mirror of https://github.com/ArduPilot/ardupilot
216 lines
6.5 KiB
Plaintext
216 lines
6.5 KiB
Plaintext
/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
#if FRAME_CONFIG == Y6_FRAME
|
|
|
|
#define YAW_DIRECTION 1
|
|
|
|
static void init_motors_out()
|
|
{
|
|
#if INSTANT_PWM == 0
|
|
APM_RC.SetFastOutputChannels(_BV(MOT_1) | _BV(MOT_2) | _BV(MOT_3) | _BV(MOT_4)
|
|
| _BV(MOT_5) | _BV(MOT_6));
|
|
#endif
|
|
}
|
|
|
|
static void motors_output_enable()
|
|
{
|
|
APM_RC.enable_out(MOT_1);
|
|
APM_RC.enable_out(MOT_2);
|
|
APM_RC.enable_out(MOT_3);
|
|
APM_RC.enable_out(MOT_4);
|
|
APM_RC.enable_out(MOT_5);
|
|
APM_RC.enable_out(MOT_6);
|
|
}
|
|
|
|
static void output_motors_armed()
|
|
{
|
|
int out_min = g.rc_3.radio_min;
|
|
int out_max = g.rc_3.radio_max;
|
|
|
|
// Throttle is 0 to 1000 only
|
|
g.rc_3.servo_out = constrain(g.rc_3.servo_out, 0, 800);
|
|
|
|
if(g.rc_3.servo_out > 0)
|
|
out_min = g.rc_3.radio_min + MINIMUM_THROTTLE;
|
|
|
|
g.rc_1.calc_pwm();
|
|
g.rc_2.calc_pwm();
|
|
g.rc_3.calc_pwm();
|
|
g.rc_4.calc_pwm();
|
|
|
|
// Multi-Wii Mix
|
|
//left
|
|
motor_out[MOT_2] = (g.rc_3.radio_out * g.top_bottom_ratio) + g.rc_1.pwm_out + (g.rc_2.pwm_out * 2 / 3); // LEFT TOP - CW
|
|
motor_out[MOT_3] = g.rc_3.radio_out + g.rc_1.pwm_out + (g.rc_2.pwm_out * 2 / 3); // BOTTOM_LEFT - CCW
|
|
//right
|
|
motor_out[MOT_5] = (g.rc_3.radio_out * g.top_bottom_ratio) - g.rc_1.pwm_out + (g.rc_2.pwm_out * 2 / 3); // RIGHT TOP - CW
|
|
motor_out[MOT_1] = g.rc_3.radio_out - g.rc_1.pwm_out + (g.rc_2.pwm_out * 2 / 3); // BOTTOM_RIGHT - CCW
|
|
//back
|
|
motor_out[MOT_6] = (g.rc_3.radio_out * g.top_bottom_ratio) - (g.rc_2.pwm_out * 4 / 3); // REAR TOP - CCW
|
|
motor_out[MOT_4] = g.rc_3.radio_out - (g.rc_2.pwm_out * 4 / 3); // BOTTOM_REAR - CW
|
|
|
|
//left
|
|
motor_out[MOT_2] -= YAW_DIRECTION * g.rc_4.pwm_out; // LEFT TOP - CW
|
|
motor_out[MOT_3] += YAW_DIRECTION * g.rc_4.pwm_out; // LEFT BOTTOM - CCW
|
|
//right
|
|
motor_out[MOT_5] -= YAW_DIRECTION * g.rc_4.pwm_out; // RIGHT TOP - CW
|
|
motor_out[MOT_1] += YAW_DIRECTION * g.rc_4.pwm_out; // RIGHT BOTTOM - CCW
|
|
//back
|
|
motor_out[MOT_6] += YAW_DIRECTION * g.rc_4.pwm_out; // REAR TOP - CCW
|
|
motor_out[MOT_4] -= YAW_DIRECTION * g.rc_4.pwm_out; // REAR BOTTOM - CW
|
|
|
|
|
|
/*
|
|
int roll_out = (float)g.rc_1.pwm_out * .866;
|
|
int pitch_out = g.rc_2.pwm_out / 2;
|
|
|
|
//left
|
|
