
return 0;
#endif
}
#endif // HIL_MODE != HIL_MODE_ATTITUDE
static void init_compass()
{
if (!compass.init() || !compass.read()) {
// make sure we don't pass a broken compass to DCM
cliSerial->println_P(PSTR("COMPASS INIT ERROR"));
Log_Write_Error(ERROR_SUBSYSTEM_COMPASS,ERROR_CODE_FAILED_TO_INITIALISE);
return;
}
ahrs.set_compass(&compass);
}
static void init_optflow()
{
#if OPTFLOW == ENABLED
optflow.init();
if (!optflow.healthy()) {
g.optflow_enabled = false;
cliSerial->print_P(PSTR("Failed to Init OptFlow\n"));
Log_Write_Error(ERROR_SUBSYSTEM_OPTFLOW,ERROR_CODE_FAILED_TO_INITIALISE);
}
#endif // OPTFLOW == ENABLED
}
// read_battery - check battery voltage and current and invoke failsafe if necessary
// called at 10hz
static void read_battery(void)
{
battery.read();
// update compass with current value
if (battery.monitoring() == AP_BATT_MONITOR_VOLTAGE_AND_CURRENT) {
compass.set_current(battery.current_amps());
}
// check for low voltage or current if the low voltage check hasn't already been triggered
// we only check when we're not powered by USB to avoid false alarms during bench tests
if (!ap.usb_connected && !failsafe.battery && battery.exhausted(g.fs_batt_voltage, g.fs_batt_mah)) {
failsafe_battery_event();
}
}
// read the receiver RSSI as an 8 bit number for MAVLink
// RC_CHANNELS_SCALED message
void read_receiver_rssi(void)
{
// avoid divide by zero
if (g.rssi_range <= 0) {
receiver_rssi = 0;
}else{
rssi_analog_source->set_pin(g.rssi_pin);
float ret = rssi_analog_source->voltage_average() * 255 / g.rssi_range;
receiver_rssi = constrain_int16(ret, 0, 255);
}
}