Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
ardupilot/ArduCopter/mode_autotune.cpp

1524 lines
66 KiB
C++
Raw Blame History

#include "Copter.h"
#if AUTOTUNE_ENABLED == ENABLED
/*
* Init and run calls for autotune flight mode
*
* Instructions:
* 1) Set up one flight mode switch position to be AltHold.
* 2) Set the Ch7 Opt or Ch8 Opt to AutoTune to allow you to turn the auto tuning on/off with the ch7 or ch8 switch.
* 3) Ensure the ch7 or ch8 switch is in the LOW position.
* 4) Wait for a calm day and go to a large open area.
* 5) Take off and put the vehicle into AltHold mode at a comfortable altitude.
* 6) Set the ch7/ch8 switch to the HIGH position to engage auto tuning:
* a) You will see it twitch about 20 degrees left and right for a few minutes, then it will repeat forward and back.
* b) Use the roll and pitch stick at any time to reposition the copter if it drifts away (it will use the original PID gains during repositioning and between tests).
* When you release the sticks it will continue auto tuning where it left off.
* c) Move the ch7/ch8 switch into the LOW position at any time to abandon the autotuning and return to the origin PIDs.
* d) Make sure that you do not have any trim set on your transmitter or the autotune may not get the signal that the sticks are centered.
* 7) When the tune completes the vehicle will change back to the original PID gains.
* 8) Put the ch7/ch8 switch into the LOW position then back to the HIGH position to test the tuned PID gains.
* 9) Put the ch7/ch8 switch into the LOW position to fly using the original PID gains.
* 10) If you are happy with the autotuned PID gains, leave the ch7/ch8 switch in the HIGH position, land and disarm to save the PIDs permanently.
* If you DO NOT like the new PIDS, switch ch7/ch8 LOW to return to the original PIDs. The gains will not be saved when you disarm
*
* What it's doing during each "twitch":
* a) invokes 90 deg/sec rate request
* b) records maximum "forward" roll rate and bounce back rate
* c) when copter reaches 20 degrees or 1 second has passed, it commands level
* d) tries to keep max rotation rate between 80% ~ 100% of requested rate (90deg/sec) by adjusting rate P
* e) increases rate D until the bounce back becomes greater than 10% of requested rate (90deg/sec)
* f) decreases rate D until the bounce back becomes less than 10% of requested rate (90deg/sec)
* g) increases rate P until the max rotate rate becomes greater than the request rate (90deg/sec)
* h) invokes a 20deg angle request on roll or pitch
* i) increases stab P until the maximum angle becomes greater than 110% of the requested angle (20deg)
* j) decreases stab P by 25%
*
*/
#define AUTOTUNE_AXIS_BITMASK_ROLL 1
#define AUTOTUNE_AXIS_BITMASK_PITCH 2
#define AUTOTUNE_AXIS_BITMASK_YAW 4
#define AUTOTUNE_PILOT_OVERRIDE_TIMEOUT_MS 500 // restart tuning if pilot has left sticks in middle for 2 seconds
#define AUTOTUNE_TESTING_STEP_TIMEOUT_MS 1000 // timeout for tuning mode's testing step
#define AUTOTUNE_LEVEL_ANGLE_CD 500 // angle which qualifies as level
#define AUTOTUNE_LEVEL_RATE_RP_CD 1000 // rate which qualifies as level for roll and pitch
#define AUTOTUNE_LEVEL_RATE_Y_CD 750 // rate which qualifies as level for yaw
#define AUTOTUNE_REQUIRED_LEVEL_TIME_MS 500 // time we require the copter to be level
#define AUTOTUNE_RD_STEP 0.05f // minimum increment when increasing/decreasing Rate D term
#define AUTOTUNE_RP_STEP 0.05f // minimum increment when increasing/decreasing Rate P term
#define AUTOTUNE_SP_STEP 0.05f // minimum increment when increasing/decreasing Stab P term
#define AUTOTUNE_PI_RATIO_FOR_TESTING 0.1f // I is set 10x smaller than P during testing
#define AUTOTUNE_PI_RATIO_FINAL 1.0f // I is set 1x P after testing
#define AUTOTUNE_YAW_PI_RATIO_FINAL 0.1f // I is set 1x P after testing
#define AUTOTUNE_RD_MAX 0.200f // maximum Rate D value
#define AUTOTUNE_RLPF_MIN 1.0f // minimum Rate Yaw filter value
#define AUTOTUNE_RLPF_MAX 5.0f // maximum Rate Yaw filter value
#define AUTOTUNE_RP_MIN 0.01f // minimum Rate P value
#define AUTOTUNE_RP_MAX 2.0f // maximum Rate P value
#define AUTOTUNE_SP_MAX 20.0f // maximum Stab P value
#define AUTOTUNE_SP_MIN 0.5f // maximum Stab P value
#define AUTOTUNE_RP_ACCEL_MIN 4000.0f // Minimum acceleration for Roll and Pitch
#define AUTOTUNE_Y_ACCEL_MIN 1000.0f // Minimum acceleration for Yaw
#define AUTOTUNE_Y_FILT_FREQ 10.0f // Autotune filter frequency when testing Yaw
#define AUTOTUNE_SUCCESS_COUNT 4 // The number of successful iterations we need to freeze at current gains
#define AUTOTUNE_D_UP_DOWN_MARGIN 0.2f // The margin below the target that we tune D in
#define AUTOTUNE_RD_BACKOFF 1.0f // Rate D gains are reduced to 50% of their maximum value discovered during tuning
#define AUTOTUNE_RP_BACKOFF 1.0f // Rate P gains are reduced to 97.5% of their maximum value discovered during tuning
#define AUTOTUNE_SP_BACKOFF 0.9f // Stab P gains are reduced to 90% of their maximum value discovered during tuning
#define AUTOTUNE_ACCEL_RP_BACKOFF 1.0f // back off from maximum acceleration
#define AUTOTUNE_ACCEL_Y_BACKOFF 1.0f // back off from maximum acceleration
// roll and pitch axes
#define AUTOTUNE_TARGET_ANGLE_RLLPIT_CD 2000 // target angle during TESTING_RATE step that will cause us to move to next step
#define AUTOTUNE_TARGET_RATE_RLLPIT_CDS 9000 // target roll/pitch rate during AUTOTUNE_STEP_TWITCHING step
#define AUTOTUNE_TARGET_MIN_ANGLE_RLLPIT_CD 1000 // minimum target angle during TESTING_RATE step that will cause us to move to next step
#define AUTOTUNE_TARGET_MIN_RATE_RLLPIT_CDS 4500 // target roll/pitch rate during AUTOTUNE_STEP_TWITCHING step
// yaw axis
#define AUTOTUNE_TARGET_ANGLE_YAW_CD 3000 // target angle during TESTING_RATE step that will cause us to move to next step
#define AUTOTUNE_TARGET_RATE_YAW_CDS 9000 // target yaw rate during AUTOTUNE_STEP_TWITCHING step
#define AUTOTUNE_TARGET_MIN_ANGLE_YAW_CD 500 // minimum target angle during TESTING_RATE step that will cause us to move to next step
#define AUTOTUNE_TARGET_MIN_RATE_YAW_CDS 1500 // minimum target yaw rate during AUTOTUNE_STEP_TWITCHING step
// Auto Tune message ids for ground station
#define AUTOTUNE_MESSAGE_STARTED 0
#define AUTOTUNE_MESSAGE_STOPPED 1
#define AUTOTUNE_MESSAGE_SUCCESS 2
#define AUTOTUNE_MESSAGE_FAILED 3
#define AUTOTUNE_MESSAGE_SAVED_GAINS 4
#define AUTOTUNE_ANNOUNCE_INTERVAL_MS 2000
// autotune_init - should be called when autotune mode is selected
bool Copter::ModeAutoTune::init(bool ignore_checks)
{
bool success = true;
switch (mode) {
case FAILED:
// autotune has been run but failed so reset state to uninitialized
mode = UNINITIALISED;
// fall through to restart the tuning
FALLTHROUGH;
case UNINITIALISED:
// autotune has never been run
success = start(false);
if (success) {
// so store current gains as original gains
backup_gains_and_initialise();
// advance mode to tuning
mode = TUNING;
// send message to ground station that we've started tuning
update_gcs(AUTOTUNE_MESSAGE_STARTED);
}
break;
case TUNING:
// we are restarting tuning after the user must have switched ch7/ch8 off so we restart tuning where we left off
success = start(false);
if (success) {
// reset gains to tuning-start gains (i.e. low I term)
load_intra_test_gains();