motor_out[MOT_2] = ((g.rc_3.radio_out * g.top_bottom_ratio) + roll_out + pitch_out); // CCW TOP
|
|
motor_out[MOT_3] = g.rc_3.radio_out + roll_out + pitch_out; // CW
|
|
|
|
//right
|
|
motor_out[MOT_5] = ((g.rc_3.radio_out * g.top_bottom_ratio) - roll_out + pitch_out); // CCW TOP
|
|
motor_out[MOT_1] = g.rc_3.radio_out - roll_out + pitch_out; // CW
|
|
|
|
//back
|
|
motor_out[MOT_6] = ((g.rc_3.radio_out * g.top_bottom_ratio) - g.rc_2.pwm_out); // CCW TOP
|
|
motor_out[MOT_4] = g.rc_3.radio_out - g.rc_2.pwm_out; // CW
|
|
|
|
// Yaw
|
|
//top
|
|
motor_out[MOT_2] += g.rc_4.pwm_out; // CCW
|
|
motor_out[MOT_5] += g.rc_4.pwm_out; // CCW
|
|
motor_out[MOT_6] += g.rc_4.pwm_out; // CCW
|
|
|
|
//bottom
|
|
motor_out[MOT_3] -= g.rc_4.pwm_out; // CW
|
|
motor_out[MOT_1] -= g.rc_4.pwm_out; // CW
|
|
motor_out[MOT_4] -= g.rc_4.pwm_out; // CW
|
|
*/
|
|
|
|
// TODO: add stability patch
|
|
motor_out[MOT_1] = min(motor_out[MOT_1], out_max);
|
|
motor_out[MOT_2] = min(motor_out[MOT_2], out_max);
|
|
motor_out[MOT_3] = min(motor_out[MOT_3], out_max);
|
|
motor_out[MOT_4] = min(motor_out[MOT_4], out_max);
|
|
motor_out[MOT_5] = min(motor_out[MOT_5], out_max);
|
|
motor_out[MOT_6] = min(motor_out[MOT_6], out_max);
|
|
|
|
// limit output so motors don't stop
|
|
motor_out[MOT_1] = max(motor_out[MOT_1], out_min);
|
|
motor_out[MOT_2] = max(motor_out[MOT_2], out_min);
|
|
motor_out[MOT_3] = max(motor_out[MOT_3], out_min);
|
|
motor_out[MOT_4] = max(motor_out[MOT_4], out_min);
|
|
motor_out[MOT_5] = max(motor_out[MOT_5], out_min);
|
|
motor_out[MOT_6] = max(motor_out[MOT_6], out_min);
|
|
|
|
#if CUT_MOTORS == ENABLED
|
|
// if we are not sending a throttle output, we cut the motors
|
|
if(g.rc_3.servo_out == 0){
|
|
motor_out[MOT_1] = g.rc_3.radio_min;
|
|
motor_out[MOT_2] = g.rc_3.radio_min;
|
|
motor_out[MOT_3] = g.rc_3.radio_min;
|
|
motor_out[MOT_4] = g.rc_3.radio_min;
|
|
motor_out[MOT_5] = g.rc_3.radio_min;
|
|
motor_out[MOT_6] = g.rc_3.radio_min;
|
|
}
|
|
#endif
|
|
|
|
// this filter slows the acceleration of motors vs the deceleration
|
|
// Idea by Denny Rowland to help with his Yaw issue
|
|
for(int8_t m = 0; m <= 6; m++){
|
|
int i = ch_of_mot(m);
|
|
if(motor_filtered[i] < motor_out[i]){
|
|
motor_filtered[i] = (motor_out[i] + motor_filtered[i]) / 2;
|
|
}else{
|
|
// don't filter
|
|
motor_filtered[i] = motor_out[i];
|
|
}
|
|
}
|
|
|
|
APM_RC.OutputCh(MOT_1, motor_filtered[MOT_1]);
|
|
