ardupilot/libraries/AP_HAL_ChibiOS/hwdef/MambaF405-2022
Peter Barker 389eb3ac50 AP_HAL_ChibiOS: minimize Mamba405-2022 2023-01-03 11:39:18 +11:00
..
README.md AP_HAL_ChibiOS: add support for MambaF405 2022 MK4 2022-06-15 17:05:41 +10:00
basic20pinout.png AP_HAL_ChibiOS: add support for MambaF405 2022 MK4 2022-06-15 17:05:41 +10:00
hwdef-bl.dat AP_HAL_ChibiOS: add support for MambaF405 2022 MK4 2022-06-15 17:05:41 +10:00
hwdef.dat AP_HAL_ChibiOS: minimize Mamba405-2022 2023-01-03 11:39:18 +11:00

README.md

Mamba Basic F405 MK4 Flight Controller

The Mamba Basic line of flight controllers are produced by Diatone.

Features

  • STM32F405RGT6 microcontroller
  • MPU6000 IMU
  • AT7456E OSD
  • 4 UARTs
  • 7 PWM outputs (6 Motor Output, 1 LED)

Pinout

Mamba Basic 20x20 Pinout

UART Mapping

The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the receive pin for UARTn. The Tn pin is the transmit pin for UARTn.

Name Pin Function
SERIAL0 COMPUTER USB
SERIAL1 PPM/RX1/SBUS/TX1 UART1 (RC Input)
SERIAL2 TX2/RX2 UART2 (DMA-enabled)
SERIAL3 TX3/RX3 UART3 (Telem1)
SERIAL4 TX4/RX4 UART4 (Empty)
SERIAL6 TX6/RX6 UART6 (GPS, DMA-enabled)

RC Input

RC input is configured on the PPM (UART1_RX) pin. It supports all RC protocols.

OSD Support

The Mamba F405 MK4 supports OSD using OSD_TYPE 1 (MAX7456 driver).

PWM Output

The Mamba F405 MK4 supports up to 7 PWM outputs. The pads for motor output ESC1 to ESC4 on the above diagram are for the 4 outputs. All outputs support DShot as well as all PWM types. Motors 1-4 support bi-directional DShot.

The PWM is in 4 groups:

  • PWM 1,2 in group1
  • PWM 3,4 in group2
  • PWM 5,6 in group3
  • PWM 7 in group4

Channels within the same group need to use the same output rate. If any channel in a group uses DShot then all channels in the group need to use DShot.

Battery Monitoring

The board has a builting voltage sensor. The voltage sensor can handle up to 6S LiPo batteries.

The correct battery setting parameters are:

  • BATT_MONITOR 3
  • BATT_VOLT_PIN 11
  • BATT_VOLT_MULT around 11.0
  • BATT_CURR_PIN 13
  • BATT_CURR_MULT around 28 with the 20x20 40A ESC (calculated, needs to be verified)

Compass

The Mamba Basic flight controllers do not have a builtin compass, but you can attach an external compass using I2C on the SDA and SCL pads.

Alternate settings

It is possible to set alternate configurations with the BRD_ALT_CONFIG parameter.

BRD_ALT_CONFIG RX1 function
ALT 0(default) RCININT
ALT 1 RX1/TX1

Loading Firmware

Initial firmware load can be done with DFU by plugging in USB with the bootloader button pressed. Then you should load the "with_bl.hex" firmware, using your favourite DFU loading tool.

Once the initial firmware is loaded you can update the firmware using any ArduPilot ground station software. Updates should be done with the *.apj firmware files.