mirror of https://github.com/ArduPilot/ardupilot
82 lines
1.6 KiB
Plaintext
82 lines
1.6 KiB
Plaintext
#NOTE: AION Robotics Params for Rover V3.2.0
|
|
ACRO_TURN_RATE,120
|
|
#most users will want manual capabilites on boot without the need for a GCS to arm
|
|
ARMING_REQUIRE,0
|
|
#MIN 4S SOLO BATTERY
|
|
ARMING_VOLT_MIN,13
|
|
#default aux ch to match documentation
|
|
ATC_SPEED_P,0.2
|
|
ATC_SPEED_I,0.2
|
|
ATC_SPEED_D,0.0
|
|
ATC_SPEED_FILT,10
|
|
ATC_STR_RAT_FF,0.2
|
|
ATC_STR_RAT_P,0.0
|
|
ATC_STR_RAT_I,0.1
|
|
ATC_STR_RAT_D,0.0
|
|
ATC_STR_RAT_FILT,20
|
|
AUX_CH,7
|
|
#cube power brick - 4s solo battery - SMBus hardware side not yet supported
|
|
BATT_AMP_OFFSET,0
|
|
BATT_AMP_PERVOLT,0.1
|
|
BATT_CAPACITY,5200
|
|
BATT_CURR_PIN,3
|
|
BATT_LOW_TIMER,10
|
|
BATT_LOW_TYPE,0
|
|
BATT_MONITOR,4
|
|
BATT_SERIAL_NUM,-1
|
|
BATT_VOLT_MULT,13.99818
|
|
BATT_VOLT_PIN,2
|
|
BRD_PWM_COUNT,2
|
|
#default save waypoint
|
|
CH7_OPTION,1
|
|
COMPASS_OFFS_MAX,2000
|
|
#default use only first (hopefully external) compass
|
|
COMPASS_USE,1
|
|
COMPASS_USE2,0
|
|
COMPASS_USE3,0
|
|
CRUISE_SPEED,1.0
|
|
CRUISE_THROTTLE,70
|
|
EK2_YAW_M_NSE,0.7
|
|
FS_CRASH_CHECK,1
|
|
#default modes
|
|
MODE_CH,5
|
|
MODE1,0
|
|
MODE2,3
|
|
MODE3,10
|
|
MODE4,12
|
|
NAVL1_PERIOD,6
|
|
NAVL1_DAMPING,0.7
|
|
NAVL1_XTRACK_I,0.02
|
|
PIVOT_TURN_ANGLE,30
|
|
#default telem radio
|
|
SERIAL1_BAUD,57
|
|
SERIAL1_PROTOCOL,1
|
|
#default APSync
|
|
SERIAL2_BAUD,921
|
|
SERIAL2_PROTOCOL,1
|
|
SERVO1_FUNCTION,74
|
|
SERVO1_MAX,2000
|
|
SERVO1_MIN,1000
|
|
SERVO3_FUNCTION,73
|
|
SERVO3_MAX,2000
|
|
SERVO3_MIN,1000
|
|
SPEED_TURN_GAIN,50
|
|
TURN_MAX_G,0.3
|
|
TURN_RADIUS,0.9
|
|
WENC_CPR,1120
|
|
WENC_PINA,55
|
|
WENC_PINB,54
|
|
WENC_POS_X,-0.15
|
|
WENC_POS_Y,-0.16
|
|
WENC_POS_Z,0
|
|
WENC_RADIUS,0.0775
|
|
WENC_TYPE,0
|
|
WENC2_CPR,1120
|
|
WENC2_PINA,53
|
|
WENC2_PINB,52
|
|
WENC2_POS_X,-0.15
|
|
WENC2_POS_Y,0.16
|
|
WENC2_POS_Z,0
|
|
WENC_RADIUS,0.0775
|
|
WENC2_TYPE,0
|