// write dataflash log even and send message to ground station
Log_Write_Event(DATA_AUTOTUNE_RESTART);
update_gcs(AUTOTUNE_MESSAGE_STARTED);
}
break;
case SUCCESS:
// we have completed a tune and the pilot wishes to test the new gains in the current flight mode
// so simply apply tuning gains (i.e. do not change flight mode)
load_tuned_gains();
Log_Write_Event(DATA_AUTOTUNE_PILOT_TESTING);
break;
}
// only do position hold if starting autotune from LOITER or POSHOLD
use_poshold = (_copter.control_mode == LOITER || _copter.control_mode == POSHOLD);
have_position = false;
return success;
}
// stop - should be called when the ch7/ch8 switch is switched OFF
void Copter::ModeAutoTune::stop()
{
// set gains to their original values
load_orig_gains();
// re-enable angle-to-rate request limits
attitude_control->use_ff_and_input_shaping(true);
// log off event and send message to ground station
update_gcs(AUTOTUNE_MESSAGE_STOPPED);
Log_Write_Event(DATA_AUTOTUNE_OFF);
// Note: we leave the mode as it was so that we know how the autotune ended
// we expect the caller will change the flight mode back to the flight mode indicated by the flight mode switch
}
// start - Initialize autotune flight mode
bool Copter::ModeAutoTune::start(bool ignore_checks)
{
// only allow flip from Stabilize, AltHold, PosHold or Loiter modes
if (_copter.control_mode != STABILIZE && _copter.control_mode != ALT_HOLD &&
_copter.control_mode != LOITER && _copter.control_mode != POSHOLD) {
return false;
}
// ensure throttle is above zero
if (ap.throttle_zero) {
return false;
}
// ensure we are flying
if (!motors->armed() || !ap.auto_armed || ap.land_complete) {
return false;
}
// initialize vertical speeds and leash lengths
pos_control->set_speed_z(-get_pilot_speed_dn(), g.pilot_speed_up);
pos_control->set_accel_z(g.pilot_accel_z);
// initialise position and desired velocity
if (!pos_control->is_active_z()) {
pos_control->set_alt_target_to_current_alt();
pos_control->set_desired_velocity_z(inertial_nav.get_velocity_z());
}
return true;
}
const char *Copter::ModeAutoTune::level_issue_string() const
{
switch (level_problem.issue) {
case LEVEL_ISSUE_NONE:
return "None";
case LEVEL_ISSUE_ANGLE_ROLL:
return "Angle(R)";
case LEVEL_ISSUE_ANGLE_PITCH:
return "Angle(P)";
case LEVEL_ISSUE_ANGLE_YAW:
return "Angle(Y)";
case LEVEL_ISSUE_RATE_ROLL:
return "Rate(R)";
case LEVEL_ISSUE_RATE_PITCH:
return "Rate(P)";
case LEVEL_ISSUE_RATE_YAW:
return "Rate(Y)";
}
return "Bug";
}
void Copter::ModeAutoTune::send_step_string()
{
if (pilot_override) {
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: Paused: Pilot Override Active");
return;
}
switch (step) {
case WAITING_FOR_LEVEL:
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: WFL (%s) (%f > %f)", level_issue_string(), (double)(level_problem.current*0.01f), (double)(level_problem.maximum*0.01f));
return;
case UPDATE_GAINS:
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: UPDATING_GAINS");
return;
case TWITCHING:
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: TWITCHING");
return;
}
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: unknown step");
}
const char *Copter::ModeAutoTune::type_string() const
{
switch (tune_type) {
case RD_UP:
return "Rate D Up";
case RD_DOWN:
return "Rate D Down";
case RP_UP:
return "Rate P Up";
case SP_DOWN:
return "Angle P Down";
case SP_UP:
return "Angle P Up";
}
return "Bug";
}
void Copter::ModeAutoTune::do_gcs_announcements()
{
const uint32_t now = millis();
if (now - announce_time < AUTOTUNE_ANNOUNCE_INTERVAL_MS) {
return;
}
float tune_rp = 0.0f;
float tune_rd = 0.0f;
float tune_sp = 0.0f;
float tune_accel = 0.0f;
char axis_char = '?';
switch (axis) {
case ROLL:
tune_rp = tune_roll_rp;
tune_rd = tune_roll_rd;
tune_sp = tune_roll_sp;
tune_accel = tune_roll_accel;
axis_char = 'R';
break;
case PITCH:
tune_rp = tune_pitch_rp;
tune_rd = tune_pitch_rd;
tune_sp = tune_pitch_sp;
tune_accel = tune_pitch_accel;
axis_char = 'P';
break;
case YAW:
tune_rp = tune_yaw_rp;
tune_rd = tune_yaw_rLPF;
tune_sp = tune_yaw_sp;
tune_accel = tune_yaw_accel;
axis_char = 'Y';
break;
}
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: (%c) %s", axis_char, type_string());
send_step_string();
if (!is_zero(lean_angle)) {
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: lean=%f target=%f", (double)lean_angle, (double)target_angle);
}
if (!is_zero(rotation_rate)) {
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: rotation=%f target=%f", (double)(rotation_rate*0.01f), (double)(target_rate*0.01f));
}
switch (tune_type) {
case RD_UP:
case RD_DOWN:
case RP_UP:
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: p=%f d=%f", (double)tune_rp, (double)tune_rd);
break;
case SP_DOWN:
case SP_UP:
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: p=%f accel=%f", (double)tune_sp, (double)tune_accel);
break;
}
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: success %u/%u", counter, AUTOTUNE_SUCCESS_COUNT);
announce_time = now;
}
// run - runs the autotune flight mode
// should be called at 100hz or more
void Copter::ModeAutoTune::run()
{
float target_roll, target_pitch;
float target_yaw_rate;
int16_t target_climb_rate;
// tell the user what's going on
do_gcs_announcements();
// initialize vertical speeds and acceleration
pos_control->set_speed_z(-get_pilot_speed_dn(), g.pilot_speed_up);
pos_control->set_accel_z(g.pilot_accel_z);
// if not auto armed or motor interlock not enabled set throttle to zero and exit immediately
// this should not actually be possible because of the init() checks
if (!motors->armed() || !ap.auto_armed || !motors->get_interlock()) {
motors->set_desired_spool_state(AP_Motors::DESIRED_SPIN_WHEN_ARMED);
attitude_control->set_throttle_out_unstabilized(0,true,g.throttle_filt);
pos_control->relax_alt_hold_controllers(0.0f);
return;
}
// apply SIMPLE mode transform to pilot inputs
update_simple_mode();
// get pilot desired lean angles
get_pilot_desired_lean_angles(channel_roll->get_control_in(), channel_pitch->get_control_in(), target_roll, target_pitch, _copter.aparm.angle_max);
// get pilot's desired yaw rate
target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->get_control_in());
// get pilot desired climb rate
target_climb_rate = get_pilot_desired_climb_rate(channel_throttle->get_control_in());
// get avoidance adjusted climb rate
target_climb_rate = get_avoidance_adjusted_climbrate(target_climb_rate);
// check for pilot requested take-off - this should not actually be possible because of init() checks
if (ap.land_complete && target_climb_rate > 0) {
// indicate we are taking off
set_land_complete(false);
// clear i term when we're taking off
set_throttle_takeoff();
}
// reset target lean angles and heading while landed
if (ap.land_complete) {
// set motors to spin-when-armed if throttle below deadzone, otherwise full range (but motors will only spin at min throttle)
if (target_climb_rate < 0.0f) {
motors->set_desired_spool_state(AP_Motors::DESIRED_SPIN_WHEN_ARMED);
} else {
motors->set_desired_spool_state(AP_Motors::DESIRED_THROTTLE_UNLIMITED);
}
attitude_control->reset_rate_controller_I_terms();
attitude_control->set_yaw_target_to_current_heading();
attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(target_roll, target_pitch, target_yaw_rate, get_smoothing_gain());
