mirror of https://github.com/ArduPilot/ardupilot
162 lines
3.8 KiB
Plaintext
162 lines
3.8 KiB
Plaintext
# hw definition file for HEEWING F405
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
# bootloader starts firmware at 64k
|
|
FLASH_RESERVE_START_KB 64
|
|
FLASH_SIZE_KB 1024
|
|
|
|
# store parameters in pages 1 and 2
|
|
STORAGE_FLASH_PAGE 1
|
|
define HAL_STORAGE_SIZE 15360
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1119
|
|
|
|
define STM32_ST_USE_TIMER 5
|
|
define CH_CFG_ST_RESOLUTION 32
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
# --------------------- LED -----------------------
|
|
define AP_NOTIFY_GPIO_LED_2_ENABLED 1
|
|
PC13 LED0 OUTPUT LOW GPIO(90) # blue marked as ACT
|
|
PC15 LED1 OUTPUT LOW GPIO(91) # green marked as B/E
|
|
define HAL_GPIO_A_LED_PIN 91
|
|
define HAL_GPIO_B_LED_PIN 90
|
|
|
|
|
|
# --------------------- PWM -----------------------
|
|
|
|
PB7 TIM4_CH2 TIM4 PWM(1) GPIO(50) BIDIR
|
|
PB6 TIM4_CH1 TIM4 PWM(2) GPIO(51)
|
|
PB1 TIM3_CH4 TIM3 PWM(3) GPIO(52) # UP shared with I2C2_RX, dshot not advised
|
|
PB0 TIM3_CH3 TIM3 PWM(4) GPIO(53) # UP shared with I2C2_RX, dshot not advised
|
|
PC9 TIM8_CH4 TIM8 PWM(5) GPIO(54) BIDIR
|
|
PC8 TIM8_CH3 TIM8 PWM(6) GPIO(55)
|
|
PB15 TIM1_CH3N TIM1 PWM(7) GPIO(56)
|
|
PB14 TIM1_CH2N TIM1 PWM(8) GPIO(57)
|
|
PA8 TIM1_CH1 TIM1 PWM(9) GPIO(58) BIDIR
|
|
PA15 TIM2_CH1 TIM2 PWM(10) GPIO(59) NODMA # no output
|
|
|
|
# Beeper
|
|
#PA7 TIM3_CH2 TIM3 GPIO(32) ALARM
|
|
|
|
# GPIOs
|
|
#PA4 PINIO1 OUTPUT GPIO(81) LOW
|
|
#PB5 PINIO2 OUTPUT GPIO(82) LOW
|
|
|
|
# --------------------- SPI1 -----------------------
|
|
PB3 SPI1_SCK SPI1
|
|
PB4 SPI1_MISO SPI1
|
|
PB5 SPI1_MOSI SPI1
|
|
|
|
PA4 IMU_CS CS
|
|
|
|
# --------------------- SPI2 -----------------------
|
|
PB13 SPI2_SCK SPI2
|
|
PC2 SPI2_MISO SPI2
|
|
PC3 SPI2_MOSI SPI2
|
|
|
|
PC4 OSD_CS CS
|
|
|
|
# -------------------- I2C bus --------------------
|
|
I2C_ORDER I2C1 I2C2
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
|
|
# --------------------- UARTs ---------------------------
|
|
SERIAL_ORDER OTG1 USART3 USART1 UART5 UART4 USART6 USART2
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# USART1 (labelled UART2 on casing)
|
|
PA9 USART1_TX USART1
|
|
PA10 USART1_RX USART1
|
|
|
|
# USART2 - RCIN with inverter / CRSF (4-pin RCIN connector)
|
|
PA2 USART2_TX USART2
|
|
PA3 TIM9_CH2 TIM9 RCININT PULLDOWN
|
|
|
|
# alternative with PA3 as USART2_RX
|
|
PA3 USART2_RX USART2 ALT(1)
|
|
define DEFAULT_SERIAL6_PROTOCOL SerialProtocol_RCIN
|
|
|
|
# USART3 - (labelled UART1 on casing)
|
|
PC10 USART3_TX USART3
|
|
PC11 USART3_RX USART3
|
|
|
|
# UART4 - (NC)
|
|
PA0 UART4_TX UART4 NODMA
|
|
PA1 UART4_RX UART4 NODMA
|
|
|
|
# UART5 - (GPS)
|
|
PC12 UART5_TX UART5
|
|
PD2 UART5_RX UART5 NODMA
|
|
|
|
# USART6 - (VTX)
|
|
PC6 USART6_TX USART6 NODMA
|
|
PC7 USART6_RX USART6 NODMA
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# ------------------- DMA assignment -------------------
|
|
DMA_PRIORITY ADC1 SPI1* SPI2* USART2*
|
|
|
|
# ------------------- IMU ICM42605 ---------------------
|
|
SPIDEV icm42688 SPI1 DEVID1 IMU_CS MODE3 1*MHZ 8*MHZ
|
|
IMU Invensensev3 SPI:icm42688 ROTATION_ROLL_180_YAW_90
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
|
|
|
|
|
# ------------------ OSD AT7456E ----------------------
|
|
SPIDEV osd SPI2 DEVID2 OSD_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
define OSD_ENABLED 1
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font0.bin
|
|
|
|
|
|
# ----------------- I2C compass & Baro -----------------
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
# external compass types
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
# built-in barometer
|
|
BARO SPL06 I2C:0:0x77
|
|
|
|
|
|
# --------------------- ADC ---------------------------
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
// RSSI_ADC_PIN ADC1 SCALE(1)
|
|
//PC0 PRESSURE_SENS ADC1 SCALE(1)
|
|
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
|
|
define HAL_BATT_VOLT_PIN 10
|
|
define HAL_BATT_VOLT_SCALE 7.71
|
|
|
|
define HAL_BATT_CURR_PIN 11
|
|
define HAL_BATT_CURR_SCALE 26.7
|
|
|
|
#define BOARD_RSSI_ANA_PIN 8
|
|
#define HAL_DEFAULT_AIRSPEED_PIN 10
|
|
|
|
define HAL_WITH_DSP FALSE
|
|
|
|
include ../include/minimize_fpv_osd.inc
|
|
|
|
AUTOBUILD_TARGETS Plane
|