ardupilot/ArduPlane/navigation.cpp

422 lines
16 KiB
C++

#include "Plane.h"
/*
reset the total loiter angle
*/
void Plane::loiter_angle_reset(void)
{
loiter.sum_cd = 0;
loiter.total_cd = 0;
loiter.reached_target_alt = false;
loiter.unable_to_acheive_target_alt = false;
}
/*
update the total angle we have covered in a loiter. Used to support
commands to do N circles of loiter
*/
void Plane::loiter_angle_update(void)
{
static const int32_t lap_check_interval_cd = 3*36000;
const int32_t target_bearing_cd = nav_controller->target_bearing_cd();
int32_t loiter_delta_cd;
const bool reached_target = reached_loiter_target();
if (loiter.sum_cd == 0 && !reached_target) {
// we don't start summing until we are doing the real loiter
loiter_delta_cd = 0;
} else if (loiter.sum_cd == 0) {
// use 1 cd for initial delta
loiter_delta_cd = 1;
loiter.start_lap_alt_cm = current_loc.alt;
loiter.next_sum_lap_cd = lap_check_interval_cd;
} else {
loiter_delta_cd = target_bearing_cd - loiter.old_target_bearing_cd;
}
loiter.old_target_bearing_cd = target_bearing_cd;
loiter_delta_cd = wrap_180_cd(loiter_delta_cd);
loiter.sum_cd += loiter_delta_cd * loiter.direction;
bool reached_target_alt = false;
if (reached_target) {
// once we reach the position target we start checking the
// altitude target
bool terrain_status_ok = false;
#if AP_TERRAIN_AVAILABLE
/*
if doing terrain following then we check against terrain
target, fetch the terrain information
*/
float altitude_agl = 0;
if (target_altitude.terrain_following) {
if (terrain.status() == AP_Terrain::TerrainStatusOK &&
terrain.height_above_terrain(altitude_agl, true)) {
terrain_status_ok = true;
}
}
if (terrain_status_ok &&
fabsf(altitude_agl - target_altitude.terrain_alt_cm*0.01) < 5) {
reached_target_alt = true;
} else
#endif
if (!terrain_status_ok && labs(current_loc.alt - target_altitude.amsl_cm) < 500) {
reached_target_alt = true;
}
}
if (reached_target_alt) {
loiter.reached_target_alt = true;
loiter.unable_to_acheive_target_alt = false;
loiter.next_sum_lap_cd = loiter.sum_cd + lap_check_interval_cd;
} else if (!loiter.reached_target_alt && labs(loiter.sum_cd) >= loiter.next_sum_lap_cd) {
// check every few laps for scenario where up/downdrafts inhibit you from loitering up/down for too long
loiter.unable_to_acheive_target_alt = labs(current_loc.alt - loiter.start_lap_alt_cm) < 500;
loiter.start_lap_alt_cm = current_loc.alt;
loiter.next_sum_lap_cd += lap_check_interval_cd;
}
}
//****************************************************************
// Function that will calculate the desired direction to fly and distance
//****************************************************************
void Plane::navigate()
{
// do not navigate with corrupt data
// ---------------------------------
if (!have_position) {
return;
}
if (next_WP_loc.lat == 0 && next_WP_loc.lng == 0) {
return;
}
// waypoint distance from plane
// ----------------------------
auto_state.wp_distance = current_loc.get_distance(next_WP_loc);
auto_state.wp_proportion = current_loc.line_path_proportion(prev_WP_loc, next_WP_loc);
SpdHgt_Controller->set_path_proportion(auto_state.wp_proportion);
// update total loiter angle
loiter_angle_update();
// control mode specific updates to navigation demands
// ---------------------------------------------------
control_mode->navigate();
}
// method intended for use in calc_airspeed_errors only
float Plane::mode_auto_target_airspeed_cm()
{
#if HAL_QUADPLANE_ENABLED
if ((quadplane.options & QuadPlane::OPTION_MISSION_LAND_FW_APPROACH) &&
((vtol_approach_s.approach_stage == Landing_ApproachStage::APPROACH_LINE) ||
(vtol_approach_s.approach_stage == Landing_ApproachStage::VTOL_LANDING))) {