pos_control->relax_alt_hold_controllers(0.0f);
pos_control->update_z_controller();
}else{
// check if pilot is overriding the controls
bool zero_rp_input = is_zero(target_roll) && is_zero(target_pitch);
if (!zero_rp_input || !is_zero(target_yaw_rate) || target_climb_rate != 0) {
if (!pilot_override) {
pilot_override = true;
// set gains to their original values
load_orig_gains();
attitude_control->use_ff_and_input_shaping(true);
}
// reset pilot override time
override_time = millis();
if (!zero_rp_input) {
// only reset position on roll or pitch input
have_position = false;
}
}else if (pilot_override) {
// check if we should resume tuning after pilot's override
if (millis() - override_time > AUTOTUNE_PILOT_OVERRIDE_TIMEOUT_MS) {
pilot_override = false; // turn off pilot override
// set gains to their intra-test values (which are very close to the original gains)
// load_intra_test_gains(); //I think we should be keeping the originals here to let the I term settle quickly
step = WAITING_FOR_LEVEL; // set tuning step back from beginning
desired_yaw = ahrs.yaw_sensor;
}
}
if (zero_rp_input) {
// pilot input on throttle and yaw will still use position hold if enabled
get_poshold_attitude(target_roll, target_pitch, desired_yaw);
}
// set motors to full range
motors->set_desired_spool_state(AP_Motors::DESIRED_THROTTLE_UNLIMITED);
// if pilot override call attitude controller
if (pilot_override || mode != TUNING) {
attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(target_roll, target_pitch, target_yaw_rate, get_smoothing_gain());
}else{
// somehow get attitude requests from autotuning
autotune_attitude_control();
}
// call position controller
pos_control->set_alt_target_from_climb_rate_ff(target_climb_rate, G_Dt, false);
pos_control->update_z_controller();
}
}
bool Copter::ModeAutoTune::check_level(const LEVEL_ISSUE issue, const float current, const float maximum)
{
if (current > maximum) {
level_problem.current = current;
level_problem.maximum = maximum;
level_problem.issue = issue;
return false;
}
return true;
}
bool Copter::ModeAutoTune::currently_level()
{
if (!check_level(LEVEL_ISSUE_ANGLE_ROLL,
labs(ahrs.roll_sensor - roll_cd),
AUTOTUNE_LEVEL_ANGLE_CD)) {
return false;
}
if (!check_level(LEVEL_ISSUE_ANGLE_PITCH,
labs(ahrs.pitch_sensor - pitch_cd),
AUTOTUNE_LEVEL_ANGLE_CD)) {
return false;
}
if (!check_level(LEVEL_ISSUE_ANGLE_YAW,
labs(wrap_180_cd(ahrs.yaw_sensor-(int32_t)desired_yaw)),
AUTOTUNE_LEVEL_ANGLE_CD)) {
return false;
}
if (!check_level(LEVEL_ISSUE_RATE_ROLL,
(ToDeg(ahrs.get_gyro().x) * 100.0f),
AUTOTUNE_LEVEL_RATE_RP_CD)) {
return false;
}
if (!check_level(LEVEL_ISSUE_RATE_PITCH,
(ToDeg(ahrs.get_gyro().y) * 100.0f),
AUTOTUNE_LEVEL_RATE_RP_CD)) {
return false;
}
if (!check_level(LEVEL_ISSUE_RATE_YAW,
(ToDeg(ahrs.get_gyro().z) * 100.0f),
AUTOTUNE_LEVEL_RATE_Y_CD)) {
return false;
}
return true;
}
// attitude_controller - sets attitude control targets during tuning
void Copter::ModeAutoTune::autotune_attitude_control()
{
rotation_rate = 0.0f; // rotation rate in radians/second
lean_angle = 0.0f;
const float direction_sign = positive_direction ? 1.0f : -1.0f;
// check tuning step
switch (step) {
case WAITING_FOR_LEVEL:
// Note: we should be using intra-test gains (which are very close to the original gains but have lower I)
// re-enable rate limits
attitude_control->use_ff_and_input_shaping(true);
get_poshold_attitude(roll_cd, pitch_cd, desired_yaw);
// hold level attitude
attitude_control->input_euler_angle_roll_pitch_yaw(roll_cd, pitch_cd, desired_yaw, true, get_smoothing_gain());
// hold the copter level for 0.5 seconds before we begin a twitch
// reset counter if we are no longer level
if (!currently_level()) {
step_start_time = millis();
}
// if we have been level for a sufficient amount of time (0.5 seconds) move onto tuning step
if (millis() - step_start_time >= AUTOTUNE_REQUIRED_LEVEL_TIME_MS) {
gcs().send_text(MAV_SEVERITY_INFO, "AutoTune: Twitch");
// initiate variables for next step
step = TWITCHING;
step_start_time = millis();
step_stop_time = step_start_time + AUTOTUNE_TESTING_STEP_TIMEOUT_MS;
twitch_first_iter = true;
test_max = 0.0f;
test_min = 0.0f;
rotation_rate_filt.reset(0.0f);
rate_max = 0.0f;
// set gains to their to-be-tested values
load_twitch_gains();
}
switch (axis) {
case ROLL:
target_rate = constrain_float(ToDeg(attitude_control->max_rate_step_bf_roll())*100.0f, AUTOTUNE_TARGET_MIN_RATE_RLLPIT_CDS, AUTOTUNE_TARGET_RATE_RLLPIT_CDS);
target_angle = constrain_float(ToDeg(attitude_control->max_angle_step_bf_roll())*100.0f, AUTOTUNE_TARGET_MIN_ANGLE_RLLPIT_CD, AUTOTUNE_TARGET_ANGLE_RLLPIT_CD);
start_rate = ToDeg(ahrs.get_gyro().x) * 100.0f;
start_angle = ahrs.roll_sensor;
rotation_rate_filt.set_cutoff_frequency(attitude_control->get_rate_roll_pid().filt_hz()*2.0f);
if ((tune_type == SP_DOWN) || (tune_type == SP_UP)) {
rotation_rate_filt.reset(start_rate);
} else {
rotation_rate_filt.reset(0);
}
break;
case PITCH:
target_rate = constrain_float(ToDeg(attitude_control->max_rate_step_bf_pitch())*100.0f, AUTOTUNE_TARGET_MIN_RATE_RLLPIT_CDS, AUTOTUNE_TARGET_RATE_RLLPIT_CDS);
target_angle = constrain_float(ToDeg(attitude_control->max_angle_step_bf_pitch())*100.0f, AUTOTUNE_TARGET_MIN_ANGLE_RLLPIT_CD, AUTOTUNE_TARGET_ANGLE_RLLPIT_CD);
start_rate = ToDeg(ahrs.get_gyro().y) * 100.0f;
start_angle = ahrs.pitch_sensor;
rotation_rate_filt.set_cutoff_frequency(attitude_control->get_rate_pitch_pid().filt_hz()*2.0f);
if ((tune_type == SP_DOWN) || (tune_type == SP_UP)) {
rotation_rate_filt.reset(start_rate);
} else {
rotation_rate_filt.reset(0);
}
break;
case YAW:
target_rate = constrain_float(ToDeg(attitude_control->max_rate_step_bf_yaw()*0.75f)*100.0f, AUTOTUNE_TARGET_MIN_RATE_YAW_CDS, AUTOTUNE_TARGET_RATE_YAW_CDS);
target_angle = constrain_float(ToDeg(attitude_control->max_angle_step_bf_yaw()*0.75f)*100.0f, AUTOTUNE_TARGET_MIN_ANGLE_YAW_CD, AUTOTUNE_TARGET_ANGLE_YAW_CD);
start_rate = ToDeg(ahrs.get_gyro().z) * 100.0f;
start_angle = ahrs.yaw_sensor;
rotation_rate_filt.set_cutoff_frequency(AUTOTUNE_Y_FILT_FREQ);
if ((tune_type == SP_DOWN) || (tune_type == SP_UP)) {
rotation_rate_filt.reset(start_rate);
} else {
rotation_rate_filt.reset(0);
}
break;
}
break;
case TWITCHING:
// Run the twitching step
// Note: we should be using intra-test gains (which are very close to the original gains but have lower I)
// disable rate limits
attitude_control->use_ff_and_input_shaping(false);
// hold current attitude
attitude_control->input_rate_bf_roll_pitch_yaw(0.0f, 0.0f, 0.0f);
if ((tune_type == SP_DOWN) || (tune_type == SP_UP)) {
// step angle targets on first iteration
if (twitch_first_iter) {
twitch_first_iter = false;
// Testing increasing stabilize P gain so will set lean angle target
switch (axis) {
case ROLL:
// request roll to 20deg
attitude_control->input_angle_step_bf_roll_pitch_yaw(direction_sign * target_angle, 0.0f, 0.0f);
break;
case PITCH:
// request pitch to 20deg
attitude_control->input_angle_step_bf_roll_pitch_yaw(0.0f, direction_sign * target_angle, 0.0f);
break;
case YAW:
// request pitch to 20deg
attitude_control->input_angle_step_bf_roll_pitch_yaw(0.0f, 0.0f, direction_sign * target_angle);
break;
}
}
} else {
// Testing rate P and D gains so will set body-frame rate targets.
