ardupilot/libraries/AC_WPNav/AC_WPNav.cpp

1031 lines
41 KiB
C++

/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
#include <AP_HAL/AP_HAL.h>
#include "AC_WPNav.h"
extern const AP_HAL::HAL& hal;
const AP_Param::GroupInfo AC_WPNav::var_info[] PROGMEM = {
// index 0 was used for the old orientation matrix
// @Param: SPEED
// @DisplayName: Waypoint Horizontal Speed Target
// @Description: Defines the speed in cm/s which the aircraft will attempt to maintain horizontally during a WP mission
// @Units: cm/s
// @Range: 0 2000
// @Increment: 50
// @User: Standard
AP_GROUPINFO("SPEED", 0, AC_WPNav, _wp_speed_cms, WPNAV_WP_SPEED),
// @Param: RADIUS
// @DisplayName: Waypoint Radius
// @Description: Defines the distance from a waypoint, that when crossed indicates the wp has been hit.
// @Units: cm
// @Range: 100 1000
// @Increment: 1
// @User: Standard
AP_GROUPINFO("RADIUS", 1, AC_WPNav, _wp_radius_cm, WPNAV_WP_RADIUS),
// @Param: SPEED_UP
// @DisplayName: Waypoint Climb Speed Target
// @Description: Defines the speed in cm/s which the aircraft will attempt to maintain while climbing during a WP mission
// @Units: cm/s
// @Range: 0 1000
// @Increment: 50
// @User: Standard
AP_GROUPINFO("SPEED_UP", 2, AC_WPNav, _wp_speed_up_cms, WPNAV_WP_SPEED_UP),
// @Param: SPEED_DN
// @DisplayName: Waypoint Descent Speed Target
// @Description: Defines the speed in cm/s which the aircraft will attempt to maintain while descending during a WP mission
// @Units: cm/s
// @Range: 0 500
// @Increment: 10
// @User: Standard
AP_GROUPINFO("SPEED_DN", 3, AC_WPNav, _wp_speed_down_cms, WPNAV_WP_SPEED_DOWN),
// @Param: LOIT_SPEED
// @DisplayName: Loiter Horizontal Maximum Speed
// @Description: Defines the maximum speed in cm/s which the aircraft will travel horizontally while in loiter mode
// @Units: cm/s
// @Range: 0 2000
// @Increment: 50
// @User: Standard
AP_GROUPINFO("LOIT_SPEED", 4, AC_WPNav, _loiter_speed_cms, WPNAV_LOITER_SPEED),
// @Param: ACCEL
// @DisplayName: Waypoint Acceleration
// @Description: Defines the horizontal acceleration in cm/s/s used during missions
// @Units: cm/s/s
// @Range: 50 500
// @Increment: 10
// @User: Standard
AP_GROUPINFO("ACCEL", 5, AC_WPNav, _wp_accel_cms, WPNAV_ACCELERATION),
// @Param: ACCEL_Z
// @DisplayName: Waypoint Vertical Acceleration
// @Description: Defines the vertical acceleration in cm/s/s used during missions
// @Units: cm/s/s
// @Range: 50 500
// @Increment: 10
// @User: Standard
AP_GROUPINFO("ACCEL_Z", 6, AC_WPNav, _wp_accel_z_cms, WPNAV_WP_ACCEL_Z_DEFAULT),
// @Param: LOIT_JERK
// @DisplayName: Loiter maximum jerk
// @Description: Loiter maximum jerk in cm/s/s/s
// @Units: cm/s/s/s
// @Range: 500 2000
// @Increment: 1
// @User: Advanced
AP_GROUPINFO("LOIT_JERK", 7, AC_WPNav, _loiter_jerk_max_cmsss, WPNAV_LOITER_JERK_MAX_DEFAULT),
// @Param: LOIT_MAXA
// @DisplayName: Loiter maximum acceleration
// @Description: Loiter maximum acceleration in cm/s/s. Higher values cause the copter to accelerate and stop more quickly.
// @Units: cm/s/s
// @Range: 100 981
// @Increment: 1
// @User: Advanced
AP_GROUPINFO("LOIT_MAXA", 8, AC_WPNav, _loiter_accel_cmss, WPNAV_LOITER_ACCEL),
// @Param: LOIT_MINA
// @DisplayName: Loiter minimum acceleration
// @Description: Loiter minimum acceleration in cm/s/s. Higher values stop the copter more quickly when the stick is centered, but cause a larger jerk when the copter stops.
// @Units: cm/s/s
// @Range: 100 981
// @Increment: 1
// @User: Advanced
AP_GROUPINFO("LOIT_MINA", 9, AC_WPNav, _loiter_accel_min_cmss, WPNAV_LOITER_ACCEL_MIN),
AP_GROUPEND
};
// Default constructor.
// Note that the Vector/Matrix constructors already implicitly zero
// their values.