APM_RC.OutputCh(MOT_2, motor_filtered[MOT_2]);
|
|
APM_RC.OutputCh(MOT_3, motor_filtered[MOT_3]);
|
|
APM_RC.OutputCh(MOT_4, motor_filtered[MOT_4]);
|
|
APM_RC.OutputCh(MOT_5, motor_filtered[MOT_5]);
|
|
APM_RC.OutputCh(MOT_6, motor_filtered[MOT_6]);
|
|
|
|
#if INSTANT_PWM == 1
|
|
// InstantPWM
|
|
APM_RC.Force_Out0_Out1();
|
|
APM_RC.Force_Out2_Out3();
|
|
APM_RC.Force_Out6_Out7();
|
|
#endif
|
|
}
|
|
|
|
static void output_motors_disarmed()
|
|
{
|
|
if(g.rc_3.control_in > 0){
|
|
// we have pushed up the throttle
|
|
// remove safety
|
|
motor_auto_armed = true;
|
|
}
|
|
|
|
// fill the motor_out[] array for HIL use
|
|
for (unsigned char i = 0; i < 8; i++){
|
|
motor_out[i] = g.rc_3.radio_min;
|
|
}
|
|
|
|
// Send commands to motors
|
|
APM_RC.OutputCh(MOT_1, g.rc_3.radio_min);
|
|
APM_RC.OutputCh(MOT_2, g.rc_3.radio_min);
|
|
APM_RC.OutputCh(MOT_3, g.rc_3.radio_min);
|
|
APM_RC.OutputCh(MOT_4, g.rc_3.radio_min);
|
|
APM_RC.OutputCh(MOT_5, g.rc_3.radio_min);
|
|
APM_RC.OutputCh(MOT_6, g.rc_3.radio_min);
|
|
}
|
|
|
|
static void output_motor_test()
|
|
{
|
|
motor_out[MOT_1] = g.rc_3.radio_min;
|
|
motor_out[MOT_2] = g.rc_3.radio_min;
|
|
motor_out[MOT_3] = g.rc_3.radio_min;
|
|
motor_out[MOT_4] = g.rc_3.radio_min;
|
|
motor_out[MOT_5] = g.rc_3.radio_min;
|
|
motor_out[MOT_6] = g.rc_3.radio_min;
|
|
|
|
APM_RC.OutputCh(MOT_1, g.rc_3.radio_min);
|
|
delay(5000);
|
|
APM_RC.OutputCh(MOT_2, g.rc_3.radio_min + 100);
|
|
delay(300);
|
|
|
|
APM_RC.OutputCh(MOT_2, g.rc_3.radio_min);
|
|
delay(3000);
|
|
APM_RC.OutputCh(MOT_3, g.rc_3.radio_min + 100);
|
|
delay(300);
|
|
|
|
APM_RC.OutputCh(MOT_3, g.rc_3.radio_min);
|
|
delay(3000);
|
|
APM_RC.OutputCh(MOT_6, g.rc_3.radio_min + 100);
|
|
delay(300);
|
|
|
|
APM_RC.OutputCh(MOT_6, g.rc_3.radio_min);
|
|
delay(3000);
|
|
APM_RC.OutputCh(MOT_4, g.rc_3.radio_min + 100);
|
|
delay(300);
|
|
|
|
APM_RC.OutputCh(MOT_4, g.rc_3.radio_min);
|
|
delay(3000);
|
|
APM_RC.OutputCh(MOT_5, g.rc_3.radio_min + 100);
|
|
delay(300);
|
|
|
|
APM_RC.OutputCh(MOT_5, g.rc_3.radio_min);
|
|
delay(3000);
|
|
APM_RC.OutputCh(MOT_1, g.rc_3.radio_min + 100);
|
|
delay(300);
|
|
|
|
APM_RC.OutputCh(MOT_1, motor_out[MOT_1]);
|
|
APM_RC.OutputCh(MOT_2, motor_out[MOT_2]);
|
|
APM_RC.OutputCh(MOT_3, motor_out[MOT_4]);
|
|
APM_RC.OutputCh(MOT_4, motor_out[MOT_4]);
|
|
APM_RC.OutputCh(MOT_5, motor_out[MOT_5]);
|
|
APM_RC.OutputCh(MOT_6, motor_out[MOT_6]);
|
|
}
|
|
|
|
#endif
|