const float land_airspeed = SpdHgt_Controller->get_land_airspeed();
if (is_positive(land_airspeed)) {
return land_airspeed * 100;
}
// fallover to normal airspeed
return aparm.airspeed_cruise_cm;
}
if (quadplane.in_vtol_land_approach()) {
return quadplane.get_land_airspeed() * 100;
}
#endif
// normal AUTO mode and new_airspeed variable was set by
// DO_CHANGE_SPEED command while in AUTO mode
if (new_airspeed_cm > 0) {
return new_airspeed_cm;
}
// fallover to normal airspeed
return aparm.airspeed_cruise_cm;
}
void Plane::calc_airspeed_errors()
{
float airspeed_measured = 0;
// we use the airspeed estimate function not direct sensor as TECS
// may be using synthetic airspeed
ahrs.airspeed_estimate(airspeed_measured);
// FBW_B/cruise airspeed target
if (!failsafe.rc_failsafe && (control_mode == &mode_fbwb || control_mode == &mode_cruise)) {
if (g2.flight_options & FlightOptions::CRUISE_TRIM_AIRSPEED) {
target_airspeed_cm = aparm.airspeed_cruise_cm;
} else if (g2.flight_options & FlightOptions::CRUISE_TRIM_THROTTLE) {
float control_min = 0.0f;
float control_mid = 0.0f;
const float control_max = channel_throttle->get_range();
const float control_in = get_throttle_input();
switch (channel_throttle->get_type()) {
case RC_Channel::RC_CHANNEL_TYPE_ANGLE:
control_min = -control_max;
break;
case RC_Channel::RC_CHANNEL_TYPE_RANGE:
control_mid = channel_throttle->get_control_mid();
break;
}
if (control_in <= control_mid) {
target_airspeed_cm = linear_interpolate(aparm.airspeed_min * 100, aparm.airspeed_cruise_cm,
control_in,
control_min, control_mid);
} else {
target_airspeed_cm = linear_interpolate(aparm.airspeed_cruise_cm, aparm.airspeed_max * 100,
control_in,
control_mid, control_max);
}
} else {
target_airspeed_cm = ((int32_t)(aparm.airspeed_max - aparm.airspeed_min) *
get_throttle_input()) + ((int32_t)aparm.airspeed_min * 100);
}
#if OFFBOARD_GUIDED == ENABLED
} else if (control_mode == &mode_guided && guided_state.target_airspeed_cm > 0.0) { // if offbd guided speed change cmd not set, then this section is skipped
// offboard airspeed demanded
uint32_t now = AP_HAL::millis();
float delta = 1e-3f * (now - guided_state.target_airspeed_time_ms);
guided_state.target_airspeed_time_ms = now;
float delta_amt = 100 * delta * guided_state.target_airspeed_accel;
target_airspeed_cm += delta_amt;
//target_airspeed_cm recalculated then clamped to between MIN airspeed and MAX airspeed by constrain_float
if (is_positive(guided_state.target_airspeed_accel)) {
target_airspeed_cm = constrain_float(MIN(guided_state.target_airspeed_cm, target_airspeed_cm), aparm.airspeed_min *100, aparm.airspeed_max *100);
} else {
target_airspeed_cm = constrain_float(MAX(guided_state.target_airspeed_cm, target_airspeed_cm), aparm.airspeed_min *100, aparm.airspeed_max *100);
}
#endif // OFFBOARD_GUIDED == ENABLED
} else if (flight_stage == AP_Vehicle::FixedWing::FLIGHT_LAND) {
// Landing airspeed target
target_airspeed_cm = landing.get_target_airspeed_cm();
} else if (control_mode == &mode_guided && new_airspeed_cm > 0) { //DO_CHANGE_SPEED overrides onboard guided speed commands, user would have re-enter guided mode to revert
target_airspeed_cm = new_airspeed_cm;
} else if (control_mode == &mode_auto) {
target_airspeed_cm = mode_auto_target_airspeed_cm();
#if HAL_QUADPLANE_ENABLED
} else if (control_mode == &mode_qrtl && quadplane.in_vtol_land_approach()) {
target_airspeed_cm = quadplane.get_land_airspeed() * 100;
#endif
} else {
// Normal airspeed target for all other cases
target_airspeed_cm = aparm.airspeed_cruise_cm;
}
// Set target to current airspeed + ground speed undershoot,
// but only when this is faster than the target airspeed commanded
// above.