//
AC_WPNav::AC_WPNav(const AP_InertialNav& inav, const AP_AHRS& ahrs, AC_PosControl& pos_control, const AC_AttitudeControl& attitude_control) :
_inav(inav),
_ahrs(ahrs),
_pos_control(pos_control),
_attitude_control(attitude_control),
_loiter_step(0),
_pilot_accel_fwd_cms(0),
_pilot_accel_rgt_cms(0),
_wp_last_update(0),
_wp_step(0),
_track_length(0.0f),
_track_desired(0.0f),
_limited_speed_xy_cms(0.0f),
_track_accel(0.0f),
_track_speed(0.0f),
_track_leash_length(0.0f),
_slow_down_dist(0.0f),
_spline_time(0.0f),
_spline_time_scale(0.0f),
_spline_vel_scaler(0.0f),
_yaw(0.0f)
{
AP_Param::setup_object_defaults(this, var_info);
// init flags
_flags.reached_destination = false;
_flags.fast_waypoint = false;
_flags.slowing_down = false;
_flags.recalc_wp_leash = false;
_flags.new_wp_destination = false;
_flags.segment_type = SEGMENT_STRAIGHT;
}
///
/// loiter controller
///
/// init_loiter_target in cm from home
void AC_WPNav::init_loiter_target(const Vector3f& position, bool reset_I)
{
// initialise position controller
_pos_control.init_xy_controller(reset_I);
// initialise pos controller speed and acceleration
_pos_control.set_speed_xy(_loiter_speed_cms);
_pos_control.set_accel_xy(_loiter_accel_cmss);
// set target position
_pos_control.set_xy_target(position.x, position.y);
// initialise feed forward velocity to zero
_pos_control.set_desired_velocity_xy(0,0);
// initialise desired accel and add fake wind
_loiter_desired_accel.x = 0;
_loiter_desired_accel.y = 0;
// initialise pilot input
_pilot_accel_fwd_cms = 0;
_pilot_accel_rgt_cms = 0;
}
/// init_loiter_target - initialize's loiter position and feed-forward velocity from current pos and velocity
void AC_WPNav::init_loiter_target()
{
const Vector3f& curr_pos = _inav.get_position();
const Vector3f& curr_vel = _inav.get_velocity();
// initialise position controller
_pos_control.init_xy_controller();
// initialise pos controller speed and acceleration
_pos_control.set_speed_xy(_loiter_speed_cms);
_pos_control.set_accel_xy(_loiter_accel_cmss);
// set target position
_pos_control.set_xy_target(curr_pos.x, curr_pos.y);
// move current vehicle velocity into feed forward velocity
_pos_control.set_desired_velocity_xy(curr_vel.x, curr_vel.y);
// initialise desired accel and add fake wind
_loiter_desired_accel.x = (_loiter_accel_cmss)*curr_vel.x/_loiter_speed_cms;
_loiter_desired_accel.y = (_loiter_accel_cmss)*curr_vel.y/_loiter_speed_cms;
// initialise pilot input
_pilot_accel_fwd_cms = 0;
_pilot_accel_rgt_cms = 0;
}
/// loiter_soften_for_landing - reduce response for landing
void AC_WPNav::loiter_soften_for_landing()
{
const Vector3f& curr_pos = _inav.get_position();
// set target position to current position
_pos_control.set_xy_target(curr_pos.x, curr_pos.y);
_pos_control.freeze_ff_xy();
}
/// set_pilot_desired_acceleration - sets pilot desired acceleration from roll and pitch stick input
void AC_WPNav::set_pilot_desired_acceleration(float control_roll, float control_pitch)
{
// convert pilot input to desired acceleration in cm/s/s
_pilot_accel_fwd_cms = -control_pitch * _loiter_accel_cmss / 4500.0f;
_pilot_accel_rgt_cms = control_roll * _loiter_accel_cmss / 4500.0f;
}
/// get_loiter_stopping_point_xy - returns vector to stopping point based on a horizontal position and velocity
void AC_WPNav::get_loiter_stopping_point_xy(Vector3f& stopping_point) const
{
_pos_control.get_stopping_point_xy(stopping_point);
}
/// calc_loiter_desired_velocity - updates desired velocity (i.e. feed forward) with pilot requested acceleration and fake wind resistance
/// updated velocity sent directly to position controller
void AC_WPNav::calc_loiter_desired_velocity(float nav_dt, float ekfGndSpdLimit)
{
// calculate a loiter speed limit which is the minimum of the value set by the WPNAV_LOITER_SPEED
// parameter and the value set by the EKF to observe optical flow limits
float gnd_speed_limit_cms = min(_loiter_speed_cms,ekfGndSpdLimit*100.0f);
gnd_speed_limit_cms = max(gnd_speed_limit_cms, 10.0f);
// range check nav_dt
if( nav_dt < 0 ) {
return;
}
// check loiter speed and avoid divide by zero
