ardupilot/libraries/AP_HAL_ChibiOS/hwdef/KakuteF7/hwdef.dat

137 lines
2.8 KiB
Plaintext

# hw definition file for processing by chibios_pins.py
# for Holybro KakuteF7 hardware.
@ thanks to betaflight for pin information
# MCU class and specific type
MCU STM32F7xx STM32F745xx
# board ID for firmware load
APJ_BOARD_ID 123
# crystal frequency, setup to use external oscillator
OSCILLATOR_HZ 8000000
define STM32_LSECLK 32768U
define STM32_LSEDRV (3U << 3U)
define STM32_PLLSRC STM32_PLLSRC_HSE
define STM32_PLLM_VALUE 8
define STM32_PLLN_VALUE 432
define STM32_PLLP_VALUE 2
define STM32_PLLQ_VALUE 9
FLASH_SIZE_KB 1024
# leave 2 sectors free
FLASH_RESERVE_START_KB 96
# board voltage
STM32_VDD 330U
# only one I2C bus
I2C_ORDER I2C1
# order of UARTs (and USB), USART3 should be in second place to map order with the board's silk screen
UART_ORDER OTG1 USART3 USART1 USART2 UART4
# PA10 IO-debug-console
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
PA2 LED0 OUTPUT LOW
# SPI1 for SDCard
PA4 SDCARD_CS CS
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
# SPI2 for MAX7456 OSD
PB12 MAX7456_CS CS
PB13 SPI2_SCK SPI2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2
# SPI4 for ICM20689
PE4 ICM20689_CS CS
PE2 SPI4_SCK SPI4
PE5 SPI4_MISO SPI4
PE6 SPI4_MOSI SPI4
# I2C1 for baro
PB6 I2C1_SCL I2C1
PB7 I2C1_SDA I2C1
PC3 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PC2 BATT_CURRENT_SENS ADC1 SCALE(1)
# define default battery setup
define HAL_BATT_VOLT_PIN 13
define HAL_BATT_CURR_PIN 12
define HAL_BATT_VOLT_SCALE 10.1
define HAL_BATT_CURR_SCALE 17.0
PC5 RSSI_ADC ADC1
# USART1
PA10 USART1_RX USART1
PA9 USART1_TX USART1
# USART2
PD5 USART2_TX USART2
PD6 USART2_RX USART2
# USART3 (GPS)
PB11 USART3_RX USART3
PB10 USART3_TX USART3
# UART4 (GPS2)
PA0 UART4_TX UART4
PA1 UART4_RX UART4
# UART6, RX only, for RCIN
PC7 TIM8_CH2 TIM8 RCININT FLOAT LOW
# UART7 USED BY ESC FROM ORIGINAL DESIGN
#PE7 UART7_RX UART7
PB0 TIM3_CH3 TIM3 PWM(1)
PB1 TIM3_CH4 TIM3 PWM(2)
PE9 TIM1_CH1 TIM1 PWM(3)
PE11 TIM1_CH2 TIM1 PWM(4)
DMA_PRIORITY S*
define HAL_STORAGE_SIZE 16384
define STORAGE_FLASH_PAGE 1
# spi devices
SPIDEV mpu6000 SPI4 DEVID1 ICM20689_CS MODE3 1*MHZ 4*MHZ
SPIDEV sdcard SPI1 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ
SPIDEV osd SPI2 DEVID4 MAX7456_CS MODE0 10*MHZ 10*MHZ
define HAL_BARO_DEFAULT HAL_BARO_BMP280_I2C
define HAL_BARO_BMP280_BUS 0
define HAL_BARO_BMP280_I2C_ADDR 0x76
# no built-in compass, but probe the i2c bus for all possible
# external compass types
define ALLOW_ARM_NO_COMPASS
define HAL_COMPASS_DEFAULT HAL_COMPASS_NONE
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
define HAL_I2C_INTERNAL_MASK 0
# probe for an invensense IMU
define HAL_INS_DEFAULT HAL_INS_MPU60XX_SPI
define HAL_INS_DEFAULT_ROTATION ROTATION_YAW_180
define HAL_OS_FATFS_IO 1
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
# setup for OSD
define OSD_ENABLED ENABLED
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin