mirror of
https://github.com/ArduPilot/ardupilot
synced 2025-02-28 18:53:57 -04:00
308 lines
6.7 KiB
Plaintext
308 lines
6.7 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for the SULILGH7_P1 hardware
|
|
|
|
# default to all pins low to avoid ESD issues
|
|
DEFAULTGPIO OUTPUT LOW PULLDOWN
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 2
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID AP_HW_SULILGH7-P1-P2
|
|
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# to be compatible with the px4 bootloader we need
|
|
# to use a different RAM_MAP
|
|
env USE_ALT_RAM_MAP 1
|
|
|
|
MCU_CLOCKRATE_MHZ 480
|
|
|
|
env OPTIMIZE -O2
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART2 USART3 USART1 UART4 UART8 UART7 OTG2
|
|
|
|
# USB
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
PA9 VBUS INPUT OPENDRAIN
|
|
|
|
# pins for SWD debugging
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# telem1
|
|
PD5 USART2_TX USART2
|
|
PA3 USART2_RX USART2
|
|
PD4 USART2_RTS USART2
|
|
PD3 USART2_CTS USART2
|
|
|
|
# telem2
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
PD12 USART3_RTS USART3
|
|
PD11 USART3_CTS USART3
|
|
|
|
# GPS1
|
|
PB6 USART1_TX USART1
|
|
PB7 USART1_RX USART1
|
|
|
|
# GPS2
|
|
PH13 UART4_TX UART4
|
|
PH14 UART4_RX UART4
|
|
|
|
# USART6 is for IOMCU
|
|
PC6 USART6_TX USART6
|
|
PC7 USART6_RX USART6
|
|
IOMCU_UART USART6
|
|
|
|
# DEBUG
|
|
PE8 UART7_TX UART7
|
|
PE7 UART7_RX UART7
|
|
|
|
# SBUS/CRSF
|
|
PE1 UART8_TX UART8
|
|
PE0 UART8_RX UART8
|
|
define DEFAULT_SERIAL5_PROTOCOL SerialProtocol_RCIN
|
|
|
|
# Ethernet
|
|
PC1 ETH_MDC ETH1
|
|
PA2 ETH_MDIO ETH1
|
|
PC4 ETH_RMII_RXD0 ETH1
|
|
PC5 ETH_RMII_RXD1 ETH1
|
|
PG13 ETH_RMII_TXD0 ETH1
|
|
PG12 ETH_RMII_TXD1 ETH1
|
|
PB11 ETH_RMII_TX_EN ETH1
|
|
PA7 ETH_RMII_CRS_DV ETH1
|
|
PA1 ETH_RMII_REF_CLK ETH1
|
|
|
|
define BOARD_PHY_ID MII_LAN8742A_ID
|
|
define BOARD_PHY_RMII
|
|
|
|
# ADC
|
|
PA0 SCALED1_V3V3 ADC1 SCALE(2)
|
|
PA4 SCALED2_V3V3 ADC1 SCALE(2)
|
|
PB0 SCALED3_V3V3 ADC1 SCALE(2)
|
|
PC0 SCALED4_V3V3 ADC1 SCALE(2)
|
|
PB1 VDD_5V_SENS ADC1 SCALE(2.02)
|
|
|
|
PF13 ADC1_6V6 ADC2 SCALE(2)
|
|
PF12 ADC1_3V3 ADC1 SCALE(1)
|
|
|
|
# SPI1 - IMU3 ICM20689
|
|
PA5 SPI1_SCK SPI1
|
|
PB5 SPI1_MOSI SPI1
|
|
PG9 SPI1_MISO SPI1
|
|
PI9 ICM20689_CS CS
|
|
|
|
# SPI2 -BARO1 BMP581
|
|
PI1 SPI2_SCK SPI2
|
|
PI2 SPI2_MISO SPI2
|
|
PI3 SPI2_MOSI SPI2
|
|
PH5 BMP_581_CS CS
|
|
PA10 DRDY6_BMP581 INPUT
|
|
|
|
# SPI3 -IMU1 BMI088
|
|
PB2 SPI3_MOSI SPI3
|
|
PC10 SPI3_SCK SPI3
|
|
PC11 SPI3_MISO SPI3
|
|
PI4 BMI088_A_CS CS
|
|
PI8 BMI088_G_CS CS
|
|
DRDY1_BMI088_ACC1 INPUT
|
|
DRDY2_BMI088_ACC2 INPUT
|
|
DRDY3_BMI088_GYRO1 INPUT