if(gnd_speed_limit_cms < WPNAV_LOITER_SPEED_MIN) {
gnd_speed_limit_cms = WPNAV_LOITER_SPEED_MIN;
}
_pos_control.set_speed_xy(gnd_speed_limit_cms);
_pos_control.set_accel_xy(_loiter_accel_cmss);
// rotate pilot input to lat/lon frame
Vector2f desired_accel;
desired_accel.x = (_pilot_accel_fwd_cms*_ahrs.cos_yaw() - _pilot_accel_rgt_cms*_ahrs.sin_yaw());
desired_accel.y = (_pilot_accel_fwd_cms*_ahrs.sin_yaw() + _pilot_accel_rgt_cms*_ahrs.cos_yaw());
// calculate the difference
Vector2f des_accel_diff = (desired_accel - _loiter_desired_accel);
// constrain and scale the desired acceleration
float des_accel_change_total = pythagorous2(des_accel_diff.x, des_accel_diff.y);
float accel_change_max = _loiter_jerk_max_cmsss * nav_dt;
if (_loiter_jerk_max_cmsss > 0.0f && des_accel_change_total > accel_change_max && des_accel_change_total > 0.0f) {
des_accel_diff.x = accel_change_max * des_accel_diff.x/des_accel_change_total;
des_accel_diff.y = accel_change_max * des_accel_diff.y/des_accel_change_total;
}
// adjust the desired acceleration
_loiter_desired_accel += des_accel_diff;
// get pos_control's feed forward velocity
const Vector3f &desired_vel_3d = _pos_control.get_desired_velocity();
Vector2f desired_vel(desired_vel_3d.x,desired_vel_3d.y);
// add pilot commanded acceleration
desired_vel.x += _loiter_desired_accel.x * nav_dt;
desired_vel.y += _loiter_desired_accel.y * nav_dt;
float desired_speed = desired_vel.length();
if (!is_zero(desired_speed)) {
Vector2f desired_vel_norm = desired_vel/desired_speed;
float drag_speed_delta = -_loiter_accel_cmss*nav_dt*desired_speed/gnd_speed_limit_cms;
if (_pilot_accel_fwd_cms == 0 && _pilot_accel_rgt_cms == 0) {
drag_speed_delta = min(drag_speed_delta,-_loiter_accel_min_cmss*nav_dt);
}
desired_speed = max(desired_speed+drag_speed_delta,0.0f);
desired_vel = desired_vel_norm*desired_speed;
}
// Apply EKF limit to desired velocity - this limit is calculated by the EKF and adjusted as required to ensure certain sensor limits are respected (eg optical flow sensing)
float horizSpdDem = sqrtf(sq(desired_vel.x) + sq(desired_vel.y));
if (horizSpdDem > gnd_speed_limit_cms) {
desired_vel.x = desired_vel.x * gnd_speed_limit_cms / horizSpdDem;
desired_vel.y = desired_vel.y * gnd_speed_limit_cms / horizSpdDem;
}
// send adjusted feed forward velocity back to position controller
_pos_control.set_desired_velocity_xy(desired_vel.x,desired_vel.y);
}
/// get_bearing_to_target - get bearing to loiter target in centi-degrees
int32_t AC_WPNav::get_loiter_bearing_to_target() const
{
return get_bearing_cd(_inav.get_position(), _pos_control.get_pos_target());
}
// update_loiter - run the loiter controller - gets called at 100hz (APM) or 400hz (PX4)
void AC_WPNav::update_loiter(float ekfGndSpdLimit, float ekfNavVelGainScaler)
{
// calculate dt
float dt = _pos_control.time_since_last_xy_update();
// run at poscontrol update rate.
// TODO: run on user input to reduce latency, maybe if (user_input || dt >= _pos_control.get_dt_xy())
if (dt >= _pos_control.get_dt_xy()) {
// sanity check dt
if (dt >= 0.2f) {
dt = 0.0f;
}
calc_loiter_desired_velocity(dt,ekfGndSpdLimit);
_pos_control.update_xy_controller(AC_PosControl::XY_MODE_POS_LIMITED_AND_VEL_FF, ekfNavVelGainScaler);
}
}
/// init_brake_target - initializes stop position from current position and velocity
void AC_WPNav::init_brake_target(float accel_cmss)
{
const Vector3f& curr_vel = _inav.get_velocity();
Vector3f stopping_point;
// initialise position controller
_pos_control.init_xy_controller();
// initialise pos controller speed and acceleration
_pos_control.set_speed_xy(curr_vel.length());
_pos_control.set_accel_xy(accel_cmss);
_pos_control.calc_leash_length_xy();
_pos_control.get_stopping_point_xy(stopping_point);
// set target position
init_loiter_target(stopping_point);
}
// update_brake - run the stop controller - gets called at 400hz
void AC_WPNav::update_brake(float ekfGndSpdLimit, float ekfNavVelGainScaler)
{
// calculate dt
float dt = _pos_control.time_since_last_xy_update();
// run at poscontrol update rate.
