mirror of https://github.com/ArduPilot/ardupilot
137 lines
2.8 KiB
Plaintext
137 lines
2.8 KiB
Plaintext
# hw definition file for processing by chibios_pins.py
|
|
# SuccexF4
|
|
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
HAL_CHIBIOS_ARCH_F405 1
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1011
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
STM32_ST_USE_TIMER 5
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 1024
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
# ADC
|
|
PC1 BAT_CURR_SENS ADC1 SCALE(1)
|
|
PC2 BAT_VOLT_SENS ADC1 SCALE(1)
|
|
|
|
# PWM outputs
|
|
PB0 TIM1_CH2N TIM1 PWM(1) GPIO(50)
|
|
PB1 TIM1_CH3N TIM1 PWM(2) GPIO(51)
|
|
PC9 TIM8_CH4 TIM8 PWM(3) GPIO(52)
|
|
PC8 TIM8_CH3 TIM8 PWM(4) GPIO(53)
|
|
|
|
# Two IMUs on SPI1
|
|
PC4 ICM20689_1_DRDY INPUT
|
|
PA8 ICM20689_2_DRDY INPUT
|
|
PA4 ICM20689_1_CS CS
|
|
PC3 ICM20689_2_CS CS
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# OSD on SPI2
|
|
PB12 AT7456E_CS CS
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
# FLASH on SPI3
|
|
PA15 FLASH_CS CS
|
|
PC10 SPI3_SCK SPI3
|
|
PC11 SPI3_MISO SPI3
|
|
PC12 SPI3_MOSI SPI3
|
|
|
|
# Order of I2C buses
|
|
I2C_ORDER I2C1
|
|
|
|
# UART ports and I2C bus
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 USART6
|
|
|
|
# Note that this board needs pull-ups on I2C pins
|
|
PB8 I2C1_SCL I2C1 PULLUP
|
|
PB9 I2C1_SDA I2C1 PULLUP
|
|
|
|
PA10 USART1_RX USART1
|
|
PA9 USART1_TX USART1
|
|
|
|
PA3 USART2_RX USART2
|
|
PA2 USART2_TX USART2
|
|
|
|
PB11 USART3_RX USART3
|
|
PB10 USART3_TX USART3
|
|
|
|
PC7 USART6_RX USART6
|
|
PC6 USART6_TX USART6
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# LED and buzzer
|
|
PB4 TIM3_CH1 TIM3 GPIO(56) ALARM
|
|
PB5 LED OUTPUT HIGH GPIO(57)
|
|
define HAL_GPIO_A_LED_PIN 57
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
PC5 VBUS INPUT OPENDRAIN
|
|
|
|
# LED strip pad as RC input
|
|
PB6 TIM4_CH1 TIM4 RCININT PULLDOWN LOW
|
|
|
|
# SPI Device table
|
|
SPIDEV icm20689_1 SPI1 DEVID1 ICM20689_1_CS MODE3 1*MHZ 8*MHZ
|
|
SPIDEV icm20689_2 SPI1 DEVID2 ICM20689_2_CS MODE3 1*MHZ 8*MHZ
|
|
SPIDEV osd SPI2 DEVID3 AT7456E_CS MODE0 10*MHZ 10*MHZ
|
|
SPIDEV dataflash SPI3 DEVID4 FLASH_CS MODE3 32*MHZ 32*MHZ
|
|
|
|
# Two IMUs
|
|
IMU Invensense SPI:icm20689_1 ROTATION_YAW_270
|
|
IMU Invensense SPI:icm20689_2 ROTATION_NONE
|
|
|
|
# one baro
|
|
BARO BMP280 I2C:0:0x76
|
|
define HAL_PROBE_EXTERNAL_I2C_BAROS
|
|
define HAL_BARO_ALLOW_INIT_NO_BARO
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
# external compass types
|
|
define ALLOW_ARM_NO_COMPASS
|
|
define HAL_COMPASS_DEFAULT HAL_COMPASS_NONE
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
define STORAGE_FLASH_PAGE 1
|
|
define HAL_STORAGE_SIZE 15360
|
|
|
|
# enable logging to dataflash
|
|
define HAL_LOGGING_DATAFLASH
|
|
|
|
# define default battery setup
|
|
define HAL_BATT_VOLT_PIN 12
|
|
define HAL_BATT_CURR_PIN 11
|
|
define HAL_BATT_VOLT_SCALE 11
|
|
define HAL_BATT_CURR_SCALE 18.2
|
|
|
|
define OSD_ENABLED 1
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
|
|
define BOARD_PWM_COUNT_DEFAULT 4
|
|
|
|
#font for the osd
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
|
|
|
# disable parachute and sprayer to save flash
|
|
define HAL_PARACHUTE_ENABLED 0
|
|
define HAL_SPRAYER_ENABLED 0
|
|
|
|
# reduce max size of embedded params for apj_tool.py
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 1024
|