// Rate controller will use existing body-frame rates and convert to motor outputs
// for all axes except the one we override here.
switch (axis) {
case ROLL:
// override body-frame roll rate
attitude_control->rate_bf_roll_target(direction_sign * target_rate + start_rate);
break;
case PITCH:
// override body-frame pitch rate
attitude_control->rate_bf_pitch_target(direction_sign * target_rate + start_rate);
break;
case YAW:
// override body-frame yaw rate
attitude_control->rate_bf_yaw_target(direction_sign * target_rate + start_rate);
break;
}
}
// capture this iterations rotation rate and lean angle
// Add filter to measurements
switch (axis) {
case ROLL:
if ((tune_type == SP_DOWN) || (tune_type == SP_UP)) {
rotation_rate = rotation_rate_filt.apply(direction_sign * (ToDeg(ahrs.get_gyro().x) * 100.0f), MAIN_LOOP_SECONDS);
} else {
rotation_rate = rotation_rate_filt.apply(direction_sign * (ToDeg(ahrs.get_gyro().x) * 100.0f - start_rate), MAIN_LOOP_SECONDS);
}
lean_angle = direction_sign * (ahrs.roll_sensor - (int32_t)start_angle);
break;
case PITCH:
if ((tune_type == SP_DOWN) || (tune_type == SP_UP)) {
rotation_rate = rotation_rate_filt.apply(direction_sign * (ToDeg(ahrs.get_gyro().y) * 100.0f), MAIN_LOOP_SECONDS);
} else {
rotation_rate = rotation_rate_filt.apply(direction_sign * (ToDeg(ahrs.get_gyro().y) * 100.0f - start_rate), MAIN_LOOP_SECONDS);
}
lean_angle = direction_sign * (ahrs.pitch_sensor - (int32_t)start_angle);
break;
case YAW:
if ((tune_type == SP_DOWN) || (tune_type == SP_UP)) {
rotation_rate = rotation_rate_filt.apply(direction_sign * (ToDeg(ahrs.get_gyro().z) * 100.0f), MAIN_LOOP_SECONDS);
} else {
rotation_rate = rotation_rate_filt.apply(direction_sign * (ToDeg(ahrs.get_gyro().z) * 100.0f - start_rate), MAIN_LOOP_SECONDS);
}
lean_angle = direction_sign * wrap_180_cd(ahrs.yaw_sensor-(int32_t)start_angle);
break;
}
switch (tune_type) {
case RD_UP:
case RD_DOWN:
twitching_test(rotation_rate, target_rate, test_min, test_max);
twitching_measure_acceleration(test_accel_max, rotation_rate, rate_max);
if (lean_angle >= target_angle) {
step = UPDATE_GAINS;
}
break;
case RP_UP:
twitching_test(rotation_rate, target_rate*(1+0.5f*g.autotune_aggressiveness), test_min, test_max);
twitching_measure_acceleration(test_accel_max, rotation_rate, rate_max);
if (lean_angle >= target_angle) {
step = UPDATE_GAINS;
}
break;
case SP_DOWN:
case SP_UP:
twitching_test(lean_angle, target_angle*(1+0.5f*g.autotune_aggressiveness), test_min, test_max);
twitching_measure_acceleration(test_accel_max, rotation_rate - direction_sign * start_rate, rate_max);
break;
}
// log this iterations lean angle and rotation rate
Log_Write_AutoTuneDetails(lean_angle, rotation_rate);
_copter.DataFlash.Log_Write_Rate(ahrs, *motors, *attitude_control, *pos_control);
break;
case UPDATE_GAINS:
// re-enable rate limits
attitude_control->use_ff_and_input_shaping(true);
// log the latest gains
if ((tune_type == SP_DOWN) || (tune_type == SP_UP)) {
switch (axis) {
case ROLL:
Log_Write_AutoTune(axis, tune_type, target_angle, test_min, test_max, tune_roll_rp, tune_roll_rd, tune_roll_sp, test_accel_max);
break;
case PITCH:
Log_Write_AutoTune(axis, tune_type, target_angle, test_min, test_max, tune_pitch_rp, tune_pitch_rd, tune_pitch_sp, test_accel_max);
break;
case YAW:
Log_Write_AutoTune(axis, tune_type, target_angle, test_min, test_max, tune_yaw_rp, tune_yaw_rLPF, tune_yaw_sp, test_accel_max);
break;
}
} else {
switch (axis) {
case ROLL:
Log_Write_AutoTune(axis, tune_type, target_rate, test_min, test_max, tune_roll_rp, tune_roll_rd, tune_roll_sp, test_accel_max);
break;
case PITCH:
Log_Write_AutoTune(axis, tune_type, target_rate, test_min, test_max, tune_pitch_rp, tune_pitch_rd, tune_pitch_sp, test_accel_max);
break;
case YAW:
Log_Write_AutoTune(axis, tune_type, target_rate, test_min, test_max, tune_yaw_rp, tune_yaw_rLPF, tune_yaw_sp, test_accel_max);
break;
}
}
// Check results after mini-step to increase rate D gain
switch (tune_type) {
case RD_UP:
switch (axis) {
case ROLL:
updating_d_up(tune_roll_rd, g.autotune_min_d, AUTOTUNE_RD_MAX, AUTOTUNE_RD_STEP, tune_roll_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
case PITCH:
updating_d_up(tune_pitch_rd, g.autotune_min_d, AUTOTUNE_RD_MAX, AUTOTUNE_RD_STEP, tune_pitch_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
case YAW:
updating_d_up(tune_yaw_rLPF, AUTOTUNE_RLPF_MIN, AUTOTUNE_RLPF_MAX, AUTOTUNE_RD_STEP, tune_yaw_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
}
break;
// Check results after mini-step to decrease rate D gain
case RD_DOWN:
switch (axis) {
case ROLL:
updating_d_down(tune_roll_rd, g.autotune_min_d, AUTOTUNE_RD_STEP, tune_roll_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
case PITCH:
updating_d_down(tune_pitch_rd, g.autotune_min_d, AUTOTUNE_RD_STEP, tune_pitch_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
case YAW:
updating_d_down(tune_yaw_rLPF, AUTOTUNE_RLPF_MIN, AUTOTUNE_RD_STEP, tune_yaw_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
}
break;
// Check results after mini-step to increase rate P gain
case RP_UP:
switch (axis) {
case ROLL:
updating_p_up_d_down(tune_roll_rd, g.autotune_min_d, AUTOTUNE_RD_STEP, tune_roll_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
case PITCH:
updating_p_up_d_down(tune_pitch_rd, g.autotune_min_d, AUTOTUNE_RD_STEP, tune_pitch_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
case YAW:
updating_p_up_d_down(tune_yaw_rLPF, AUTOTUNE_RLPF_MIN, AUTOTUNE_RD_STEP, tune_yaw_rp, AUTOTUNE_RP_MIN, AUTOTUNE_RP_MAX, AUTOTUNE_RP_STEP, target_rate, test_min, test_max);
break;
}
break;
// Check results after mini-step to increase stabilize P gain
case SP_DOWN:
switch (axis) {
case ROLL:
updating_p_down(tune_roll_sp, AUTOTUNE_SP_MIN, AUTOTUNE_SP_STEP, target_angle, test_max);
break;
case PITCH:
updating_p_down(tune_pitch_sp, AUTOTUNE_SP_MIN, AUTOTUNE_SP_STEP, target_angle, test_max);
break;
case YAW:
updating_p_down(tune_yaw_sp, AUTOTUNE_SP_MIN, AUTOTUNE_SP_STEP, target_angle, test_max);
break;
}
break;
// Check results after mini-step to increase stabilize P gain
case SP_UP:
switch (axis) {
case ROLL:
updating_p_up(tune_roll_sp, AUTOTUNE_SP_MAX, AUTOTUNE_SP_STEP, target_angle, test_max);
break;
case PITCH:
updating_p_up(tune_pitch_sp, AUTOTUNE_SP_MAX, AUTOTUNE_SP_STEP, target_angle, test_max);
break;
case YAW:
updating_p_up(tune_yaw_sp, AUTOTUNE_SP_MAX, AUTOTUNE_SP_STEP, target_angle, test_max);
break;
}
break;
}
// we've complete this step, finalize pids and move to next step
if (counter >= AUTOTUNE_SUCCESS_COUNT) {
// reset counter
counter = 0;
// move to the next tuning type
switch (tune_type) {
case RD_UP:
tune_type = TuneType(tune_type + 1);
break;
case RD_DOWN:
tune_type = TuneType(tune_type + 1);
switch (axis) {
case ROLL:
tune_roll_rd = MAX(g.autotune_min_d, tune_roll_rd * AUTOTUNE_RD_BACKOFF);
tune_roll_rp = MAX(AUTOTUNE_RP_MIN, tune_roll_rp * AUTOTUNE_RD_BACKOFF);
break;
case PITCH:
tune_pitch_rd = MAX(g.autotune_min_d, tune_pitch_rd * AUTOTUNE_RD_BACKOFF);
tune_pitch_rp = MAX(AUTOTUNE_RP_MIN, tune_pitch_rp * AUTOTUNE_RD_BACKOFF);
break;
case YAW:
tune_yaw_rLPF = MAX(AUTOTUNE_RLPF_MIN, tune_yaw_rLPF * AUTOTUNE_RD_BACKOFF);
tune_yaw_rp = MAX(AUTOTUNE_RP_MIN, tune_yaw_rp * AUTOTUNE_RD_BACKOFF);
break;
}
break;
case RP_UP:
tune_type = TuneType(tune_type + 1);
switch (axis) {
case ROLL:
tune_roll_rp = MAX(AUTOTUNE_RP_MIN, tune_roll_rp * AUTOTUNE_RP_BACKOFF);
break;
case PITCH:
tune_pitch_rp = MAX(AUTOTUNE_RP_MIN, tune_pitch_rp * AUTOTUNE_RP_BACKOFF);
break;
case YAW:
tune_yaw_rp = MAX(AUTOTUNE_RP_MIN, tune_yaw_rp * AUTOTUNE_RP_BACKOFF);
break;
}
break;
case SP_DOWN:
tune_type = TuneType(tune_type + 1);
break;
case SP_UP:
// we've reached the end of a D-up-down PI-up-down tune type cycle
tune_type = RD_UP;
// advance to the next axis
bool complete = false;
switch (axis) {
case ROLL:
tune_roll_sp = MAX(AUTOTUNE_SP_MIN, tune_roll_sp * AUTOTUNE_SP_BACKOFF);
tune_roll_accel = MAX(AUTOTUNE_RP_ACCEL_MIN, test_accel_max * AUTOTUNE_ACCEL_RP_BACKOFF);
if (pitch_enabled()) {
axis = PITCH;
} else if (yaw_enabled()) {
axis = YAW;
} else {
complete = true;
}
break;
case PITCH:
tune_pitch_sp = MAX(AUTOTUNE_SP_MIN, tune_pitch_sp * AUTOTUNE_SP_BACKOFF);
tune_pitch_accel = MAX(AUTOTUNE_RP_ACCEL_MIN, test_accel_max * AUTOTUNE_ACCEL_RP_BACKOFF);
if (yaw_enabled()) {
axis = YAW;
} else {
complete = true;
}
break;
case YAW:
tune_yaw_sp = MAX(AUTOTUNE_SP_MIN, tune_yaw_sp * AUTOTUNE_SP_BACKOFF);
tune_yaw_accel = MAX(AUTOTUNE_Y_ACCEL_MIN, test_accel_max * AUTOTUNE_ACCEL_Y_BACKOFF);
complete = true;
break;
}
// if we've just completed all axes we have successfully completed the autotune
// change to TESTING mode to allow user to fly with new gains
if (complete) {
mode = SUCCESS;
update_gcs(AUTOTUNE_MESSAGE_SUCCESS);
Log_Write_Event(DATA_AUTOTUNE_SUCCESS);
AP_Notify::events.autotune_complete = 1;
} else {
AP_Notify::events.autotune_next_axis = 1;
}
break;
}
}
// reverse direction
positive_direction = !positive_direction;
if (axis == YAW) {
attitude_control->input_euler_angle_roll_pitch_yaw(0.0f, 0.0f, ahrs.yaw_sensor, false, get_smoothing_gain());
}
// set gains to their intra-test values (which are very close to the original gains)
load_intra_test_gains();
// reset testing step
step = WAITING_FOR_LEVEL;
step_start_time = millis();
break;
}
}
// backup_gains_and_initialise - store current gains as originals
// called before tuning starts to backup original gains
void Copter::ModeAutoTune::backup_gains_and_initialise()
{
// initialise state because this is our first time
if (roll_enabled()) {
axis = ROLL;
} else if (pitch_enabled()) {
axis = PITCH;
} else if (yaw_enabled()) {
axis = YAW;
}
positive_direction = false;
step = WAITING_FOR_LEVEL;
step_start_time = millis();
tune_type = RD_UP;
desired_yaw = ahrs.yaw_sensor;
g.autotune_aggressiveness = constrain_float(g.autotune_aggressiveness, 0.05f, 0.2f);
orig_bf_feedforward = attitude_control->get_bf_feedforward();
// backup original pids and initialise tuned pid values
orig_roll_rp = attitude_control->get_rate_roll_pid().kP();
orig_roll_ri = attitude_control->get_rate_roll_pid().kI();
orig_roll_rd = attitude_control->get_rate_roll_pid().kD();
orig_roll_sp = attitude_control->get_angle_roll_p().kP();
orig_roll_accel = attitude_control->get_accel_roll_max();
tune_roll_rp = attitude_control->get_rate_roll_pid().kP();
tune_roll_rd = attitude_control->get_rate_roll_pid().kD();
tune_roll_sp = attitude_control->get_angle_roll_p().kP();
tune_roll_accel = attitude_control->get_accel_roll_max();
orig_pitch_rp = attitude_control->get_rate_pitch_pid().kP();
orig_pitch_ri = attitude_control->get_rate_pitch_pid().kI();
orig_pitch_rd = attitude_control->get_rate_pitch_pid().kD();
orig_pitch_sp = attitude_control->get_angle_pitch_p().kP();
orig_pitch_accel = attitude_control->get_accel_pitch_max();
tune_pitch_rp = attitude_control->get_rate_pitch_pid().kP();
tune_pitch_rd = attitude_control->get_rate_pitch_pid().kD();
tune_pitch_sp = attitude_control->get_angle_pitch_p().kP();
tune_pitch_accel = attitude_control->get_accel_pitch_max();
orig_yaw_rp = attitude_control->get_rate_yaw_pid().kP();
orig_yaw_ri = attitude_control->get_rate_yaw_pid().kI();
orig_yaw_rd = attitude_control->get_rate_yaw_pid().kD();
orig_yaw_rLPF = attitude_control->get_rate_yaw_pid().filt_hz();
orig_yaw_accel = attitude_control->get_accel_yaw_max();
orig_yaw_sp = attitude_control->get_angle_yaw_p().kP();
tune_yaw_rp = attitude_control->get_rate_yaw_pid().kP();
tune_yaw_rLPF = attitude_control->get_rate_yaw_pid().filt_hz();
tune_yaw_sp = attitude_control->get_angle_yaw_p().kP();
tune_yaw_accel = attitude_control->get_accel_yaw_max();
Log_Write_Event(DATA_AUTOTUNE_INITIALISED);
}
// load_orig_gains - set gains to their original values
// called by stop and failed functions
void Copter::ModeAutoTune::load_orig_gains()
{
attitude_control->bf_feedforward(orig_bf_feedforward);
if (roll_enabled()) {
if (!is_zero(orig_roll_rp)) {
attitude_control->get_rate_roll_pid().kP(orig_roll_rp);
attitude_control->get_rate_roll_pid().kI(orig_roll_ri);
attitude_control->get_rate_roll_pid().kD(orig_roll_rd);
attitude_control->get_angle_roll_p().kP(orig_roll_sp);
attitude_control->set_accel_roll_max(orig_roll_accel);
}
}
if (pitch_enabled()) {
if (!is_zero(orig_pitch_rp)) {
attitude_control->get_rate_pitch_pid().kP(orig_pitch_rp);
attitude_control->get_rate_pitch_pid().kI(orig_pitch_ri);
attitude_control->get_rate_pitch_pid().kD(orig_pitch_rd);
attitude_control->get_angle_pitch_p().kP(orig_pitch_sp);
attitude_control->set_accel_pitch_max(orig_pitch_accel);
}
}
if (yaw_enabled()) {
if (!is_zero(orig_yaw_rp)) {
attitude_control->get_rate_yaw_pid().kP(orig_yaw_rp);