if (dt >= _pos_control.get_dt_xy()) {
// send adjusted feed forward velocity back to position controller
_pos_control.set_desired_velocity_xy(0,0);
_pos_control.update_xy_controller(AC_PosControl::XY_MODE_POS_LIMITED_AND_VEL_FF, ekfNavVelGainScaler);
}
}
///
/// waypoint navigation
///
/// wp_and_spline_init - initialise straight line and spline waypoint controllers
/// updates target roll, pitch targets and I terms based on vehicle lean angles
/// should be called once before the waypoint controller is used but does not need to be called before subsequent updates to destination
void AC_WPNav::wp_and_spline_init()
{
// check _wp_accel_cms is reasonable
if (_wp_accel_cms <= 0) {
_wp_accel_cms.set_and_save(WPNAV_ACCELERATION);
}
// initialise position controller
_pos_control.init_xy_controller();
// initialise position controller speed and acceleration
_pos_control.set_speed_xy(_wp_speed_cms);
_pos_control.set_accel_xy(_wp_accel_cms);
_pos_control.set_speed_z(-_wp_speed_down_cms, _wp_speed_up_cms);
_pos_control.set_accel_z(_wp_accel_z_cms);
_pos_control.calc_leash_length_xy();
_pos_control.calc_leash_length_z();
}
/// set_speed_xy - allows main code to pass target horizontal velocity for wp navigation
void AC_WPNav::set_speed_xy(float speed_cms)
{
// range check new target speed and update position controller
if (speed_cms >= WPNAV_WP_SPEED_MIN) {
_wp_speed_cms = speed_cms;
_pos_control.set_speed_xy(_wp_speed_cms);
// flag that wp leash must be recalculated
_flags.recalc_wp_leash = true;
}
}
/// set_destination - set destination using cm from home
void AC_WPNav::set_wp_destination(const Vector3f& destination)
{
Vector3f origin;
// if waypoint controller is active use the existing position target as the origin
if ((hal.scheduler->millis() - _wp_last_update) < 1000) {
origin = _pos_control.get_pos_target();
} else {
// if waypoint controller is not active, set origin to reasonable stopping point (using curr pos and velocity)
_pos_control.get_stopping_point_xy(origin);
_pos_control.get_stopping_point_z(origin);
}
// set origin and destination
set_wp_origin_and_destination(origin, destination);
}
/// set_origin_and_destination - set origin and destination waypoints using position vectors (distance from home in cm)
void AC_WPNav::set_wp_origin_and_destination(const Vector3f& origin, const Vector3f& destination)
{
// store origin and destination locations
_origin = origin;
_destination = destination;
Vector3f pos_delta = _destination - _origin;
_track_length = pos_delta.length(); // get track length
// calculate each axis' percentage of the total distance to the destination
if (is_zero(_track_length)) {
// avoid possible divide by zero
_pos_delta_unit.x = 0;
_pos_delta_unit.y = 0;
_pos_delta_unit.z = 0;
}else{
_pos_delta_unit = pos_delta/_track_length;
}
// calculate leash lengths
calculate_wp_leash_length();
// initialise yaw heading
if (_track_length >= WPNAV_YAW_DIST_MIN) {
_yaw = get_bearing_cd(_origin, _destination);
} else {
// set target yaw to current heading. Alternatively we could pull this from the attitude controller if we had access to it
_yaw = _attitude_control.angle_ef_targets().z;
}
// initialise intermediate point to the origin
_pos_control.set_pos_target(origin);
_track_desired = 0; // target is at beginning of track
_flags.reached_destination = false;
_flags.fast_waypoint = false; // default waypoint back to slow
_flags.slowing_down = false; // target is not slowing down yet
_flags.segment_type = SEGMENT_STRAIGHT;
_flags.new_wp_destination = true; // flag new waypoint so we can freeze the pos controller's feed forward and smooth the transition
// initialise the limited speed to current speed along the track
const Vector3f &curr_vel = _inav.get_velocity();
// get speed along track (note: we convert vertical speed into horizontal speed equivalent)
float speed_along_track = curr_vel.x * _pos_delta_unit.x + curr_vel.y * _pos_delta_unit.y + curr_vel.z * _pos_delta_unit.z;
_limited_speed_xy_cms = constrain_float(speed_along_track,0,_wp_speed_cms);
}
/// shift_wp_origin_to_current_pos - shifts the origin and destination so the origin starts at the current position
/// used to reset the position just before takeoff
/// relies on set_wp_destination or set_wp_origin_and_destination having been called first
void AC_WPNav::shift_wp_origin_to_current_pos()
{
// return immediately if vehicle is not at the origin
if (_track_desired > 0.0f) {
return;
}
// get current and target locations
const Vector3f curr_pos = _inav.get_position();
const Vector3f pos_target = _pos_control.get_pos_target();
// calculate difference between current position and target
Vector3f pos_diff = curr_pos - pos_target;
// shift origin and destination
_origin += pos_diff;
_destination += pos_diff;
// move pos controller target and disable feed forward
_pos_control.set_pos_target(curr_pos);
_pos_control.freeze_ff_xy();
_pos_control.freeze_ff_z();
}
/// get_wp_stopping_point_xy - returns vector to stopping point based on a horizontal position and velocity
void AC_WPNav::get_wp_stopping_point_xy(Vector3f& stopping_point) const
{
_pos_control.get_stopping_point_xy(stopping_point);
}
/// advance_wp_target_along_track - move target location along track from origin to destination
void AC_WPNav::advance_wp_target_along_track(float dt)
{
float track_covered; // distance (in cm) along the track that the vehicle has traveled. Measured by drawing a perpendicular line from the track to the vehicle.
