ardupilot/libraries/GCS_MAVLink/message_definitions/sensesoar.xml

84 lines
3.7 KiB
XML

<?xml version='1.0'?>
<mavlink>
<include>common.xml</include>
<enums>
<enum name="SENSESOAR_MODE">
<description> Different flight modes </description>
<entry name="SENSESOAR_MODE_GLIDING"> Gliding mode with motors off</entry>
<entry name="SENSESOAR_MODE_AUTONOMOUS"> Autonomous flight</entry>
<entry name="SENSESOAR_MODE_MANUAL"> RC controlled</entry>
</enum>
</enums>
<messages>
<message id="170" name="OBS_POSITION">
Position estimate of the observer in global frame
<field type="int32_t" name="lon">Longitude expressed in 1E7</field>
<field type="int32_t" name="lat">Latitude expressed in 1E7</field>
<field type="int32_t" name="alt">Altitude expressed in milimeters</field>
</message>
<message id="172" name="OBS_VELOCITY">
velocity estimate of the observer in NED inertial frame
<field type="float[3]" name="vel">Velocity</field>
</message>
<message id="174" name="OBS_ATTITUDE">
attitude estimate of the observer
<field type="double[4]" name="quat">Quaternion re;im</field>
</message>
<message id="176" name="OBS_WIND">
Wind estimate in NED inertial frame
<field type="float[3]" name="wind">Wind</field>
</message>
<message id="178" name="OBS_AIR_VELOCITY">
Estimate of the air velocity
<field type="float" name="magnitude">Air speed</field>
<field type="float" name="aoa">angle of attack</field>
<field type="float" name="slip">slip angle</field>
</message>
<message id="180" name="OBS_BIAS">
IMU biases
<field type="float[3]" name="accBias">accelerometer bias</field>
<field type="float[3]" name="gyroBias">gyroscope bias</field>
</message>
<message id="182" name="OBS_QFF">
estimate of the pressure at sea level
<field type="float" name="qff">Wind</field>
</message>
<message id="183" name="OBS_AIR_TEMP">
ambient air temperature
<field type="float" name="airT">Air Temperatur</field>
</message>
<message id="184" name="FILT_ROT_VEL">
filtered rotational velocity
<field type="float[3]" name="rotVel">rotational velocity</field>
</message>
<message id="186" name="LLC_OUT">
low level control output
<field type="int16_t[4]" name="servoOut">Servo signal</field>
<field type="int16_t[2]" name="MotorOut">motor signal</field>
</message>
<message id="188" name="PM_ELEC">
Power managment
<field type="float" name="PwCons">current power consumption</field>
<field type="float" name="BatStat">battery status</field>
<field type="float[3]" name="PwGen">Power generation from each module</field>
</message>
<message id="190" name="SYS_Stat">
system status
<field type="uint8_t" name="gps">gps status</field>
<field type="uint8_t" name="act">actuator status</field>
<field type="uint8_t" name="mod">module status</field>
<field type="uint8_t" name="commRssi">module status</field>
</message>
<message id="192" name="CMD_AIRSPEED_CHNG">
change commanded air speed
<field type="uint8_t" name="target">Target ID</field>
<field type="float" name="spCmd">commanded airspeed</field>
</message>
<message id="194" name="CMD_AIRSPEED_ACK">
accept change of airspeed
<field type="float" name="spCmd">commanded airspeed</field>
<field type="uint8_t" name="ack">0:ack, 1:nack</field>
</message>
</messages>
</mavlink>