mirror of https://github.com/ArduPilot/ardupilot
164 lines
3.5 KiB
Plaintext
164 lines
3.5 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# for Holybro KakuteH7 hardware.
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1048
|
|
|
|
# crystal frequency, setup to use external oscillator
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 12
|
|
define CH_CFG_ST_RESOLUTION 16
|
|
|
|
# leave 1 sectors free
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
# use last 2 pages for flash storage
|
|
# H743 has 16 pages of 128k each
|
|
STORAGE_FLASH_PAGE 14
|
|
define HAL_STORAGE_SIZE 32768
|
|
|
|
# one I2C bus
|
|
I2C_ORDER I2C1
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 EMPTY USART6 UART7
|
|
|
|
# buzzer
|
|
PC13 BUZZER OUTPUT LOW PULLDOWN GPIO(80)
|
|
define HAL_BUZZER_PIN 80
|
|
|
|
|
|
|
|
# PA10 IO-debug-console
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# SPI1 for SDCard
|
|
PA4 SDCARD_CS CS
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
PA3 SDCARD_DETECT INPUT
|
|
|
|
# SPI2 for MAX7456 OSD
|
|
PB12 MAX7456_CS CS
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
# SPI4 for mpu6000
|
|
PE4 mpu6000_CS CS
|
|
PE2 SPI4_SCK SPI4
|
|
PE5 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
# I2C1 for baro
|
|
PB6 I2C1_SCL I2C1
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
PA8 VBUS INPUT
|
|
|
|
# define default battery setup (note external current sensor required)
|
|
define HAL_BATT_VOLT_PIN 10
|
|
define HAL_BATT_CURR_PIN 11
|
|
define HAL_BATT_VOLT_SCALE 11.0
|
|
define HAL_BATT_CURR_SCALE 59.5
|
|
|
|
PC5 RSSI_ADC ADC1
|
|
define BOARD_RSSI_ANA_PIN 8
|
|
|
|
PC2 LED0 OUTPUT LOW
|
|
|
|
# USART1
|
|
PA9 USART1_TX USART1
|
|
PA10 USART1_RX USART1
|
|
|
|
# USART2
|
|
PD5 USART2_TX USART2 NODMA
|
|
PD6 USART2_RX USART2 NODMA
|
|
|
|
# USART3 (GPS)
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
|
|
# UART4 (GPS2)
|
|
PD0 UART4_RX UART4 NODMA
|
|
PD1 UART4_TX UART4 NODMA
|
|
|
|
# RC input defaults to timer capture
|
|
PC7 TIM3_CH2 TIM3 RCININT PULLDOWN
|
|
|
|
# alternative config using USART for protocols
|
|
# like FPort
|
|
PC7 USART6_RX USART6 NODMA ALT(1)
|
|
PC6 USART6_TX USART6 NODMA
|
|
|
|
# UART7 USED BY ESC FROM ORIGINAL DESIGN
|
|
PE7 UART7_RX UART7
|
|
PE8 UART7_TX UART7
|
|
|
|
# Motors
|
|
PB0 TIM1_CH2N TIM1 PWM(1) GPIO(50)
|
|
PB1 TIM1_CH3N TIM1 PWM(2) GPIO(51)
|
|
PB3 TIM2_CH2 TIM2 PWM(3) GPIO(52)
|
|
PB10 TIM2_CH3 TIM2 PWM(4) GPIO(53)
|
|
PA0 TIM5_CH1 TIM5 PWM(5) GPIO(54)
|
|
PA2 TIM5_CH3 TIM5 PWM(6) GPIO(55)
|
|
PC8 TIM8_CH3 TIM8 PWM(7) GPIO(56)
|
|
PC9 TIM8_CH4 TIM8 PWM(8) GPIO(57)
|
|
|
|
# LED strip
|
|
PD12 TIM4_CH1 TIM4 PWM(9) GPIO(58)
|
|
|
|
DMA_PRIORITY TIM1* TIM2* TIM5* TIM3* SPI4* SPI1*
|
|
DMA_NOSHARE SPI1*
|
|
|
|
# spi devices
|
|
SPIDEV mpu6000 SPI4 DEVID1 mpu6000_CS MODE3 1*MHZ 4*MHZ
|
|
SPIDEV icm42688 SPI4 DEVID1 mpu6000_CS MODE3 1*MHZ 16*MHZ
|
|
SPIDEV bmi270 SPI4 DEVID1 mpu6000_CS MODE3 1*MHZ 10*MHZ # Clock is 100Mhz so highest clock <= 10Mhz is 100Mhz/16
|
|
SPIDEV sdcard SPI1 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ
|
|
SPIDEV osd SPI2 DEVID4 MAX7456_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
# bluetooth power switch, turn it off to prevent rf interference
|
|
PE13 EVENT_OUT OUTPUT LOW PUSHPULL GPIO(82)
|
|
define RELAY3_PIN_DEFAULT 82
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
# external compass types
|
|
define ALLOW_ARM_NO_COMPASS
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
# one IMU
|
|
IMU Invensense SPI:mpu6000 ROTATION_YAW_180
|
|
IMU Invensensev3 SPI:icm42688 ROTATION_ROLL_180_YAW_270
|
|
IMU BMI270 SPI:bmi270 ROTATION_ROLL_180_YAW_270
|
|
|
|
# one BARO
|
|
BARO BMP280 I2C:0:0x76
|
|
BARO SPL06 I2C:0:0x76
|
|
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# setup for OSD
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
|
|
|
define DEFAULT_NTF_LED_TYPES 257
|