Vector3f track_error; // distance error (in cm) from the track_covered position (i.e. closest point on the line to the vehicle) and the vehicle
float track_desired_max; // the farthest distance (in cm) along the track that the leash will allow
float track_leash_slack; // additional distance (in cm) along the track from our track_covered position that our leash will allow
bool reached_leash_limit = false; // true when track has reached leash limit and we need to slow down the target point
// get current location
Vector3f curr_pos = _inav.get_position();
Vector3f curr_delta = curr_pos - _origin;
// calculate how far along the track we are
track_covered = curr_delta.x * _pos_delta_unit.x + curr_delta.y * _pos_delta_unit.y + curr_delta.z * _pos_delta_unit.z;
Vector3f track_covered_pos = _pos_delta_unit * track_covered;
track_error = curr_delta - track_covered_pos;
// calculate the horizontal error
float track_error_xy = pythagorous2(track_error.x, track_error.y);
// calculate the vertical error
float track_error_z = fabsf(track_error.z);
// get position control leash lengths
float leash_xy = _pos_control.get_leash_xy();
float leash_z;
if (track_error.z >= 0) {
leash_z = _pos_control.get_leash_up_z();
}else{
leash_z = _pos_control.get_leash_down_z();
}
// calculate how far along the track we could move the intermediate target before reaching the end of the leash
track_leash_slack = min(_track_leash_length*(leash_z-track_error_z)/leash_z, _track_leash_length*(leash_xy-track_error_xy)/leash_xy);
if (track_leash_slack < 0) {
track_desired_max = track_covered;
}else{
track_desired_max = track_covered + track_leash_slack;
}
// check if target is already beyond the leash
if (_track_desired > track_desired_max) {
reached_leash_limit = true;
}
// get current velocity
const Vector3f &curr_vel = _inav.get_velocity();
// get speed along track
float speed_along_track = curr_vel.x * _pos_delta_unit.x + curr_vel.y * _pos_delta_unit.y + curr_vel.z * _pos_delta_unit.z;
// calculate point at which velocity switches from linear to sqrt
float linear_velocity = _wp_speed_cms;
float kP = _pos_control.get_pos_xy_kP();
if (kP >= 0.0f) { // avoid divide by zero
linear_velocity = _track_accel/kP;
}
// let the limited_speed_xy_cms be some range above or below current velocity along track
if (speed_along_track < -linear_velocity) {
// we are traveling fast in the opposite direction of travel to the waypoint so do not move the intermediate point
_limited_speed_xy_cms = 0;
}else{
// increase intermediate target point's velocity if not yet at the leash limit
if(dt > 0 && !reached_leash_limit) {
_limited_speed_xy_cms += 2.0f * _track_accel * dt;
}
// do not allow speed to be below zero or over top speed
_limited_speed_xy_cms = constrain_float(_limited_speed_xy_cms, 0.0f, _track_speed);
// check if we should begin slowing down
if (!_flags.fast_waypoint) {
float dist_to_dest = _track_length - _track_desired;
if (!_flags.slowing_down && dist_to_dest <= _slow_down_dist) {
_flags.slowing_down = true;
}
// if target is slowing down, limit the speed
if (_flags.slowing_down) {
_limited_speed_xy_cms = min(_limited_speed_xy_cms, get_slow_down_speed(dist_to_dest, _track_accel));
}
}
// if our current velocity is within the linear velocity range limit the intermediate point's velocity to be no more than the linear_velocity above or below our current velocity
if (fabsf(speed_along_track) < linear_velocity) {
_limited_speed_xy_cms = constrain_float(_limited_speed_xy_cms,speed_along_track-linear_velocity,speed_along_track+linear_velocity);
}
}
// advance the current target
if (!reached_leash_limit) {
_track_desired += _limited_speed_xy_cms * dt;
// reduce speed if we reach end of leash
if (_track_desired > track_desired_max) {
_track_desired = track_desired_max;
_limited_speed_xy_cms -= 2.0f * _track_accel * dt;
if (_limited_speed_xy_cms < 0.0f) {
_limited_speed_xy_cms = 0.0f;
}
}
}
// do not let desired point go past the end of the track unless it's a fast waypoint
if (!_flags.fast_waypoint) {
_track_desired = constrain_float(_track_desired, 0, _track_length);
} else {
_track_desired = constrain_float(_track_desired, 0, _track_length + WPNAV_WP_FAST_OVERSHOOT_MAX);
}
// recalculate the desired position
_pos_control.set_pos_target(_origin + _pos_delta_unit * _track_desired);
// check if we've reached the waypoint
if( !_flags.reached_destination ) {
if( _track_desired >= _track_length ) {
// "fast" waypoints are complete once the intermediate point reaches the destination
if (_flags.fast_waypoint) {
_flags.reached_destination = true;
}else{
// regular waypoints also require the copter to be within the waypoint radius
Vector3f dist_to_dest = curr_pos - _destination;
if( dist_to_dest.length() <= _wp_radius_cm ) {
_flags.reached_destination = true;
}
}
}
}
}
/// get_wp_distance_to_destination - get horizontal distance to destination in cm
float AC_WPNav::get_wp_distance_to_destination() const
{
// get current location
Vector3f curr = _inav.get_position();
return pythagorous2(_destination.x-curr.x,_destination.y-curr.y);
}
/// get_wp_bearing_to_destination - get bearing to next waypoint in centi-degrees
int32_t AC_WPNav::get_wp_bearing_to_destination() const
{
return get_bearing_cd(_inav.get_position(), _destination);
}
/// update_wpnav - run the wp controller - should be called at 100hz or higher
void AC_WPNav::update_wpnav()
{
// calculate dt
float dt = _pos_control.time_since_last_xy_update();
// update at poscontrol update rate
if (dt >= _pos_control.get_dt_xy()) {
// sanity check dt
if (dt >= 0.2f) {
dt = 0.0f;
}
// advance the target if necessary
advance_wp_target_along_track(dt);
// freeze feedforwards during known discontinuities
// TODO: why always consider Z axis discontinuous?
