mirror of https://github.com/ArduPilot/ardupilot
159 lines
3.8 KiB
Plaintext
159 lines
3.8 KiB
Plaintext
# hw definition file for SpeedyBee F4 v3 hardware
|
|
# tested on the Speedybee F4 v3 board
|
|
# with thanks to betaflight for pinout
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1082
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
define STM32_ST_USE_TIMER 5
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
# only one I2C bus
|
|
I2C_ORDER I2C2
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 UART5 USART6
|
|
|
|
# LEDs
|
|
PC8 LED_BLUE OUTPUT LOW GPIO(0)
|
|
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
|
|
# buzzer
|
|
PC5 BUZZER OUTPUT GPIO(80) LOW
|
|
define HAL_BUZZER_PIN 80
|
|
define HAL_BUZZER_ON 1
|
|
define HAL_BUZZER_OFF 0
|
|
|
|
# spi1 bus for IMU
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
PA4 BMI270_CS CS
|
|
|
|
# spi2 for OSD and sdcard
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
PB12 MAX7456_CS CS
|
|
PA15 SDCARD_CS CS
|
|
|
|
# only one I2C bus in normal config
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
|
|
# analog pins
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
PC2 RSSI_ADC_PIN ADC1 SCALE(1)
|
|
|
|
# define default battery setup
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
define HAL_BATT_VOLT_PIN 10
|
|
define HAL_BATT_CURR_PIN 11
|
|
define HAL_BATT_VOLT_SCALE 11.2 # matched to ESC output
|
|
define HAL_BATT_CURR_SCALE 52.7 # appropriate for a T-Motor F55A Pro II
|
|
|
|
# analog rssi pin
|
|
define BOARD_RSSI_ANA_PIN 12
|
|
|
|
# USART1 (DJI / VTX)
|
|
PA9 USART1_TX USART1
|
|
PA10 USART1_RX USART1
|
|
define HAL_SERIAL1_PROTOCOL SerialProtocol_DJI_FPV
|
|
|
|
# USART2 (RCIN)
|
|
PA2 USART2_TX USART2
|
|
PA3 USART2_RX USART2
|
|
define HAL_SERIAL2_PROTOCOL SerialProtocol_RCIN
|
|
|
|
# USART3 (CAM)
|
|
PC10 USART3_TX USART3 NODMA
|
|
PC11 USART3_RX USART3 NODMA
|
|
define HAL_SERIAL3_PROTOCOL SerialProtocol_None
|
|
|
|
# UART4 (Bluetooth)
|
|
PA0 UART4_TX UART4 NODMA
|
|
PA1 UART4_RX UART4 NODMA
|
|
define HAL_SERIAL4_PROTOCOL SerialProtocol_None
|
|
|
|
# UART5 (ESC Telemetry)
|
|
PC12 UART5_TX UART5 NODMA
|
|
PD2 UART5_RX UART5 NODMA
|
|
define HAL_SERIAL5_PROTOCOL SerialProtocol_ESCTelemetry
|
|
define HAL_SERIAL5_BAUD 19200
|
|
|
|
# UART6 (GPS)
|
|
PC6 USART6_TX USART6
|
|
PC7 USART6_RX USART6
|
|
define HAL_SERIAL6_PROTOCOL SerialProtocol_GPS
|
|
define HAL_SERIAL6_BAUD AP_SERIALMANAGER_GPS_BAUD
|
|
|
|
# PA10 IO-debug-console
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# PWM out pins. Note that channel order follows the ArduPilot motor
|
|
# order conventions
|
|
PB6 TIM4_CH1 TIM4 PWM(1) GPIO(50) BIDIR
|
|
PB7 TIM4_CH2 TIM4 PWM(2) GPIO(51)
|
|
PB8 TIM4_CH3 TIM4 PWM(3) GPIO(52) BIDIR # DMA channel shared with I2C2_TX, beware - no alternatives
|
|
PB9 TIM4_CH4 TIM4 PWM(4) GPIO(53)
|
|
PB0 TIM3_CH3 TIM3 PWM(5) GPIO(54)
|
|
PB1 TIM3_CH4 TIM3 PWM(6) GPIO(55)
|
|
PB5 TIM3_CH2 TIM3 PWM(7) GPIO(56)
|
|
PB4 TIM3_CH1 TIM3 PWM(8) GPIO(57)
|
|
PC9 TIM8_CH4 TIM8 PWM(9) GPIO(58) # LED
|
|
|
|
# OSD pad for TTL based OSD control, not supported by AP
|
|
PB3 CAM_C OUTPUT LOW GPIO(83) # labelled as "CC"
|
|
|
|
define HAL_STORAGE_SIZE 15360
|
|
STORAGE_FLASH_PAGE 1
|
|
|
|
# reserve 16k for bootloader and 32k for flash storage
|
|
FLASH_RESERVE_START_KB 48
|
|
|
|
# one IMU
|
|
IMU BMI270 SPI:bmi270 ROTATION_ROLL_180
|
|
|
|
# built-in barometer
|
|
BARO SPL06 I2C:0:0x76
|
|
define AP_BARO_BACKEND_DEFAULT_ENABLED 0
|
|
define AP_BARO_SPL06_ENABLED 1
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
# external compass types
|
|
define ALLOW_ARM_NO_COMPASS
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
# Motor order implies Betaflight/X for standard ESCs
|
|
define HAL_FRAME_TYPE_DEFAULT 12
|
|
|
|
# SPI devices
|
|
SPIDEV bmi270 SPI1 DEVID1 BMI270_CS MODE3 1*MHZ 8*MHZ
|
|
SPIDEV osd SPI2 DEVID1 MAX7456_CS MODE0 10*MHZ 10*MHZ
|
|
SPIDEV sdcard SPI2 DEVID2 SDCARD_CS MODE0 400*KHZ 25*MHZ
|
|
|
|
# filesystem setup on sdcard
|
|
define HAL_OS_FATFS_IO 1
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
# setup for OSD
|
|
define OSD_ENABLED 1
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
|
|
|
# minimal drivers to reduce flash usage
|
|
include ../include/minimal.inc
|
|
define AP_BATTMON_SYNTHETIC_CURRENT_ENABLED 0
|