ardupilot/ArduPlane/radio.cpp

388 lines
13 KiB
C++

#include "Plane.h"
//Function that will read the radio data, limit servos and trigger a failsafe
// ----------------------------------------------------------------------------
/*
allow for runtime change of control channel ordering
*/
void Plane::set_control_channels(void)
{
if (g.rudder_only) {
// in rudder only mode the roll and rudder channels are the
// same.
channel_roll = RC_Channels::rc_channel(rcmap.yaw()-1);
} else {
channel_roll = RC_Channels::rc_channel(rcmap.roll()-1);
}
channel_pitch = RC_Channels::rc_channel(rcmap.pitch()-1);
channel_throttle = RC_Channels::rc_channel(rcmap.throttle()-1);
channel_rudder = RC_Channels::rc_channel(rcmap.yaw()-1);
// set rc channel ranges
channel_roll->set_angle(SERVO_MAX);
channel_pitch->set_angle(SERVO_MAX);
channel_rudder->set_angle(SERVO_MAX);
if (!have_reverse_thrust()) {
// normal operation
channel_throttle->set_range(100);
} else {
// reverse thrust
if (have_reverse_throttle_rc_option) {
// when we have a reverse throttle RC option setup we use throttle
// as a range, and rely on the RC switch to get reverse thrust
channel_throttle->set_range(100);
} else {
channel_throttle->set_angle(100);
}
SRV_Channels::set_angle(SRV_Channel::k_throttle, 100);
SRV_Channels::set_angle(SRV_Channel::k_throttleLeft, 100);
SRV_Channels::set_angle(SRV_Channel::k_throttleRight, 100);
}
if (!arming.is_armed() && arming.arming_required() == AP_Arming::Required::YES_MIN_PWM) {
SRV_Channels::set_safety_limit(SRV_Channel::k_throttle, have_reverse_thrust()?SRV_Channel::SRV_CHANNEL_LIMIT_TRIM:SRV_Channel::SRV_CHANNEL_LIMIT_MIN);
}
if (!quadplane.enable) {
// setup correct scaling for ESCs like the UAVCAN PX4ESC which
// take a proportion of speed. For quadplanes we use AP_Motors
// scaling
g2.servo_channels.set_esc_scaling_for(SRV_Channel::k_throttle);
}
}
/*
initialise RC input channels
*/
void Plane::init_rc_in()
{
// set rc dead zones
channel_roll->set_default_dead_zone(30);
channel_pitch->set_default_dead_zone(30);
channel_rudder->set_default_dead_zone(30);
channel_throttle->set_default_dead_zone(30);
}
/*
initialise RC output for main channels. This is done early to allow
for BRD_SAFETYENABLE=0 and early servo control
*/
void Plane::init_rc_out_main()
{
/*
change throttle trim to minimum throttle. This prevents a
configuration error where the user sets CH3_TRIM incorrectly and
the motor may start on power up
*/
if (!have_reverse_thrust()) {
SRV_Channels::set_trim_to_min_for(SRV_Channel::k_throttle);
}
SRV_Channels::set_failsafe_limit(SRV_Channel::k_aileron, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_failsafe_limit(SRV_Channel::k_elevator, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_failsafe_limit(SRV_Channel::k_throttle, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
SRV_Channels::set_failsafe_limit(SRV_Channel::k_rudder, SRV_Channel::SRV_CHANNEL_LIMIT_TRIM);
// setup PX4 to output the min throttle when safety off if arming
// is setup for min on disarm
if (arming.arming_required() == AP_Arming::Required::YES_MIN_PWM) {
SRV_Channels::set_safety_limit(SRV_Channel::k_throttle, have_reverse_thrust()?SRV_Channel::SRV_CHANNEL_LIMIT_TRIM:SRV_Channel::SRV_CHANNEL_LIMIT_MIN);
}
}
/*
initialise RC output channels for aux channels
*/
void Plane::init_rc_out_aux()
{
SRV_Channels::enable_aux_servos();
SRV_Channels::cork();
servos_output();
// setup PWM values to send if the FMU firmware dies
// allows any VTOL motors to shut off
SRV_Channels::setup_failsafe_trim_all_non_motors();
}
/*
check for pilot input on rudder stick for arming/disarming
*/
void Plane::rudder_arm_disarm_check()
{
AP_Arming::RudderArming arming_rudder = arming.get_rudder_arming_type();
if (arming_rudder == AP_Arming::RudderArming::IS_DISABLED) {
//parameter disallows rudder arming/disabling
return;
}
// if throttle is not down, then pilot cannot rudder arm/disarm
if (get_throttle_input() != 0){
rudder_arm_timer = 0;
return;
}
// if not in a manual throttle mode and not in CRUISE or FBWB
// modes then disallow rudder arming/disarming
if (auto_throttle_mode &&
(control_mode != CRUISE && control_mode != FLY_BY_WIRE_B)) {
rudder_arm_timer = 0;
return;
}
if (!arming.is_armed()) {
// when not armed, full right rudder starts arming counter
if (channel_rudder->get_control_in() > 4000) {
uint32_t now = millis();
if (rudder_arm_timer == 0 ||
now - rudder_arm_timer < 3000) {
if (rudder_arm_timer == 0) {
rudder_arm_timer = now;
}
} else {
//time to arm!