if (_flags.new_wp_destination) {
_flags.new_wp_destination = false;
_pos_control.freeze_ff_xy();
}
_pos_control.freeze_ff_z();
_pos_control.update_xy_controller(AC_PosControl::XY_MODE_POS_ONLY, 1.0f);
check_wp_leash_length();
_wp_last_update = hal.scheduler->millis();
}
}
// check_wp_leash_length - check if waypoint leash lengths need to be recalculated
// should be called after _pos_control.update_xy_controller which may have changed the position controller leash lengths
void AC_WPNav::check_wp_leash_length()
{
// exit immediately if recalc is not required
if (_flags.recalc_wp_leash) {
calculate_wp_leash_length();
}
}
/// calculate_wp_leash_length - calculates horizontal and vertical leash lengths for waypoint controller
void AC_WPNav::calculate_wp_leash_length()
{
// length of the unit direction vector in the horizontal
float pos_delta_unit_xy = pythagorous2(_pos_delta_unit.x, _pos_delta_unit.y);
float pos_delta_unit_z = fabsf(_pos_delta_unit.z);
float speed_z;
float leash_z;
if (_pos_delta_unit.z >= 0.0f) {
speed_z = _wp_speed_up_cms;
leash_z = _pos_control.get_leash_up_z();
}else{
speed_z = _wp_speed_down_cms;
leash_z = _pos_control.get_leash_down_z();
}
// calculate the maximum acceleration, maximum velocity, and leash length in the direction of travel
if(is_zero(pos_delta_unit_z) && is_zero(pos_delta_unit_xy)){
_track_accel = 0;
_track_speed = 0;
_track_leash_length = WPNAV_LEASH_LENGTH_MIN;
}else if(is_zero(_pos_delta_unit.z)){
_track_accel = _wp_accel_cms/pos_delta_unit_xy;
_track_speed = _wp_speed_cms/pos_delta_unit_xy;
_track_leash_length = _pos_control.get_leash_xy()/pos_delta_unit_xy;
}else if(is_zero(pos_delta_unit_xy)){
_track_accel = _wp_accel_z_cms/pos_delta_unit_z;
_track_speed = speed_z/pos_delta_unit_z;
_track_leash_length = leash_z/pos_delta_unit_z;
}else{
_track_accel = min(_wp_accel_z_cms/pos_delta_unit_z, _wp_accel_cms/pos_delta_unit_xy);
_track_speed = min(speed_z/pos_delta_unit_z, _wp_speed_cms/pos_delta_unit_xy);
_track_leash_length = min(leash_z/pos_delta_unit_z, _pos_control.get_leash_xy()/pos_delta_unit_xy);
}
// calculate slow down distance (the distance from the destination when the target point should begin to slow down)
calc_slow_down_distance(_track_speed, _track_accel);
// set recalc leash flag to false
_flags.recalc_wp_leash = false;
}
///
/// spline methods
///
/// set_spline_destination waypoint using position vector (distance from home in cm)
/// stopped_at_start should be set to true if vehicle is stopped at the origin
/// seg_end_type should be set to stopped, straight or spline depending upon the next segment's type
/// next_destination should be set to the next segment's destination if the seg_end_type is SEGMENT_END_STRAIGHT or SEGMENT_END_SPLINE
void AC_WPNav::set_spline_destination(const Vector3f& destination, bool stopped_at_start, spline_segment_end_type seg_end_type, const Vector3f& next_destination)
{
Vector3f origin;
// if waypoint controller is active and copter has reached the previous waypoint use current pos target as the origin
if ((hal.scheduler->millis() - _wp_last_update) < 1000) {
origin = _pos_control.get_pos_target();
}else{
// otherwise calculate origin from the current position and velocity
_pos_control.get_stopping_point_xy(origin);
_pos_control.get_stopping_point_z(origin);
}
// set origin and destination
set_spline_origin_and_destination(origin, destination, stopped_at_start, seg_end_type, next_destination);
}
/// set_spline_origin_and_destination - set origin and destination waypoints using position vectors (distance from home in cm)
/// seg_type should be calculated by calling function based on the mission
void AC_WPNav::set_spline_origin_and_destination(const Vector3f& origin, const Vector3f& destination, bool stopped_at_start, spline_segment_end_type seg_end_type, const Vector3f& next_destination)
{
// mission is "active" if wpnav has been called recently and vehicle reached the previous waypoint
bool prev_segment_exists = (_flags.reached_destination && ((hal.scheduler->millis() - _wp_last_update) < 1000));
float dt = _pos_control.get_dt_xy();
// check _wp_accel_cms is reasonable to avoid divide by zero
if (_wp_accel_cms <= 0) {
_wp_accel_cms.set_and_save(WPNAV_ACCELERATION);
}
// segment start types
// stop - vehicle is not moving at origin
// straight-fast - vehicle is moving, previous segment is straight. vehicle will fly straight through the waypoint before beginning it's spline path to the next wp
// _flag.segment_type holds whether prev segment is straight vs spline but we don't know if it has a delay
// spline-fast - vehicle is moving, previous segment is splined, vehicle will fly through waypoint but previous segment should have it flying in the correct direction (i.e. exactly parallel to position difference vector from previous segment's origin to this segment's destination)
// calculate spline velocity at origin
if (stopped_at_start || !prev_segment_exists) {
// if vehicle is stopped at the origin, set origin velocity to 0.02 * distance vector from origin to destination
_spline_origin_vel = (destination - origin) * dt;
_spline_time = 0.0f;
_spline_vel_scaler = 0.0f;
}else{
// look at previous segment to determine velocity at origin
if (_flags.segment_type == SEGMENT_STRAIGHT) {
// previous segment is straight, vehicle is moving so vehicle should fly straight through the origin
// before beginning it's spline path to the next waypoint. Note: we are using the previous segment's origin and destination
_spline_origin_vel = (_destination - _origin);
_spline_time = 0.0f; // To-Do: this should be set based on how much overrun there was from straight segment?
