ardupilot/ArduCopter/motor_test.cpp

199 lines
6.6 KiB
C++

#include "Copter.h"
/*
mavlink motor test - implements the MAV_CMD_DO_MOTOR_TEST mavlink command so that the GCS/pilot can test an individual motor or flaps
to ensure proper wiring, rotation.
*/
// motor test definitions
#define MOTOR_TEST_PWM_MIN 800 // min pwm value accepted by the test
#define MOTOR_TEST_PWM_MAX 2200 // max pwm value accepted by the test
#define MOTOR_TEST_TIMEOUT_MS_MAX 30000 // max timeout is 30 seconds
static uint32_t motor_test_start_ms; // system time the motor test began
static uint32_t motor_test_timeout_ms; // test will timeout this many milliseconds after the motor_test_start_ms
static uint8_t motor_test_seq; // motor sequence number of motor being tested
static uint8_t motor_test_count; // number of motors to test
static uint8_t motor_test_throttle_type; // motor throttle type (0=throttle percentage, 1=PWM, 2=pilot throttle channel pass-through)
static uint16_t motor_test_throttle_value; // throttle to be sent to motor, value depends upon it's type
// motor_test_output - checks for timeout and sends updates to motors objects
void Copter::motor_test_output()
{
// exit immediately if the motor test is not running
if (!ap.motor_test) {
return;
}
// check for test timeout
uint32_t now = AP_HAL::millis();
if ((now - motor_test_start_ms) >= motor_test_timeout_ms) {
if (motor_test_count > 1) {
if (now - motor_test_start_ms < motor_test_timeout_ms*1.5) {
// output zero for 50% of the test time
motors->output_min();
} else {
// move onto next motor
motor_test_seq++;
motor_test_count--;
motor_test_start_ms = now;
if (!motors->armed()) {
motors->armed(true);
}
}
return;
}
// stop motor test
motor_test_stop();
} else {
int16_t pwm = 0; // pwm that will be output to the motors
// calculate pwm based on throttle type
switch (motor_test_throttle_type) {
case MOTOR_TEST_THROTTLE_PERCENT:
// sanity check motor_test_throttle value
#if FRAME_CONFIG != HELI_FRAME
if (motor_test_throttle_value <= 100) {
int16_t pwm_min = motors->get_pwm_output_min();
int16_t pwm_max = motors->get_pwm_output_max();
pwm = pwm_min + (pwm_max - pwm_min) * (float)motor_test_throttle_value/100.0f;
}
#endif
break;
case MOTOR_TEST_THROTTLE_PWM:
pwm = motor_test_throttle_value;
break;
case MOTOR_TEST_THROTTLE_PILOT:
pwm = channel_throttle->get_radio_in();
break;
default:
motor_test_stop();
return;
}
// sanity check throttle values
if (pwm >= MOTOR_TEST_PWM_MIN && pwm <= MOTOR_TEST_PWM_MAX ) {
// turn on motor to specified pwm vlaue
motors->output_test(motor_test_seq, pwm);
} else {
motor_test_stop();
}
}
}
// mavlink_motor_test_check - perform checks before motor tests can begin
// return true if tests can continue, false if not
bool Copter::mavlink_motor_test_check(mavlink_channel_t chan, bool check_rc)
{
GCS_MAVLINK_Copter &gcs_chan = gcs().chan(chan-MAVLINK_COMM_0);
// check board has initialised
if (!ap.initialised) {
gcs_chan.send_text(MAV_SEVERITY_CRITICAL,"Motor Test: Board initialising");
return false;
}
// check rc has been calibrated
if (check_rc && !arming.rc_calibration_checks(true)) {
gcs_chan.send_text(MAV_SEVERITY_CRITICAL,"Motor Test: RC not calibrated");
return false;
}
// ensure we are landed
if (!ap.land_complete) {
gcs_chan.send_text(MAV_SEVERITY_CRITICAL,"Motor Test: vehicle not landed");
return false;
}
// check if safety switch has been pushed
if (hal.util->safety_switch_state() == AP_HAL::Util::SAFETY_DISARMED) {
gcs_chan.send_text(MAV_SEVERITY_CRITICAL,"Motor Test: Safety switch");
return false;
}
// if we got this far the check was successful and the motor test can continue
return true;
}
// mavlink_motor_test_start - start motor test - spin a single motor at a specified pwm
// returns MAV_RESULT_ACCEPTED on success, MAV_RESULT_FAILED on failure
MAV_RESULT Copter::mavlink_motor_test_start(mavlink_channel_t chan, uint8_t motor_seq, uint8_t throttle_type, uint16_t throttle_value,
float timeout_sec, uint8_t motor_count)
{
if (motor_count == 0) {
motor_count = 1;
}
// if test has not started try to start it
if (!ap.motor_test) {
/* perform checks that it is ok to start test
The RC calibrated check can be skipped if direct pwm is
supplied
*/
if (!mavlink_motor_test_check(chan, throttle_type != 1)) {
return MAV_RESULT_FAILED;
} else {
// start test
ap.motor_test = true;
// enable and arm motors
if (!motors->armed()) {
init_rc_out();
enable_motor_output();
motors->armed(true);
}
// disable throttle, battery and gps failsafe
g.failsafe_throttle = FS_THR_DISABLED;
g.failsafe_battery_enabled = FS_BATT_DISABLED;
g.failsafe_gcs = FS_GCS_DISABLED;
// turn on notify leds
AP_Notify::flags.esc_calibration = true;
}
}
// set timeout
motor_test_start_ms = AP_HAL::millis();
motor_test_timeout_ms = MIN(timeout_sec * 1000, MOTOR_TEST_TIMEOUT_MS_MAX);
// store required output
motor_test_seq = motor_seq;
motor_test_count = motor_count;
motor_test_throttle_type = throttle_type;
motor_test_throttle_value = throttle_value;
// return success
return MAV_RESULT_ACCEPTED;
}
// motor_test_stop - stops the motor test
void Copter::motor_test_stop()
{
// exit immediately if the test is not running
if (!ap.motor_test) {
return;
}
// flag test is complete
ap.motor_test = false;
// disarm motors
motors->armed(false);
// reset timeout
motor_test_start_ms = 0;
motor_test_timeout_ms = 0;
// re-enable failsafes
g.failsafe_throttle.load();
g.failsafe_battery_enabled.load();
g.failsafe_gcs.load();
// turn off notify leds
AP_Notify::flags.esc_calibration = false;
}