if (control_mode->does_auto_throttle() &&
aparm.min_gndspeed_cm > 0 &&
control_mode != &mode_circle) {
int32_t min_gnd_target_airspeed = airspeed_measured*100 + groundspeed_undershoot;
if (min_gnd_target_airspeed > target_airspeed_cm) {
target_airspeed_cm = min_gnd_target_airspeed;
}
}
// when using the special GUIDED mode features for slew control, don't allow airspeed nudging as it doesn't play nicely.
#if OFFBOARD_GUIDED == ENABLED
if (control_mode == &mode_guided && !is_zero(guided_state.target_airspeed_cm) && (airspeed_nudge_cm != 0)) {
airspeed_nudge_cm = 0; //airspeed_nudge_cm forced to zero
}
#endif
// Bump up the target airspeed based on throttle nudging
if (control_mode->allows_throttle_nudging() && airspeed_nudge_cm > 0) {
target_airspeed_cm += airspeed_nudge_cm;
}
// Apply airspeed limit
target_airspeed_cm = constrain_int32(target_airspeed_cm, aparm.airspeed_min*100, aparm.airspeed_max*100);
// use the TECS view of the target airspeed for reporting, to take
// account of the landing speed
airspeed_error = SpdHgt_Controller->get_target_airspeed() - airspeed_measured;
}
void Plane::calc_gndspeed_undershoot()
{
// Use the component of ground speed in the forward direction
// This prevents flyaway if wind takes plane backwards
if (gps.status() >= AP_GPS::GPS_OK_FIX_2D) {
Vector2f gndVel = ahrs.groundspeed_vector();
const Matrix3f &rotMat = ahrs.get_rotation_body_to_ned();
Vector2f yawVect = Vector2f(rotMat.a.x,rotMat.b.x);
if (!yawVect.is_zero()) {
yawVect.normalize();
float gndSpdFwd = yawVect * gndVel;
groundspeed_undershoot = (aparm.min_gndspeed_cm > 0) ? (aparm.min_gndspeed_cm - gndSpdFwd*100) : 0;
}
} else {
groundspeed_undershoot = 0;
}
}
// method intended to be used by update_loiter
void Plane::update_loiter_update_nav(uint16_t radius)
{
#if HAL_QUADPLANE_ENABLED
if (loiter.start_time_ms != 0 &&
quadplane.guided_mode_enabled()) {
if (!auto_state.vtol_loiter) {
auto_state.vtol_loiter = true;
// reset loiter start time, so we don't consider the point
// reached till we get much closer
loiter.start_time_ms = 0;
quadplane.guided_start();
}
return;
}
#endif
#if HAL_QUADPLANE_ENABLED
const bool quadplane_qrtl_switch = (control_mode == &mode_rtl && quadplane.available() && quadplane.rtl_mode == QuadPlane::RTL_MODE::SWITCH_QRTL);
#else
const bool quadplane_qrtl_switch = false;
#endif
if ((loiter.start_time_ms == 0 &&
(control_mode == &mode_auto || control_mode == &mode_guided) &&
auto_state.crosstrack &&
current_loc.get_distance(next_WP_loc) > radius*3) ||
quadplane_qrtl_switch) {
/*
if never reached loiter point and using crosstrack and somewhat far away from loiter point
navigate to it like in auto-mode for normal crosstrack behavior
we also use direct waypoint navigation if we are a quadplane
that is going to be switching to QRTL when it gets within
RTL_RADIUS
*/
nav_controller->update_waypoint(prev_WP_loc, next_WP_loc);
return;
}
nav_controller->update_loiter(next_WP_loc, radius, loiter.direction);
}
void Plane::update_loiter(uint16_t radius)
{
if (radius <= 1) {
// if radius is <=1 then use the general loiter radius. if it's small, use default
radius = (abs(aparm.loiter_radius) <= 1) ? LOITER_RADIUS_DEFAULT : abs(aparm.loiter_radius);
if (next_WP_loc.loiter_ccw == 1) {
loiter.direction = -1;
} else {
loiter.direction = (aparm.loiter_radius < 0) ? -1 : 1;
}
}
update_loiter_update_nav(radius);
if (loiter.start_time_ms == 0) {
if (reached_loiter_target() ||
auto_state.wp_proportion > 1) {
// we've reached the target, start the timer
loiter.start_time_ms = millis();
if (control_mode->is_guided_mode()) {
// starting a loiter in GUIDED means we just reached the target point
gcs().send_mission_item_reached_message(0);
}
#if HAL_QUADPLANE_ENABLED
if (quadplane.guided_mode_enabled()) {
quadplane.guided_start();
}
#endif
}
}
}
/*
handle speed and height control in FBWB or CRUISE mode.