_spline_vel_scaler = _pos_control.get_vel_target().length(); // start velocity target from current target velocity
}else{
// previous segment is splined, vehicle will fly through origin
// we can use the previous segment's destination velocity as this segment's origin velocity
// Note: previous segment will leave destination velocity parallel to position difference vector
// from previous segment's origin to this segment's destination)
_spline_origin_vel = _spline_destination_vel;
if (_spline_time > 1.0f && _spline_time < 1.1f) { // To-Do: remove hard coded 1.1f
_spline_time -= 1.0f;
}else{
_spline_time = 0.0f;
}
// Note: we leave _spline_vel_scaler as it was from end of previous segment
}
}
// calculate spline velocity at destination
switch (seg_end_type) {
case SEGMENT_END_STOP:
// if vehicle stops at the destination set destination velocity to 0.02 * distance vector from origin to destination
_spline_destination_vel = (destination - origin) * dt;
_flags.fast_waypoint = false;
break;
case SEGMENT_END_STRAIGHT:
// if next segment is straight, vehicle's final velocity should face along the next segment's position
_spline_destination_vel = (next_destination - destination);
_flags.fast_waypoint = true;
break;
case SEGMENT_END_SPLINE:
// if next segment is splined, vehicle's final velocity should face parallel to the line from the origin to the next destination
_spline_destination_vel = (next_destination - origin);
_flags.fast_waypoint = true;
break;
}
// code below ensures we don't get too much overshoot when the next segment is short
float vel_len = _spline_origin_vel.length() + _spline_destination_vel.length();
float pos_len = (destination - origin).length() * 4.0f;
if (vel_len > pos_len) {
// if total start+stop velocity is more than twice position difference
// use a scaled down start and stop velocityscale the start and stop velocities down
float vel_scaling = pos_len / vel_len;
// update spline calculator
update_spline_solution(origin, destination, _spline_origin_vel * vel_scaling, _spline_destination_vel * vel_scaling);
}else{
// update spline calculator
update_spline_solution(origin, destination, _spline_origin_vel, _spline_destination_vel);
}
// initialise yaw heading to current heading
_yaw = _attitude_control.angle_ef_targets().z;
// store origin and destination locations
_origin = origin;
_destination = destination;
// calculate slow down distance
calc_slow_down_distance(_wp_speed_cms, _wp_accel_cms);
// initialise intermediate point to the origin
_pos_control.set_pos_target(origin);
_flags.reached_destination = false;
_flags.segment_type = SEGMENT_SPLINE;
_flags.new_wp_destination = true; // flag new waypoint so we can freeze the pos controller's feed forward and smooth the transition
}
/// update_spline - update spline controller
void AC_WPNav::update_spline()
{
// exit immediately if this is not a spline segment
if (_flags.segment_type != SEGMENT_SPLINE) {
return;
}
float dt = _pos_control.time_since_last_xy_update();
// run at poscontrol update rate
if (dt >= _pos_control.get_dt_xy()) {
// sanity check dt
if (dt >= 0.2f) {
dt = 0.0f;
}
// advance the target if necessary
advance_spline_target_along_track(dt);
// freeze feedforwards during known discontinuities
// TODO: why always consider Z axis discontinuous?