attitude_control->get_rate_yaw_pid().kI(orig_yaw_ri);
attitude_control->get_rate_yaw_pid().kD(orig_yaw_rd);
attitude_control->get_rate_yaw_pid().filt_hz(orig_yaw_rLPF);
attitude_control->get_angle_yaw_p().kP(orig_yaw_sp);
attitude_control->set_accel_yaw_max(orig_yaw_accel);
}
}
}
// load_tuned_gains - load tuned gains
void Copter::ModeAutoTune::load_tuned_gains()
{
if (!attitude_control->get_bf_feedforward()) {
attitude_control->bf_feedforward(true);
attitude_control->set_accel_roll_max(0.0f);
attitude_control->set_accel_pitch_max(0.0f);
}
if (roll_enabled()) {
if (!is_zero(tune_roll_rp)) {
attitude_control->get_rate_roll_pid().kP(tune_roll_rp);
attitude_control->get_rate_roll_pid().kI(tune_roll_rp*AUTOTUNE_PI_RATIO_FINAL);
attitude_control->get_rate_roll_pid().kD(tune_roll_rd);
attitude_control->get_angle_roll_p().kP(tune_roll_sp);
attitude_control->set_accel_roll_max(tune_roll_accel);
}
}
if (pitch_enabled()) {
if (!is_zero(tune_pitch_rp)) {
attitude_control->get_rate_pitch_pid().kP(tune_pitch_rp);
attitude_control->get_rate_pitch_pid().kI(tune_pitch_rp*AUTOTUNE_PI_RATIO_FINAL);
attitude_control->get_rate_pitch_pid().kD(tune_pitch_rd);
attitude_control->get_angle_pitch_p().kP(tune_pitch_sp);
attitude_control->set_accel_pitch_max(tune_pitch_accel);
}
}
if (yaw_enabled()) {
if (!is_zero(tune_yaw_rp)) {
attitude_control->get_rate_yaw_pid().kP(tune_yaw_rp);
attitude_control->get_rate_yaw_pid().kI(tune_yaw_rp*AUTOTUNE_YAW_PI_RATIO_FINAL);
attitude_control->get_rate_yaw_pid().kD(0.0f);
attitude_control->get_rate_yaw_pid().filt_hz(tune_yaw_rLPF);
attitude_control->get_angle_yaw_p().kP(tune_yaw_sp);
attitude_control->set_accel_yaw_max(tune_yaw_accel);
}
}
}
// load_intra_test_gains - gains used between tests
// called during testing mode's update-gains step to set gains ahead of return-to-level step
void Copter::ModeAutoTune::load_intra_test_gains()
{
// we are restarting tuning so reset gains to tuning-start gains (i.e. low I term)
// sanity check the gains
attitude_control->bf_feedforward(true);
if (roll_enabled()) {
attitude_control->get_rate_roll_pid().kP(orig_roll_rp);
attitude_control->get_rate_roll_pid().kI(orig_roll_rp*AUTOTUNE_PI_RATIO_FOR_TESTING);
attitude_control->get_rate_roll_pid().kD(orig_roll_rd);
attitude_control->get_angle_roll_p().kP(orig_roll_sp);
}
if (pitch_enabled()) {
attitude_control->get_rate_pitch_pid().kP(orig_pitch_rp);
attitude_control->get_rate_pitch_pid().kI(orig_pitch_rp*AUTOTUNE_PI_RATIO_FOR_TESTING);
attitude_control->get_rate_pitch_pid().kD(orig_pitch_rd);
attitude_control->get_angle_pitch_p().kP(orig_pitch_sp);
}
if (yaw_enabled()) {
attitude_control->get_rate_yaw_pid().kP(orig_yaw_rp);
attitude_control->get_rate_yaw_pid().kI(orig_yaw_rp*AUTOTUNE_PI_RATIO_FOR_TESTING);
attitude_control->get_rate_yaw_pid().kD(orig_yaw_rd);
attitude_control->get_rate_yaw_pid().filt_hz(orig_yaw_rLPF);
attitude_control->get_angle_yaw_p().kP(orig_yaw_sp);
}
}
// load_twitch_gains - load the to-be-tested gains for a single axis
// called by attitude_control() just before it beings testing a gain (i.e. just before it twitches)
void Copter::ModeAutoTune::load_twitch_gains()
{
switch (axis) {
case ROLL:
attitude_control->get_rate_roll_pid().kP(tune_roll_rp);
attitude_control->get_rate_roll_pid().kI(tune_roll_rp*0.01f);
attitude_control->get_rate_roll_pid().kD(tune_roll_rd);
attitude_control->get_angle_roll_p().kP(tune_roll_sp);
break;
case PITCH:
attitude_control->get_rate_pitch_pid().kP(tune_pitch_rp);
attitude_control->get_rate_pitch_pid().kI(tune_pitch_rp*0.01f);
attitude_control->get_rate_pitch_pid().kD(tune_pitch_rd);
attitude_control->get_angle_pitch_p().kP(tune_pitch_sp);
break;
case YAW:
attitude_control->get_rate_yaw_pid().kP(tune_yaw_rp);
attitude_control->get_rate_yaw_pid().kI(tune_yaw_rp*0.01f);
attitude_control->get_rate_yaw_pid().kD(0.0f);
attitude_control->get_rate_yaw_pid().filt_hz(tune_yaw_rLPF);
attitude_control->get_angle_yaw_p().kP(tune_yaw_sp);
break;
}
}
// save_tuning_gains - save the final tuned gains for each axis
// save discovered gains to eeprom if autotuner is enabled (i.e. switch is in the high position)
void Copter::ModeAutoTune::save_tuning_gains()
{
// if we successfully completed tuning
if (mode == SUCCESS) {
if (!attitude_control->get_bf_feedforward()) {
attitude_control->bf_feedforward_save(true);
attitude_control->save_accel_roll_max(0.0f);
attitude_control->save_accel_pitch_max(0.0f);
}
// sanity check the rate P values
if (roll_enabled() && !is_zero(tune_roll_rp)) {
// rate roll gains
attitude_control->get_rate_roll_pid().kP(tune_roll_rp);
attitude_control->get_rate_roll_pid().kI(tune_roll_rp*AUTOTUNE_PI_RATIO_FINAL);
attitude_control->get_rate_roll_pid().kD(tune_roll_rd);
attitude_control->get_rate_roll_pid().save_gains();
// stabilize roll
attitude_control->get_angle_roll_p().kP(tune_roll_sp);
attitude_control->get_angle_roll_p().save_gains();
// acceleration roll
attitude_control->save_accel_roll_max(tune_roll_accel);
// resave pids to originals in case the autotune is run again
orig_roll_rp = attitude_control->get_rate_roll_pid().kP();
orig_roll_ri = attitude_control->get_rate_roll_pid().kI();
orig_roll_rd = attitude_control->get_rate_roll_pid().kD();
orig_roll_sp = attitude_control->get_angle_roll_p().kP();
orig_roll_accel = attitude_control->get_accel_roll_max();
}
if (pitch_enabled() && !is_zero(tune_pitch_rp)) {
// rate pitch gains
attitude_control->get_rate_pitch_pid().kP(tune_pitch_rp);
attitude_control->get_rate_pitch_pid().kI(tune_pitch_rp*AUTOTUNE_PI_RATIO_FINAL);
attitude_control->get_rate_pitch_pid().kD(tune_pitch_rd);
attitude_control->get_rate_pitch_pid().save_gains();
// stabilize pitch
attitude_control->get_angle_pitch_p().kP(tune_pitch_sp);
attitude_control->get_angle_pitch_p().save_gains();
// acceleration pitch
attitude_control->save_accel_pitch_max(tune_pitch_accel);
// resave pids to originals in case the autotune is run again
orig_pitch_rp = attitude_control->get_rate_pitch_pid().kP();
orig_pitch_ri = attitude_control->get_rate_pitch_pid().kI();
orig_pitch_rd = attitude_control->get_rate_pitch_pid().kD();
orig_pitch_sp = attitude_control->get_angle_pitch_p().kP();
orig_pitch_accel = attitude_control->get_accel_pitch_max();
}
if (yaw_enabled() && !is_zero(tune_yaw_rp)) {
// rate yaw gains
attitude_control->get_rate_yaw_pid().kP(tune_yaw_rp);
