mirror of https://github.com/ArduPilot/ardupilot
140 lines
3.4 KiB
Plaintext
140 lines
3.4 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for the JFB110 hardware
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1110
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H755xx
|
|
define CORE_CM7
|
|
#define SMPS_PWR
|
|
|
|
# crystal frequency 24MHz
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
# the location where the bootloader will put the firmware
|
|
# bootloader is installed at zero offset
|
|
FLASH_RESERVE_START_KB 0
|
|
# the H755 has 128k sectors
|
|
FLASH_BOOTLOADER_LOAD_KB 128
|
|
# with 2M flash we can afford to optimize for speed
|
|
FLASH_SIZE_KB 2048
|
|
HAL_STORAGE_SIZE 32768
|
|
|
|
env OPTIMIZE -Os
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 2
|
|
|
|
# USB setup
|
|
# USB_VENDOR 0x0A8E # JAE
|
|
# USB_PRODUCT 0x8888 # This is temp Number
|
|
USB_STRING_MANUFACTURER "Japan Aviation Electronics Industry Ltd."
|
|
USB_STRING_PRODUCT "JFB-110"
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 UART7 UART5 USART3
|
|
|
|
# serial port for stdout, set SERIAL7_PROTOCOL 0(none) when using
|
|
# The value for STDOUT_SERIAL is a serial device name, and must be for a
|
|
# serial device for which pins are defined in this file. For example, SD3
|
|
# is for USART3 (SD3 == "serial device 3" in ChibiOS).
|
|
STDOUT_SERIAL SD3
|
|
STDOUT_BAUDRATE 921600
|
|
|
|
# default to all pins low to avoid ESD issues
|
|
DEFAULTGPIO OUTPUT LOW PULLDOWN
|
|
|
|
# USB OTG1 SERIAL0
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# pins for SWD debugging
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# CS pins
|
|
PH3 SCHA63T_G_CS CS # SPI1_CS1
|
|
PH4 SCHA63T_A_CS CS # SPI1_CS2
|
|
PH5 MS5611_2_CS CS # SPI1_CS3
|
|
PG6 AT25512_CS CS # SPI1_CS4
|
|
PG7 FRAM_CS CS # SPI3_CS1
|
|
PF10 IIM42652_1_CS CS # SPI3_CS2
|
|
PH15 MS5611_1_CS CS # SPI4_CS1
|
|
PG15 IIM42652_2_CS CS # SPI4_CS2
|
|
|
|
# telem1
|
|
PE8 UART7_TX UART7
|
|
PE10 UART7_CTS UART7
|
|
PF6 UART7_RX UART7
|
|
PF8 UART7_RTS UART7
|
|
|
|
# telem2
|
|
PC12 UART5_TX UART5
|
|
PC9 UART5_CTS UART5
|
|
PD2 UART5_RX UART5
|
|
PC8 UART5_RTS UART5
|
|
|
|
# debug uart
|
|
PD8 USART3_TX USART3 NODMA
|
|
PD9 USART3_RX USART3 NODMA
|
|
|
|
# armed indication
|
|
PB10 nARMED OUTPUT HIGH # TP8
|
|
|
|
# This defines an output pin which will default to output HIGH. It is
|
|
# a pin that enables peripheral power on this board. It starts in the
|
|
# off state, then is pulled low to enable peripherals in
|
|
# peripheral_power_enable()
|
|
PG10 nVDD_5V_HIPOWER_EN OUTPUT HIGH
|
|
PG4 nVDD_5V_PERIPH_EN OUTPUT HIGH
|
|
PG12 VDD_3V3_SENSORS_EN OUTPUT LOW
|
|
PD4 VDD_3V3_SENSORS2_EN OUTPUT LOW
|
|
PD3 VDD_3V3_SENSORS3_EN OUTPUT LOW
|
|
#VDD_3V3_SENSORS4_EN OUTPUT LOW
|
|
#VDD_3V3_SD_CARD_EN OUTPUT LOW
|
|
|
|
# PWM output pins
|
|
# we need to disable DMA on the last 2 FMU channels
|
|
# as timer 12 doesn't have a TIMn_UP DMA option
|
|
PA2 PWMOUT1 OUTPUT LOW
|
|
PE6 PWMOUT2 OUTPUT LOW
|
|
PA7 PWMOUT3 OUTPUT LOW
|
|
PA6 PWMOUT4 OUTPUT LOW
|
|
PD15 PWMOUT5 OUTPUT LOW
|
|
PE9 PWMOUT6 OUTPUT LOW
|
|
PH11 PWMOUT7 OUTPUT LOW
|
|
PH10 PWMOUT8 OUTPUT LOW
|
|
PA10 PWMOUT9 OUTPUT LOW
|
|
PA9 PWMOUT10 OUTPUT LOW
|
|
PD14 PWMOUT11 OUTPUT LOW
|
|
PD13 PWMOUT12 OUTPUT LOW
|
|
PD12 PWMOUT13 OUTPUT LOW
|
|
PH9 PWMOUT14 OUTPUT LOW
|
|
PH12 PWMOUT15 OUTPUT LOW
|
|
PH6 PWMOUT16 OUTPUT LOW
|
|
PD11 PWM_OE OUTPUT HIGH
|
|
PD5 PWM_OE2 OUTPUT HIGH
|
|
|
|
# controlled manually
|
|
PG13 GPIO_CAN1_SILENT OUTPUT PUSHPULL HIGH
|
|
PG8 GPIO_CAN2_SILENT OUTPUT PUSHPULL HIGH
|
|
|
|
# Control of Spektrum power pin
|
|
PH2 SPEKTRUM_PWR OUTPUT LOW GPIO(69)
|
|
|
|
# LEDs
|
|
#PE3 LED_RED OUTPUT OPENDRAIN GPIO(70) HIGH
|
|
##PE4 LED_GREEN OUTPUT OPENDRAIN GPIO(71) LOW
|
|
##PE5 LED_BLUE OUTPUT OPENDRAIN GPIO(72) LOW
|
|
|
|
PE4 LED_BOOTLOADER OUTPUT HIGH
|
|
PE5 LED_ACTIVITY OUTPUT HIGH
|
|
define HAL_LED_ON 0
|
|
|
|
#define HAL_USE_EMPTY_STORAGE 1
|
|
#define HAL_STORAGE_SIZE 32768
|
|
|
|
# enable DFU by default
|
|
#ENABLE_DFU_BOOT 1
|