mirror of https://github.com/ArduPilot/ardupilot
106 lines
1.9 KiB
Plaintext
106 lines
1.9 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# MCU class and specific type
|
|
|
|
# MCU class and specific type
|
|
MCU STM32G4xx STM32G474xx
|
|
|
|
FLASH_RESERVE_START_KB 36
|
|
|
|
STORAGE_FLASH_PAGE 16
|
|
define HAL_STORAGE_SIZE 800
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1088
|
|
|
|
# setup build for a peripheral firmware
|
|
env AP_PERIPH 1
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
define CH_CFG_ST_FREQUENCY 1000000
|
|
|
|
# assume 512k flash part
|
|
FLASH_SIZE_KB 512
|
|
|
|
# debug on USART2
|
|
STDOUT_SERIAL SD2
|
|
STDOUT_BAUDRATE 57600
|
|
|
|
# order of UARTs
|
|
SERIAL_ORDER USART2
|
|
|
|
# sensor power control
|
|
PC11 VDD_3V3_SENSORS_EN OUTPUT HIGH
|
|
|
|
# LEDs
|
|
PC10 LED OUTPUT HIGH GPIO(2) # blue
|
|
PB15 LED_R OUTPUT HIGH GPIO(0)
|
|
PC6 LED_G OUTPUT HIGH GPIO(1)
|
|
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
define HAL_GPIO_B_LED_PIN 1
|
|
define HAL_GPIO_C_LED_PIN 2
|
|
|
|
define HAL_GPIO_LED_ON 0
|
|
define HAL_GPIO_LED_OFF 1
|
|
|
|
define HAL_HAVE_PIXRACER_LED
|
|
|
|
# USART2, debug
|
|
PA2 USART2_TX USART2
|
|
PA3 USART2_RX USART2
|
|
|
|
# SWD debugging
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# one SPI bus
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# SPI CS
|
|
PC14 MAG_CS CS
|
|
|
|
# SPI devices
|
|
SPIDEV rm3100 SPI1 DEVID1 MAG_CS MODE0 1*MHZ 1*MHZ
|
|
|
|
# compass
|
|
COMPASS RM3100 SPI:rm3100 false ROTATION_NONE
|
|
|
|
define HAL_USE_ADC FALSE
|
|
define STM32_ADC_USE_ADC1 FALSE
|
|
define HAL_DISABLE_ADC_DRIVER TRUE
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
|
|
# avoid RCIN thread to save memory
|
|
define HAL_NO_RCIN_THREAD
|
|
|
|
define HAL_USE_RTC FALSE
|
|
define DISABLE_SERIAL_ESC_COMM TRUE
|
|
|
|
define DMA_RESERVE_SIZE 0
|
|
|
|
define HAL_DISABLE_LOOP_DELAY
|
|
|
|
# enable CAN support
|
|
PA11 CAN1_RX CAN1
|
|
PA12 CAN1_TX CAN1
|
|
PC13 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
|
|
|
|
define HAL_NO_MONITOR_THREAD
|
|
|
|
define HAL_DEVICE_THREAD_STACK 768
|
|
|
|
# we setup a small defaults.parm
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 256
|
|
|
|
# MAG
|
|
define HAL_PERIPH_ENABLE_MAG
|
|
|
|
# keep ROMFS uncompressed as we don't have enough RAM
|
|
# to uncompress the bootloader at runtime
|
|
env ROMFS_UNCOMPRESSED True
|