In this mode the elevator is used to change target altitude. The
throttle is used to change target airspeed or throttle
*/
void Plane::update_fbwb_speed_height(void)
{
uint32_t now = micros();
if (now - target_altitude.last_elev_check_us >= 100000) {
// we don't run this on every loop as it would give too small granularity on quadplanes at 300Hz, and
// give below 1cm altitude change, which would result in no climb or descent
float dt = (now - target_altitude.last_elev_check_us) * 1.0e-6;
dt = constrain_float(dt, 0.1, 0.15);
target_altitude.last_elev_check_us = now;
float elevator_input = channel_pitch->get_control_in() / 4500.0f;
if (g.flybywire_elev_reverse) {
elevator_input = -elevator_input;
}
int32_t alt_change_cm = g.flybywire_climb_rate * elevator_input * dt * 100;
change_target_altitude(alt_change_cm);
if (is_zero(elevator_input) && !is_zero(target_altitude.last_elevator_input)) {
// the user has just released the elevator, lock in
// the current altitude
set_target_altitude_current();
}
#if HAL_SOARING_ENABLED
if (g2.soaring_controller.is_active()) {
if (g2.soaring_controller.get_throttle_suppressed()) {
// we're in soaring mode with throttle suppressed
set_target_altitude_current();
} else {
// we're in soaring mode climbing back to altitude. Set target to SOAR_ALT_CUTOFF plus 10m to ensure we positively climb
// through SOAR_ALT_CUTOFF, thus triggering throttle suppression and return to glide.
target_altitude.amsl_cm = 100*plane.g2.soaring_controller.get_alt_cutoff() + 1000 + AP::ahrs().get_home().alt;
}
}
#endif
target_altitude.last_elevator_input = elevator_input;
}
check_fbwb_minimum_altitude();
altitude_error_cm = calc_altitude_error_cm();
calc_throttle();
calc_nav_pitch();
}
/*
calculate the turn angle for the next leg of the mission
*/
void Plane::setup_turn_angle(void)
{
int32_t next_ground_course_cd = mission.get_next_ground_course_cd(-1);
if (next_ground_course_cd == -1) {
// the mission library can't determine a turn angle, assume 90 degrees
auto_state.next_turn_angle = 90.0f;
} else {
// get the heading of the current leg
int32_t ground_course_cd = prev_WP_loc.get_bearing_to(next_WP_loc);
// work out the angle we need to turn through
auto_state.next_turn_angle = wrap_180_cd(next_ground_course_cd - ground_course_cd) * 0.01f;
}
}
/*
see if we have reached our loiter target
*/
bool Plane::reached_loiter_target(void)
{
#if HAL_QUADPLANE_ENABLED
if (quadplane.in_vtol_auto()) {
return auto_state.wp_distance < 3;
}
#endif
return nav_controller->reached_loiter_target();
}