ardupilot/ArduCopter/radio.pde

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-

// Function that will read the radio data, limit servos and trigger a failsafe
// ----------------------------------------------------------------------------

static void default_dead_zones()
{
    g.rc_1.set_default_dead_zone(30);
    g.rc_2.set_default_dead_zone(30);
#if FRAME_CONFIG == HELI_FRAME
    g.rc_3.set_default_dead_zone(10);
    g.rc_4.set_default_dead_zone(15);
#else
    g.rc_3.set_default_dead_zone(30);
    g.rc_4.set_default_dead_zone(40);
#endif
    g.rc_6.set_default_dead_zone(0);
}

static void init_rc_in()
{
    // set rc channel ranges
    g.rc_1.set_angle(ROLL_PITCH_INPUT_MAX);
    g.rc_2.set_angle(ROLL_PITCH_INPUT_MAX);
#if FRAME_CONFIG == HELI_FRAME
    // we do not want to limit the movment of the heli's swash plate
    g.rc_3.set_range(0, 1000);
#else
    g.rc_3.set_range(g.throttle_min, g.throttle_max);
#endif
    g.rc_4.set_angle(4500);

    g.rc_1.set_type(RC_CHANNEL_TYPE_ANGLE_RAW);
    g.rc_2.set_type(RC_CHANNEL_TYPE_ANGLE_RAW);
    g.rc_4.set_type(RC_CHANNEL_TYPE_ANGLE_RAW);

    //set auxiliary ranges
    g.rc_5.set_range(0,1000);
    g.rc_6.set_range(0,1000);
    g.rc_7.set_range(0,1000);
    g.rc_8.set_range(0,1000);

#if CONFIG_HAL_BOARD == HAL_BOARD_PX4
    update_aux_servo_function(&g.rc_5, &g.rc_6, &g.rc_7, &g.rc_8, &g.rc_9, &g.rc_10, &g.rc_11, &g.rc_12);
#elif MOUNT == ENABLED
    update_aux_servo_function(&g.rc_5, &g.rc_6, &g.rc_7, &g.rc_8, &g.rc_10, &g.rc_11);
#endif

    // set default dead zones
    default_dead_zones();
}

 // init_rc_out -- initialise motors and check if pilot wants to perform ESC calibration
static void init_rc_out()
{
    motors.set_update_rate(g.rc_speed);
    motors.set_frame_orientation(g.frame_orientation);
    motors.Init();                                              // motor initialisation
    motors.set_min_throttle(g.throttle_min);

    for(uint8_t i = 0; i < 5; i++) {
        delay(20);
        read_radio();
    }

    // we want the input to be scaled correctly
    g.rc_3.set_range_out(0,1000);

    // full throttle means to enter ESC calibration
    if(g.rc_3.control_in >= (g.throttle_max - 50)) {
        if(g.esc_calibrate == 0) {
            // we will enter esc_calibrate mode on next reboot
            g.esc_calibrate.set_and_save(1);
            // display message on console
            cliSerial->printf_P(PSTR("Entering ESC Calibration: please restart APM.\n"));
            // turn on esc calibration notification
            AP_Notify::flags.esc_calibration = true;
            // block until we restart
            while(1) { delay(5); }
        }else{
            cliSerial->printf_P(PSTR("ESC Calibration active: passing throttle through to ESCs.\n"));
            // clear esc flag
            g.esc_calibrate.set_and_save(0);
            // pass through user throttle to escs
            init_esc();
        }
    }else{
        // did we abort the calibration?
        if(g.esc_calibrate == 1)
            g.esc_calibrate.set_and_save(0);
    }

    // enable output to motors
    pre_arm_rc_checks();
    if (ap.pre_arm_rc_check) {
        output_min();
    }

#if TOY_EDF == ENABLED
    // add access to CH8 and CH6
    APM_RC.enable_out(CH_8);
    APM_RC.enable_out(CH_6);
#endif
}

// output_min - enable and output lowest possible value to motors
void output_min()
{
    // enable motors
    motors.enable();
    motors.output_min();
}

#define FAILSAFE_RADIO_TIMEOUT_MS 2000       // 2 seconds
static void read_radio()
{
    static uint32_t last_update = 0;
    if (hal.rcin->valid_channels() > 0) {
        last_update = millis();
        ap.new_radio_frame = true;
        uint16_t periods[8];
        hal.rcin->read(periods,8);
        g.rc_1.set_pwm(periods[rcmap.roll()-1]);
        g.rc_2.set_pwm(periods[rcmap.pitch()-1]);

        set_throttle_and_failsafe(periods[rcmap.throttle()-1]);

        g.rc_4.set_pwm(periods[rcmap.yaw()-1]);
        g.rc_5.set_pwm(periods[4]);
        g.rc_6.set_pwm(periods[5]);
        g.rc_7.set_pwm(periods[6]);
        g.rc_8.set_pwm(periods[7]);
    }else{
        uint32_t elapsed = millis() - last_update;
        // turn on throttle failsafe if no update from ppm encoder for 2 seconds
        if ((elapsed >= FAILSAFE_RADIO_TIMEOUT_MS)
                && g.failsafe_throttle && motors.armed() && !failsafe.radio) {
            Log_Write_Error(ERROR_SUBSYSTEM_RADIO, ERROR_CODE_RADIO_LATE_FRAME);
            set_failsafe_radio(true);
        }
    }
}

#define FS_COUNTER 3        // radio failsafe kicks in after 3 consecutive throttle values below failsafe_throttle_value
static void set_throttle_and_failsafe(uint16_t throttle_pwm)
{
    // if failsafe not enabled pass through throttle and exit
    if(g.failsafe_throttle == FS_THR_DISABLED) {
        g.rc_3.set_pwm(throttle_pwm);
        return;
    }

    //check for low throttle value
    if (throttle_pwm < (uint16_t)g.failsafe_throttle_value) {

        // if we are already in failsafe or motors not armed pass through throttle and exit
        if (failsafe.radio || !motors.armed()) {
            g.rc_3.set_pwm(throttle_pwm);
            return;
        }

        // check for 3 low throttle values
        // Note: we do not pass through the low throttle until 3 low throttle values are recieved
        failsafe.radio_counter++;
        if( failsafe.radio_counter >= FS_COUNTER ) {
            failsafe.radio_counter = FS_COUNTER;  // check to ensure we don't overflow the counter
            set_failsafe_radio(true);
            g.rc_3.set_pwm(throttle_pwm);   // pass through failsafe throttle
        }
    }else{
        // we have a good throttle so reduce failsafe counter
        failsafe.radio_counter--;
        if( failsafe.radio_counter <= 0 ) {
            failsafe.radio_counter = 0;   // check to ensure we don't underflow the counter

            // disengage failsafe after three (nearly) consecutive valid throttle values
            if (failsafe.radio) {
                set_failsafe_radio(false);
            }
        }
        // pass through throttle
        g.rc_3.set_pwm(throttle_pwm);
    }
}

static void trim_radio()
{
    for (uint8_t i = 0; i < 30; i++) {
        read_radio();
    }

    g.rc_1.trim();      // roll
    g.rc_2.trim();      // pitch
    g.rc_4.trim();      // yaw

    g.rc_1.save_eeprom();
    g.rc_2.save_eeprom();
    g.rc_4.save_eeprom();
}