mirror of https://github.com/ArduPilot/ardupilot
114 lines
2.2 KiB
Plaintext
114 lines
2.2 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
|
|
# Sierra RM3100 & Airspeed common hwdef
|
|
|
|
# MCU class and specific type
|
|
MCU STM32L431 STM32L431xx
|
|
|
|
# bootloader starts firmware at 36k + 4k (STORAGE_FLASH)
|
|
FLASH_RESERVE_START_KB 40
|
|
|
|
# store parameters in pages 18 and 19
|
|
STORAGE_FLASH_PAGE 18
|
|
define HAL_STORAGE_SIZE 800
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 15
|
|
define CH_CFG_ST_RESOLUTION 16
|
|
|
|
# enable watchdog
|
|
define HAL_WATCHDOG_ENABLED_DEFAULT true
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1050
|
|
|
|
# setup build for a peripheral firmware
|
|
env AP_PERIPH 1
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
# Flash available
|
|
FLASH_SIZE_KB 256
|
|
|
|
define HAL_CAN_POOL_SIZE 6000
|
|
|
|
# LEDs
|
|
PA15 LED OUTPUT LOW GPIO(1)
|
|
|
|
STDOUT_SERIAL SD1
|
|
STDOUT_BAUDRATE 57600
|
|
|
|
# order of UARTs
|
|
SERIAL_ORDER USART1
|
|
|
|
# USART1
|
|
PA9 USART1_TX USART1 SPEED_HIGH NODMA
|
|
PA10 USART1_RX USART1 SPEED_HIGH NODMA
|
|
|
|
define HAL_USE_SERIAL TRUE
|
|
define STM32_SERIAL_USE_USART1 TRUE
|
|
define SERIAL_BUFFERS_SIZE 32
|
|
|
|
# SPI1 bus for RM3100
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
PB12 MAG_CS CS
|
|
|
|
# compass
|
|
SPIDEV rm3100 SPI1 DEVID1 MAG_CS MODE0 1*MHZ 1*MHZ
|
|
COMPASS RM3100 SPI:rm3100 false ROTATION_PITCH_180
|
|
|
|
# MS4525DO Airspeed
|
|
PB6 I2C1_SCL I2C1
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
define HAL_I2C_CLEAR_ON_TIMEOUT 0
|
|
define HAL_I2C_INTERNAL_MASK 1
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
# allow for reboot command for faster development
|
|
define HAL_PERIPH_LISTEN_FOR_SERIAL_UART_REBOOT_CMD_PORT 0
|
|
|
|
# debugger support
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
define DMA_RESERVE_SIZE 2048
|
|
|
|
# stack for fast interrupts
|
|
define PORT_INT_REQUIRED_STACK 64
|
|
|
|
# MAIN_STACK is stack for ISR handlers
|
|
MAIN_STACK 0x300
|
|
|
|
# PROCESS_STACK controls stack for main thread
|
|
PROCESS_STACK 0xA00
|
|
|
|
define HAL_DISABLE_LOOP_DELAY
|
|
|
|
# enable CAN support
|
|
PA11 CAN1_RX CAN1
|
|
PA12 CAN1_TX CAN1
|
|
CAN_ORDER 1
|
|
|
|
define HAL_USE_ADC TRUE
|
|
define STM32_ADC_USE_ADC1 TRUE
|
|
PA0 VSENSE ADC1 SCALE(2)
|
|
|
|
define HAL_GCS_ENABLED 0
|
|
define HAL_NO_MONITOR_THREAD
|
|
define HAL_NO_LOGGING
|
|
define HAL_MINIMIZE_FEATURES 0
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 512
|
|
|
|
define CAN_APP_NODE_NAME "org.ardupilot.Sierra-L431"
|
|
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
define HAL_PERIPH_ENABLE_AIRSPEED
|
|
define AIRSPEED_MAX_SENSORS 1
|
|
define HAL_AIRSPEED_TYPE_DEFAULT 1
|