arm_motors(AP_Arming::Method::RUDDER);
rudder_arm_timer = 0;
}
} else {
// not at full right rudder
rudder_arm_timer = 0;
}
} else if ((arming_rudder == AP_Arming::RudderArming::ARMDISARM) && !is_flying()) {
// when armed and not flying, full left rudder starts disarming counter
if (channel_rudder->get_control_in() < -4000) {
uint32_t now = millis();
if (rudder_arm_timer == 0 ||
now - rudder_arm_timer < 3000) {
if (rudder_arm_timer == 0) {
rudder_arm_timer = now;
}
} else {
//time to disarm!
disarm_motors();
rudder_arm_timer = 0;
}
} else {
// not at full left rudder
rudder_arm_timer = 0;
}
}
}
void Plane::read_radio()
{
if (!rc().read_input()) {
control_failsafe();
return;
}
if(!failsafe.rc_failsafe)
{
failsafe.AFS_last_valid_rc_ms = millis();
}
failsafe.last_valid_rc_ms = millis();
if (control_mode == TRAINING) {
// in training mode we don't want to use a deadzone, as we
// want manual pass through when not exceeding attitude limits
channel_roll->recompute_pwm_no_deadzone();
channel_pitch->recompute_pwm_no_deadzone();
channel_throttle->recompute_pwm_no_deadzone();
channel_rudder->recompute_pwm_no_deadzone();
}
control_failsafe();
if (g.throttle_nudge && channel_throttle->get_control_in() > 50 && geofence_stickmixing()) {
float nudge = (channel_throttle->get_control_in() - 50) * 0.02f;
if (ahrs.airspeed_sensor_enabled()) {
airspeed_nudge_cm = (aparm.airspeed_max * 100 - aparm.airspeed_cruise_cm) * nudge;
} else {
throttle_nudge = (aparm.throttle_max - aparm.throttle_cruise) * nudge;
}
} else {
airspeed_nudge_cm = 0;
throttle_nudge = 0;
}
rudder_arm_disarm_check();
// potentially swap inputs for tailsitters
quadplane.tailsitter_check_input();
// check for transmitter tuning changes
tuning.check_input(control_mode);
}
int16_t Plane::rudder_input(void)
{
if (g.rudder_only != 0) {
// in rudder only mode we discard rudder input and get target
// attitude from the roll channel.