attitude_control->get_rate_yaw_pid().kI(tune_yaw_rp*AUTOTUNE_YAW_PI_RATIO_FINAL);
attitude_control->get_rate_yaw_pid().kD(0.0f);
attitude_control->get_rate_yaw_pid().filt_hz(tune_yaw_rLPF);
attitude_control->get_rate_yaw_pid().save_gains();
// stabilize yaw
attitude_control->get_angle_yaw_p().kP(tune_yaw_sp);
attitude_control->get_angle_yaw_p().save_gains();
// acceleration yaw
attitude_control->save_accel_yaw_max(tune_yaw_accel);
// resave pids to originals in case the autotune is run again
orig_yaw_rp = attitude_control->get_rate_yaw_pid().kP();
orig_yaw_ri = attitude_control->get_rate_yaw_pid().kI();
orig_yaw_rd = attitude_control->get_rate_yaw_pid().kD();
orig_yaw_rLPF = attitude_control->get_rate_yaw_pid().filt_hz();
orig_yaw_sp = attitude_control->get_angle_yaw_p().kP();
orig_yaw_accel = attitude_control->get_accel_pitch_max();
}
// update GCS and log save gains event
update_gcs(AUTOTUNE_MESSAGE_SAVED_GAINS);
Log_Write_Event(DATA_AUTOTUNE_SAVEDGAINS);
// reset Autotune so that gains are not saved again and autotune can be run again.
mode = UNINITIALISED;
}
}
// update_gcs - send message to ground station
void Copter::ModeAutoTune::update_gcs(uint8_t message_id)
{
switch (message_id) {
case AUTOTUNE_MESSAGE_STARTED:
gcs().send_text(MAV_SEVERITY_INFO,"AutoTune: Started");
break;
case AUTOTUNE_MESSAGE_STOPPED:
gcs().send_text(MAV_SEVERITY_INFO,"AutoTune: Stopped");
break;
case AUTOTUNE_MESSAGE_SUCCESS:
gcs().send_text(MAV_SEVERITY_INFO,"AutoTune: Success");
break;
case AUTOTUNE_MESSAGE_FAILED:
gcs().send_text(MAV_SEVERITY_NOTICE,"AutoTune: Failed");
break;
case AUTOTUNE_MESSAGE_SAVED_GAINS:
gcs().send_text(MAV_SEVERITY_INFO,"AutoTune: Saved gains");
break;
}
}
// axis helper functions
inline bool Copter::ModeAutoTune::roll_enabled() {
return g.autotune_axis_bitmask & AUTOTUNE_AXIS_BITMASK_ROLL;
}
inline bool Copter::ModeAutoTune::pitch_enabled() {
return g.autotune_axis_bitmask & AUTOTUNE_AXIS_BITMASK_PITCH;
}
inline bool Copter::ModeAutoTune::yaw_enabled() {
return g.autotune_axis_bitmask & AUTOTUNE_AXIS_BITMASK_YAW;
}
// twitching_test - twitching tests
// update min and max and test for end conditions
void Copter::ModeAutoTune::twitching_test(float measurement, float target, float &measurement_min, float &measurement_max)
{
// capture maximum measurement
if (measurement > measurement_max) {
// the measurement is continuing to increase without stopping
measurement_max = measurement;
measurement_min = measurement;
}
// capture minimum measurement after the measurement has peaked (aka "bounce back")
if ((measurement < measurement_min) && (measurement_max > target * 0.5f)) {
// the measurement is bouncing back
measurement_min = measurement;
}
// calculate early stopping time based on the time it takes to get to 90%
if (measurement_max < target * 0.75f) {
// the measurement not reached the 90% threshold yet
step_stop_time = step_start_time + (millis() - step_start_time) * 3.0f;
step_stop_time = MIN(step_stop_time, step_start_time + AUTOTUNE_TESTING_STEP_TIMEOUT_MS);
}
if (measurement_max > target) {
// the measurement has passed the target
step = UPDATE_GAINS;
}
if (measurement_max-measurement_min > measurement_max*g.autotune_aggressiveness) {
// the measurement has passed 50% of the target and bounce back is larger than the threshold
step = UPDATE_GAINS;
}
if (millis() >= step_stop_time) {
// we have passed the maximum stop time
step = UPDATE_GAINS;
}
}
// updating_d_up - increase D and adjust P to optimize the D term for a little bounce back
// optimize D term while keeping the maximum just below the target by adjusting P
void Copter::ModeAutoTune::updating_d_up(float &tune_d, float tune_d_min, float tune_d_max, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max)
{
if (measurement_max > target) {
// if maximum measurement was higher than target
// reduce P gain (which should reduce maximum)
tune_p -= tune_p*tune_p_step_ratio;
if (tune_p < tune_p_min) {
// P gain is at minimum so start reducing D
tune_p = tune_p_min;
tune_d -= tune_d*tune_d_step_ratio;
if (tune_d <= tune_d_min) {
// We have reached minimum D gain so stop tuning
tune_d = tune_d_min;
counter = AUTOTUNE_SUCCESS_COUNT;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
}
}else if ((measurement_max < target*(1.0f-AUTOTUNE_D_UP_DOWN_MARGIN)) && (tune_p <= tune_p_max)) {
// we have not achieved a high enough maximum to get a good measurement of bounce back.
// increase P gain (which should increase maximum)
tune_p += tune_p*tune_p_step_ratio;
if (tune_p >= tune_p_max) {
tune_p = tune_p_max;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
}else{
// we have a good measurement of bounce back
if (measurement_max-measurement_min > measurement_max*g.autotune_aggressiveness) {
// ignore the next result unless it is the same as this one
ignore_next = true;
// bounce back is bigger than our threshold so increment the success counter
counter++;
}else{
if (ignore_next == false) {
// bounce back is smaller than our threshold so decrement the success counter
if (counter > 0 ) {
counter--;
}
// increase D gain (which should increase bounce back)
tune_d += tune_d*tune_d_step_ratio*2.0f;
// stop tuning if we hit maximum D
if (tune_d >= tune_d_max) {
tune_d = tune_d_max;
counter = AUTOTUNE_SUCCESS_COUNT;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
} else {
ignore_next = false;
}
}
}
}
// updating_d_down - decrease D and adjust P to optimize the D term for no bounce back
// optimize D term while keeping the maximum just below the target by adjusting P
void Copter::ModeAutoTune::updating_d_down(float &tune_d, float tune_d_min, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max)
{
if (measurement_max > target) {
// if maximum measurement was higher than target
// reduce P gain (which should reduce maximum)
tune_p -= tune_p*tune_p_step_ratio;
if (tune_p < tune_p_min) {
// P gain is at minimum so start reducing D gain
tune_p = tune_p_min;
tune_d -= tune_d*tune_d_step_ratio;
if (tune_d <= tune_d_min) {
// We have reached minimum D so stop tuning
tune_d = tune_d_min;
counter = AUTOTUNE_SUCCESS_COUNT;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
}
}else if ((measurement_max < target*(1.0f-AUTOTUNE_D_UP_DOWN_MARGIN)) && (tune_p <= tune_p_max)) {
// we have not achieved a high enough maximum to get a good measurement of bounce back.
