mirror of https://github.com/ArduPilot/ardupilot
132 lines
3.5 KiB
Plaintext
132 lines
3.5 KiB
Plaintext
# hardware setup for V2450, based around FMUv3 but no IO MCU and
|
|
# custom config options for ArduCopter
|
|
|
|
# start with fmuv3 base port
|
|
include ../fmuv3/hwdef.dat
|
|
|
|
# remove some unnecessary features inherited from fmuv3
|
|
undef UART8
|
|
undef UART8_TX
|
|
undef UART8_RX
|
|
undef USART3
|
|
undef USART3_TX
|
|
undef USART3_RX
|
|
undef CAN1
|
|
undef CAN1_RX
|
|
undef CAN1_TX
|
|
undef CAN2
|
|
undef CAN2_RX
|
|
undef CAN2_TX
|
|
undef IOMCU_UART
|
|
undef AP_FEATURE_SBUS_OUT
|
|
undef HAL_OS_FATFS_IO
|
|
undef AP_FEATURE_RTSCTS
|
|
undef HAL_WITH_RAMTRON
|
|
undef IOMCU_UART
|
|
undef SDIO
|
|
undef HAL_BOARD_LOG_DIRECTORY
|
|
undef HAL_BOARD_TERRAIN_DIRECTORY
|
|
|
|
# short board name override (13 chars) to match original max length; can't change because name is used for transmitter bind CRC
|
|
define CHIBIOS_SHORT_BOARD_NAME "skyviper-v245"
|
|
|
|
SERIAL_ORDER OTG1 USART2 EMPTY UART4
|
|
|
|
# enable AP_Radio support
|
|
define HAL_RCINPUT_WITH_AP_RADIO 1
|
|
|
|
define HAL_GPIO_RADIO_RESET 1 // PB0 GPIO from FMU3
|
|
|
|
# setup for radio IRQ on PD15
|
|
undef PD15
|
|
PD15 MPU_DRDY INPUT GPIO(100)
|
|
define HAL_GPIO_RADIO_IRQ 100
|
|
|
|
# setup defines for ArduCopter config
|
|
define TOY_MODE_ENABLED ENABLED
|
|
define ARMING_DELAY_SEC 0
|
|
define LAND_START_ALT 700
|
|
define LAND_DETECTOR_ACCEL_MAX 2.0f
|
|
|
|
# support cypress and cc2500 radios
|
|
SPIDEV cypress SPI2 DEVID11 FRAM_CS MODE0 2*MHZ 2*MHZ
|
|
SPIDEV cc2500 SPI2 DEVID12 FRAM_CS MODE0 4*MHZ 4*MHZ
|
|
SPIDEV pixartflow SPI4 DEVID13 MPU_EXT_CS MODE3 2*MHZ 2*MHZ
|
|
|
|
# SPI2 for the cypress needs exclusive access or we will end up with
|
|
# lost packets
|
|
DMA_PRIORITY SPI2_* SPI* ADC*
|
|
DMA_NOSHARE SPI2_*
|
|
undef PA1
|
|
PA1 UART4_RX UART4 NODMA
|
|
|
|
# use flash storage
|
|
STORAGE_FLASH_PAGE 22
|
|
|
|
env DEFAULT_PARAMETERS 'Tools/Frame_params/SkyViper-2450GPS/defaults.parm'
|
|
|
|
# the web UI uses an abin file for firmware uploads
|
|
env BUILD_ABIN True
|
|
|
|
# Disable un-needed hardware drivers
|
|
define AP_AIRSPEED_ENABLED 0
|
|
define AP_OPTICALFLOW_ENABLED 0
|
|
define BEACON_ENABLED 0
|
|
define GPS_MOVING_BASELINE 0
|
|
define GRIPPER_ENABLED 0
|
|
define HAL_ADSB_SAGETECH_ENABLED 0
|
|
define HAL_ADSB_UAVIONIX_MAVLINK_ENABLED 0
|
|
define AP_AIS_ENABLED 0
|
|
define HAL_BATTMON_INA2XX_ENABLED 0
|
|
define AP_BATTMON_SMBUS_ENABLE 0
|
|
define HAL_CRSF_TELEM_ENABLED 0
|
|
define HAL_EFI_ENABLED 0
|
|
define HAL_EXTERNAL_AHRS_ENABLED 0
|
|
define HAL_GENERATOR_ENABLED 0
|
|
define HAL_HOTT_TELEM_ENABLED 0
|
|
define HAL_MOUNT_ENABLED 0
|
|
define HAL_MSP_SENSORS_ENABLED 0
|
|
define HAL_NMEA_OUTPUT_ENABLED 0
|
|
define HAL_PARACHUTE_ENABLED 0
|
|
define HAL_PICCOLO_CAN_ENABLE 0
|
|
define HAL_RUNCAM_ENABLED 0
|
|
define HAL_SMARTAUDIO_ENABLED 0
|
|
define HAL_SPEKTRUM_TELEM_ENABLED 0
|
|
define HAL_SPRAYER_ENABLED 0
|
|
define HAL_WITH_ESC_TELEM 0
|
|
define LANDING_GEAR_ENABLED 0
|
|
define MODE_TURTLE_ENABLED 0
|
|
define WINCH_ENABLED 0
|
|
define AP_ICENGINE_ENABLED 0
|
|
|
|
# serially-attached actuators aren't relevant on SkyViper:
|
|
define AP_FETTEC_ONEWIRE_ENABLED 0
|
|
define AP_ROBOTISSERVO_ENABLED 0
|
|
define AP_VOLZ_ENABLED 0
|
|
define HAL_SUPPORT_RCOUT_SERIAL 0
|
|
define HAL_TORQEEDO_ENABLED 0
|
|
|
|
# the SkyViper only has a single Baro:
|
|
define AP_BARO_BACKEND_DEFAULT_ENABLED 0
|
|
define AP_BARO_ICM20789_ENABLED 1
|
|
|
|
# SkyViper has only one physical GPS but can also take from mavlink:
|
|
define AP_GPS_BACKEND_DEFAULT_ENABLED 0
|
|
define AP_GPS_UBLOX_ENABLED 1
|
|
define AP_GPS_MAV_ENABLED 1
|
|
|
|
# enable only the QUAD frame
|
|
define AP_MOTORS_FRAME_DEFAULT_ENABLED 0
|
|
define AP_MOTORS_FRAME_QUAD_ENABLED 1
|
|
|
|
# SkyViper isn't going to sprout new compasses:
|
|
define COMPASS_MAX_SENSORS 1
|
|
define BARO_MAX_INSTANCES 1
|
|
define INS_MAX_INSTANCES 1
|
|
|
|
# SkyViper doesn't have any rangefinder, but might get mavlink?
|
|
define AP_RANGEFINDER_BACKEND_DEFAULT_ENABLED 0
|
|
define AP_RANGEFINDER_MAVLINK_ENABLED 1
|
|
|
|
AUTOBUILD_TARGETS Copter
|