|
|
DRDY4_BMI088_GYRO2 INPUT
|
|
|
|
# SPI4 - IMU2
|
|
PE12 SPI4_SCK SPI4
|
|
PE13 SPI4_MISO SPI4
|
|
PE14 SPI4_MOSI SPI4
|
|
PH15 ICM_42688_CS CS
|
|
PF3 DRDY5_ICM_42688 INPUT
|
|
|
|
# SPI5 - FRAM
|
|
PF7 SPI5_SCK SPI5
|
|
PH7 SPI5_MISO SPI5
|
|
PF11 SPI5_MOSI SPI5
|
|
PG7 FRAM_CS CS
|
|
|
|
# SPI6 - external1
|
|
PB3 SPI6_SCK SPI6
|
|
PA6 SPI6_MISO SPI6
|
|
PG14 SPI6_MOSI SPI6
|
|
PC2 EXT1_CS CS
|
|
PC3 EXT2_CS CS
|
|
|
|
# PWM output pins
|
|
PI0 TIM5_CH4 TIM5 PWM(1) GPIO(50) BIDIR
|
|
PH12 TIM5_CH3 TIM5 PWM(2) GPIO(51)
|
|
PH11 TIM5_CH2 TIM5 PWM(3) GPIO(52) BIDIR
|
|
PH10 TIM5_CH1 TIM5 PWM(4) GPIO(53)
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
PH6 TIM12_CH1 TIM12 PWM(7) GPIO(56) NODMA
|
|
PH9 TIM12_CH2 TIM12 PWM(8) GPIO(57) NODMA
|
|
|
|
# PWM output for buzzer
|
|
PF9 TIM14_CH1 TIM14 GPIO(77) ALARM
|
|
|
|
# CAN bus
|
|
PD0 CAN1_RX CAN1
|
|
PD1 CAN1_TX CAN1
|
|
|
|
PB12 CAN2_RX CAN2
|
|
PB13 CAN2_TX CAN2
|
|
|
|
# control for silent (no output) for CAN
|
|
PC12 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(70)
|
|
PG2 GPIO_CAN2_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(71)
|
|
|
|
# I2C buses
|
|
|
|
# I2C1, GPS+MAG
|
|
PB9 I2C1_SDA I2C1
|
|
PB8 I2C1_SCL I2C1
|
|
|
|
# I2C2, GPS2+MAG
|
|
PF1 I2C2_SCL I2C2
|
|
PF0 I2C2_SDA I2C2
|
|
|
|
# I2C3
|
|
PA8 I2C3_SCL I2C3
|
|
PH8 I2C3_SDA I2C3
|
|
|
|
# I2C4 (ICP20100)
|
|
PF14 I2C4_SCL I2C4
|
|
PF15 I2C4_SDA I2C4
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C3 I2C4 I2C1 I2C2
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
# power enable pins
|
|
PG3 VDD_3V3_SD_CARD_EN OUTPUT HIGH
|
|
PG6 VDD_3V3_IMU_EN OUTPUT HIGH
|
|
PE6 VDD_3V3_IMU2_EN OUTPUT HIGH
|
|
PD15 VDD_I2C_BATT1_EN OUTPUT HIGH
|
|
PF10 VDD_I2C_CAN_EN OUTPUT HIGH
|
|
|
|
# start peripheral power on
|
|
PE2 HIPOWER_EN OUTPUT HIGH
|
|
PD2 PERIPH_EN OUTPUT HIGH
|
|
|
|
# power sensing
|
|
PA15 PERIPH_OC INPUT PULLUP
|
|
PE10 HIPOWER_OC INPUT PULLUP
|
|
|
|
#Not in use, but reserved
|
|
PB10 VDD_BRICKA_nVALID INPUT PULLUP
|
|
PE15 VDD_BRICKB_nVALID INPUT PULLUP
|
|
PE11 VDD_BRICKC_nVALID INPUT PULLUP
|
|
|
|
# microSD support
|
|
PD6 SDMMC2_CK SDMMC2
|
|
PD7 SDMMC2_CMD SDMMC2
|
|
PB14 SDMMC2_D0 SDMMC2
|
|
PB15 SDMMC2_D1 SDMMC2
|
|
PG11 SDMMC2_D2 SDMMC2
|
|
PB4 SDMMC2_D3 SDMMC2
|
|
define FATFS_HAL_DEVICE SDCD2
|
|
|
|
# ID pins
|
|
PG0 HW_VER_REV_DRIVE OUTPUT LOW
|
|
|
|
# safety
|
|
PD10 LED_SAFETY OUTPUT
|
|
PF5 SAFETY_IN INPUT PULLDOWN
|
|
|
|
# heater
|
|
PG15 HEATER_EN OUTPUT LOW GPIO(80)
|
|
define HAL_HEATER_GPIO_PIN 80
|
|
|
|
# Setup the IMU heater
|
|
define HAL_HAVE_IMU_HEATER 1
|
|
define HAL_IMU_TEMP_DEFAULT 45
|
|