return 0;
}
if ((g2.flight_options & FlightOptions::DIRECT_RUDDER_ONLY) &&
!(control_mode == MANUAL || control_mode == STABILIZE || control_mode == ACRO)) {
// the user does not want any input except in these modes
return 0;
}
if (stick_mixing_enabled()) {
return channel_rudder->get_control_in();
}
return 0;
}
void Plane::control_failsafe()
{
if (millis() - failsafe.last_valid_rc_ms > 1000 || rc_failsafe_active()) {
// we do not have valid RC input. Set all primary channel
// control inputs to the trim value and throttle to min
channel_roll->set_radio_in(channel_roll->get_radio_trim());
channel_pitch->set_radio_in(channel_pitch->get_radio_trim());
channel_rudder->set_radio_in(channel_rudder->get_radio_trim());
// note that we don't set channel_throttle->radio_in to radio_trim,
// as that would cause throttle failsafe to not activate
channel_roll->set_control_in(0);
channel_pitch->set_control_in(0);
channel_rudder->set_control_in(0);
switch (control_mode) {
case QSTABILIZE:
case QHOVER:
case QLOITER:
case QLAND: // throttle is ignored, but reset anyways
case QRTL: // throttle is ignored, but reset anyways
case QAUTOTUNE:
if (quadplane.available() && quadplane.motors->get_desired_spool_state() > AP_Motors::DESIRED_GROUND_IDLE) {
// set half throttle to avoid descending at maximum rate, still has a slight descent due to throttle deadzone
channel_throttle->set_control_in(channel_throttle->get_range() / 2);
break;
}
FALLTHROUGH;
default:
channel_throttle->set_control_in(0);
break;
}
}
if(g.throttle_fs_enabled == 0)
return;
if (g.throttle_fs_enabled) {
if (rc_failsafe_active()) {
// we detect a failsafe from radio
// throttle has dropped below the mark
failsafe.throttle_counter++;
if (failsafe.throttle_counter == 10) {
gcs().send_text(MAV_SEVERITY_WARNING, "Throttle failsafe on");
failsafe.rc_failsafe = true;
AP_Notify::flags.failsafe_radio = true;
}
if (failsafe.throttle_counter > 10) {
failsafe.throttle_counter = 10;
}
}else if(failsafe.throttle_counter > 0) {
// we are no longer in failsafe condition
// but we need to recover quickly
failsafe.throttle_counter--;
if (failsafe.throttle_counter > 3) {
failsafe.throttle_counter = 3;
}
if (failsafe.throttle_counter == 1) {
gcs().send_text(MAV_SEVERITY_WARNING, "Throttle failsafe off");
} else if(failsafe.throttle_counter == 0) {
failsafe.rc_failsafe = false;
AP_Notify::flags.failsafe_radio = false;
}
}
}
}
bool Plane::trim_radio()
{
if (failsafe.rc_failsafe) {
// can't trim if we don't have valid input
return false;
}
int16_t trim_roll_range = (channel_roll->get_radio_max() - channel_roll->get_radio_min())/5;
int16_t trim_pitch_range = (channel_pitch->get_radio_max() - channel_pitch->get_radio_min())/5;
if (channel_roll->get_radio_in() < channel_roll->get_radio_min()+trim_roll_range ||
channel_roll->get_radio_in() > channel_roll->get_radio_max()-trim_roll_range ||
channel_pitch->get_radio_in() < channel_pitch->get_radio_min()+trim_pitch_range ||
channel_pitch->get_radio_in() > channel_pitch->get_radio_max()-trim_pitch_range) {
// don't trim for extreme values - if we attempt to trim so
// there is less than 20 percent range left then assume the
// sticks are not properly centered. This also prevents
// problems with starting APM with the TX off
return false;
}
// trim main surfaces
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_aileron);
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_elevator);
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_rudder);
// trim elevons
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_elevon_left);
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_elevon_right);
// trim vtail
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_vtail_left);
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_vtail_right);
if (SRV_Channels::get_output_scaled(SRV_Channel::k_rudder) == 0) {
// trim differential spoilers if no rudder input
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_dspoilerLeft1);
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_dspoilerLeft2);
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_dspoilerRight1);
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_dspoilerRight2);
}
if (SRV_Channels::get_output_scaled(SRV_Channel::k_flap_auto) == 0 &&
SRV_Channels::get_output_scaled(SRV_Channel::k_flap) == 0) {
// trim flaperons if no flap input
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_flaperon_left);
SRV_Channels::set_trim_to_servo_out_for(SRV_Channel::k_flaperon_right);
}
// now save input trims, as these have been moved to the outputs
channel_roll->set_and_save_trim();
channel_pitch->set_and_save_trim();
channel_rudder->set_and_save_trim();
return true;
}
/*
return true if throttle level is below throttle failsafe threshold
or RC input is invalid
*/
bool Plane::rc_failsafe_active(void) const
{
if (!g.throttle_fs_enabled) {
return false;
}
if (millis() - failsafe.last_valid_rc_ms > 1000) {
// we haven't had a valid RC frame for 1 seconds
return true;
}
if (channel_throttle->get_reverse()) {
return channel_throttle->get_radio_in() >= g.throttle_fs_value;
}
return channel_throttle->get_radio_in() <= g.throttle_fs_value;
}