if (_flags.new_wp_destination) {
_flags.new_wp_destination = false;
_pos_control.freeze_ff_xy();
}
_pos_control.freeze_ff_z();
// run horizontal position controller
_pos_control.update_xy_controller(AC_PosControl::XY_MODE_POS_ONLY, 1.0f);
_wp_last_update = hal.scheduler->millis();
}
}
/// update_spline_solution - recalculates hermite_spline_solution grid
/// relies on _spline_origin_vel, _spline_destination_vel and _origin and _destination
void AC_WPNav::update_spline_solution(const Vector3f& origin, const Vector3f& dest, const Vector3f& origin_vel, const Vector3f& dest_vel)
{
_hermite_spline_solution[0] = origin;
_hermite_spline_solution[1] = origin_vel;
_hermite_spline_solution[2] = -origin*3.0f -origin_vel*2.0f + dest*3.0f - dest_vel;
_hermite_spline_solution[3] = origin*2.0f + origin_vel -dest*2.0f + dest_vel;
}
/// advance_spline_target_along_track - move target location along track from origin to destination
void AC_WPNav::advance_spline_target_along_track(float dt)
{
if (!_flags.reached_destination) {
Vector3f target_pos, target_vel;
// update target position and velocity from spline calculator
calc_spline_pos_vel(_spline_time, target_pos, target_vel);
_pos_delta_unit = target_vel/target_vel.length();
calculate_wp_leash_length();
// get current location
Vector3f curr_pos = _inav.get_position();
Vector3f track_error = curr_pos - target_pos;
// calculate the horizontal error
float track_error_xy = pythagorous2(track_error.x, track_error.y);
// calculate the vertical error
float track_error_z = fabsf(track_error.z);
// get position control leash lengths
float leash_xy = _pos_control.get_leash_xy();
float leash_z;
if (track_error.z >= 0) {
leash_z = _pos_control.get_leash_up_z();
}else{
leash_z = _pos_control.get_leash_down_z();
}
// calculate how far along the track we could move the intermediate target before reaching the end of the leash
float track_leash_slack = min(_track_leash_length*(leash_z-track_error_z)/leash_z, _track_leash_length*(leash_xy-track_error_xy)/leash_xy);
if (track_leash_slack < 0.0f) {
track_leash_slack = 0.0f;
}
// update velocity
float spline_dist_to_wp = (_destination - target_pos).length();
float vel_limit = _wp_speed_cms;
if (!is_zero(dt)) {
vel_limit = min(vel_limit, track_leash_slack/dt);
}
// if within the stopping distance from destination, set target velocity to sqrt of distance * 2 * acceleration
if (!_flags.fast_waypoint && spline_dist_to_wp < _slow_down_dist) {
_spline_vel_scaler = safe_sqrt(spline_dist_to_wp * 2.0f * _wp_accel_cms);
}else if(_spline_vel_scaler < vel_limit) {
// increase velocity using acceleration
_spline_vel_scaler += _wp_accel_cms * dt;
}
// constrain target velocity
_spline_vel_scaler = constrain_float(_spline_vel_scaler, 0.0f, vel_limit);
// scale the spline_time by the velocity we've calculated vs the velocity that came out of the spline calculator
float target_vel_length = target_vel.length();
if (!is_zero(target_vel_length)) {
_spline_time_scale = _spline_vel_scaler/target_vel_length;
}
// update target position
_pos_control.set_pos_target(target_pos);
// update the yaw
_yaw = RadiansToCentiDegrees(atan2f(target_vel.y,target_vel.x));
// advance spline time to next step
_spline_time += _spline_time_scale*dt;
// we will reach the next waypoint in the next step so set reached_destination flag
// To-Do: is this one step too early?
if (_spline_time >= 1.0f) {
_flags.reached_destination = true;
}
}
}
// calc_spline_pos_vel_accel - calculates target position, velocity and acceleration for the given "spline_time"
/// relies on update_spline_solution being called when the segment's origin and destination were set
void AC_WPNav::calc_spline_pos_vel(float spline_time, Vector3f& position, Vector3f& velocity)
{
float spline_time_sqrd = spline_time * spline_time;
float spline_time_cubed = spline_time_sqrd * spline_time;
position = _hermite_spline_solution[0] + \
_hermite_spline_solution[1] * spline_time + \
_hermite_spline_solution[2] * spline_time_sqrd + \
_hermite_spline_solution[3] * spline_time_cubed;
velocity = _hermite_spline_solution[1] + \
_hermite_spline_solution[2] * 2.0f * spline_time + \
_hermite_spline_solution[3] * 3.0f * spline_time_sqrd;
}
///
/// shared methods
///
// get_bearing_cd - return bearing in centi-degrees between two positions
// To-Do: move this to math library
float AC_WPNav::get_bearing_cd(const Vector3f &origin, const Vector3f &destination) const
{
float bearing = 9000 + atan2f(-(destination.x-origin.x), destination.y-origin.y) * 5729.57795f;
if (bearing < 0) {
bearing += 36000;
}
return bearing;
}
/// calc_slow_down_distance - calculates distance before waypoint that target point should begin to slow-down assuming it is travelling at full speed
void AC_WPNav::calc_slow_down_distance(float speed_cms, float accel_cmss)
{
// protect against divide by zero
if (accel_cmss <= 0.0f) {
_slow_down_dist = 0.0f;
return;
}
// To-Do: should we use a combination of horizontal and vertical speeds?
// To-Do: update this automatically when speed or acceleration is changed
_slow_down_dist = speed_cms * speed_cms / (4.0f*accel_cmss);
}
/// get_slow_down_speed - returns target speed of target point based on distance from the destination (in cm)
float AC_WPNav::get_slow_down_speed(float dist_from_dest_cm, float accel_cmss)
{
// return immediately if distance is zero (or less)
if (dist_from_dest_cm <= 0) {
return WPNAV_WP_TRACK_SPEED_MIN;
}
// calculate desired speed near destination
float target_speed = safe_sqrt(dist_from_dest_cm * 4.0f * accel_cmss);
// ensure desired speed never becomes too low
if (target_speed < WPNAV_WP_TRACK_SPEED_MIN) {
return WPNAV_WP_TRACK_SPEED_MIN;
} else {
return target_speed;
}
}