define HAL_IMUHEAT_P_DEFAULT 50
|
|
define HAL_IMUHEAT_I_DEFAULT 0.07
|
|
|
|
# LED
|
|
PE3 LED_R1 OUTPUT OPENDRAIN HIGH GPIO(0)
|
|
PE4 LED_G1 OUTPUT OPENDRAIN LOW GPIO(1)
|
|
PE5 LED_B1 OUTPUT OPENDRAIN HIGH GPIO(2)
|
|
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
define HAL_GPIO_B_LED_PIN 1
|
|
define HAL_GPIO_C_LED_PIN 2
|
|
|
|
# use pixracer style 3-LED indicators
|
|
define HAL_HAVE_PIXRACER_LED
|
|
|
|
define HAL_GPIO_LED_ON 0
|
|
|
|
# compass
|
|
#define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
# compass
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
define HAL_SKIP_AUTO_INTERNAL_I2C_PROBE
|
|
define HAL_COMPASS_DISABLE_IST8310_INTERNAL_PROBE
|
|
define AP_COMPASS_IST8310_DEFAULT_ROTATION ROTATION_ROLL_180_YAW_90
|
|
COMPASS IST8310 I2C:0:0x0E false ROTATION_ROLL_90_YAW_90
|
|
COMPASS IST8310 I2C:ALL_EXTERNAL:0x0E true ROTATION_ROLL_180_YAW_90
|
|
|
|
# IMU devices for SULILGH7_P1
|
|
SPIDEV bmi088_a SPI3 DEVID2 BMI088_A_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV bmi088_g SPI3 DEVID1 BMI088_G_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV icm42688 SPI4 DEVID2 ICM_42688_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV icm20689 SPI1 DEVID2 ICM20689_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV bmp581 SPI2 DEVID1 BMP_581_CS MODE3 7.5*MHZ 12*MHZ
|
|
|
|
SPIDEV ramtron SPI5 DEVID1 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
|
|
# SULILGH7_P1 3 IMUs
|
|
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_NONE
|
|
IMU Invensensev3 SPI:icm42688 ROTATION_YAW_90
|
|
IMU Invensense SPI:icm20689 ROTATION_PITCH_180_YAW_90
|
|
|
|
define HAL_INS_HIGHRES_SAMPLE 7
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 7
|
|
|
|
# barometers
|
|
BARO BMP581 SPI:bmp581
|
|
BARO ICP201XX I2C:1:0x63
|
|
|
|
# enable RAMTROM parameter storage
|
|
define HAL_STORAGE_SIZE 32768
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# allow to have have a dedicated safety switch pin
|
|
define HAL_HAVE_SAFETY_SWITCH 1
|
|
|
|
DMA_PRIORITY TIM5* TIM4* SPI1* SPI2* SPI3* SDMMC* USART6* ADC* UART* USART*
|
|
|
|
# enable FAT filesystem support (needs a microSD defined via SDMMC)
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# enable DFU reboot for installing bootloader
|
|
# note that if firmware is build with --secure-bl then DFU is
|
|
# disabled
|
|
ENABLE_DFU_BOOT 1
|
|
|
|
# build ABIN for flash-from-bootloader support:
|
|
env BUILD_ABIN True
|
|
|
|
ROMFS io_firmware.bin Tools/IO_Firmware/iofirmware_f103_8MHz_lowpolh.bin
|
|
ROMFS io_firmware_dshot.bin Tools/IO_Firmware/iofirmware_f103_8MHz_dshot_lowpolh.bin
|
|
|
|
define HAL_WITH_IO_MCU_DSHOT 1
|