// increase P gain (which should increase maximum)
tune_p += tune_p*tune_p_step_ratio;
if (tune_p >= tune_p_max) {
tune_p = tune_p_max;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
}else{
// we have a good measurement of bounce back
if (measurement_max-measurement_min < measurement_max*g.autotune_aggressiveness) {
if (ignore_next == false) {
// bounce back is less than our threshold so increment the success counter
counter++;
} else {
ignore_next = false;
}
}else{
// ignore the next result unless it is the same as this one
ignore_next = true;
// bounce back is larger than our threshold so decrement the success counter
if (counter > 0 ) {
counter--;
}
// decrease D gain (which should decrease bounce back)
tune_d -= tune_d*tune_d_step_ratio;
// stop tuning if we hit minimum D
if (tune_d <= tune_d_min) {
tune_d = tune_d_min;
counter = AUTOTUNE_SUCCESS_COUNT;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
}
}
}
// updating_p_down - decrease P until we don't reach the target before time out
// P is decreased to ensure we are not overshooting the target
void Copter::ModeAutoTune::updating_p_down(float &tune_p, float tune_p_min, float tune_p_step_ratio, float target, float measurement_max)
{
if (measurement_max < target*(1+0.5f*g.autotune_aggressiveness)) {
if (ignore_next == false) {
// if maximum measurement was lower than target so increment the success counter
counter++;
} else {
ignore_next = false;
}
}else{
// ignore the next result unless it is the same as this one
ignore_next = true;
// if maximum measurement was higher than target so decrement the success counter
if (counter > 0 ) {
counter--;
}
// decrease P gain (which should decrease the maximum)
tune_p -= tune_p*tune_p_step_ratio;
// stop tuning if we hit maximum P
if (tune_p <= tune_p_min) {
tune_p = tune_p_min;
counter = AUTOTUNE_SUCCESS_COUNT;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
}
}
// updating_p_up - increase P to ensure the target is reached
// P is increased until we achieve our target within a reasonable time
void Copter::ModeAutoTune::updating_p_up(float &tune_p, float tune_p_max, float tune_p_step_ratio, float target, float measurement_max)
{
if (measurement_max > target*(1+0.5f*g.autotune_aggressiveness)) {
// ignore the next result unless it is the same as this one
ignore_next = 1;
// if maximum measurement was greater than target so increment the success counter
counter++;
}else{
if (ignore_next == false) {
// if maximum measurement was lower than target so decrement the success counter
if (counter > 0 ) {
counter--;
}
// increase P gain (which should increase the maximum)
tune_p += tune_p*tune_p_step_ratio;
// stop tuning if we hit maximum P
if (tune_p >= tune_p_max) {
tune_p = tune_p_max;
counter = AUTOTUNE_SUCCESS_COUNT;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
} else {
ignore_next = false;
}
}
}
// updating_p_up - increase P to ensure the target is reached while checking bounce back isn't increasing
// P is increased until we achieve our target within a reasonable time while reducing D if bounce back increases above the threshold
void Copter::ModeAutoTune::updating_p_up_d_down(float &tune_d, float tune_d_min, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max)
{
if (measurement_max > target*(1+0.5f*g.autotune_aggressiveness)) {
// ignore the next result unless it is the same as this one
ignore_next = true;
// if maximum measurement was greater than target so increment the success counter
counter++;
} else if ((measurement_max < target) && (measurement_max > target*(1.0f-AUTOTUNE_D_UP_DOWN_MARGIN)) && (measurement_max-measurement_min > measurement_max*g.autotune_aggressiveness) && (tune_d > tune_d_min)) {
// if bounce back was larger than the threshold so decrement the success counter
if (counter > 0 ) {
counter--;
}
// decrease D gain (which should decrease bounce back)
tune_d -= tune_d*tune_d_step_ratio;
// stop tuning if we hit minimum D
if (tune_d <= tune_d_min) {
tune_d = tune_d_min;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
// decrease P gain to match D gain reduction
tune_p -= tune_p*tune_p_step_ratio;
// stop tuning if we hit minimum P
if (tune_p <= tune_p_min) {
tune_p = tune_p_min;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
// cancel change in direction
positive_direction = !positive_direction;
}else{
if (ignore_next == false) {
// if maximum measurement was lower than target so decrement the success counter
if (counter > 0 ) {
counter--;
}
// increase P gain (which should increase the maximum)
tune_p += tune_p*tune_p_step_ratio;
// stop tuning if we hit maximum P
if (tune_p >= tune_p_max) {
tune_p = tune_p_max;
counter = AUTOTUNE_SUCCESS_COUNT;
Log_Write_Event(DATA_AUTOTUNE_REACHED_LIMIT);
}
} else {
ignore_next = false;
}
}
}
// twitching_measure_acceleration - measure rate of change of measurement
void Copter::ModeAutoTune::twitching_measure_acceleration(float &rate_of_change, float rate_measurement, float &rate_measurement_max)
{
if (rate_measurement_max < rate_measurement) {
rate_measurement_max = rate_measurement;
rate_of_change = (1000.0f*rate_measurement_max)/(millis() - step_start_time);
}
}
// get attitude for slow position hold in autotune mode
void Copter::ModeAutoTune::get_poshold_attitude(float &roll_cd_out, float &pitch_cd_out, float &yaw_cd_out)
{
roll_cd_out = pitch_cd_out = 0;
if (!use_poshold) {
// we are not trying to hold position
return;
}
// do we know where we are?
if (!_copter.position_ok()) {
return;
}
if (!have_position) {
have_position = true;
start_position = inertial_nav.get_position();
}
// don't go past 10 degrees, as autotune result would deteriorate too much
const float angle_max_cd = 1000;
// hit the 10 degree limit at 20 meters position error
const float dist_limit_cm = 2000;
// we only start adjusting yaw if we are more than 5m from the
// target position. That corresponds to a lean angle of 2.5 degrees
const float yaw_dist_limit_cm = 500;
Vector3f pdiff = inertial_nav.get_position() - start_position;
pdiff.z = 0;
float dist_cm = pdiff.length();
if (dist_cm < 10) {
// don't do anything within 10cm
return;
}
/*
very simple linear controller
*/
float scaling = constrain_float(angle_max_cd * dist_cm / dist_limit_cm, 0, angle_max_cd);
Vector2f angle_ne(pdiff.x, pdiff.y);
angle_ne *= scaling / dist_cm;
// rotate into body frame
pitch_cd_out = angle_ne.x * ahrs.cos_yaw() + angle_ne.y * ahrs.sin_yaw();
roll_cd_out = angle_ne.x * ahrs.sin_yaw() - angle_ne.y * ahrs.cos_yaw();
if (dist_cm < yaw_dist_limit_cm) {
// no yaw adjustment
return;
}
/*
also point so that twitching occurs perpendicular to the wind,
if we have drifted more than yaw_dist_limit_cm from the desired
position. This ensures that autotune doesn't have to deal with
more than 2.5 degrees of attitude on the axis it is tuning
*/
float target_yaw_cd = degrees(atan2f(pdiff.y, pdiff.x)) * 100;
if (axis == PITCH) {
// for roll and yaw tuning we point along the wind, for pitch
// we point across the wind
target_yaw_cd += 9000;
}
// go to the nearest 180 degree mark, with 5 degree slop to prevent oscillation
if (fabsf(yaw_cd_out - target_yaw_cd) > 9500) {
target_yaw_cd += 18000;
}
yaw_cd_out = target_yaw_cd;
}
#endif // AUTOTUNE_ENABLED == ENABLED
Reference in New Issue View Git Blame Copy Permalink