ardupilot/ArduCopterMega/HIL.h

128 lines
3.3 KiB
C++

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: t -*-
/// @file HIL.h
/// @brief Interface definition for the various Ground Control System protocols.
#ifndef __HIL_H
#define __HIL_H
# if HIL_MODE != HIL_MODE_DISABLED
#include <BetterStream.h>
#include <AP_Common.h>
#include <GPS.h>
#include <Stream.h>
#include <stdint.h>
///
/// @class HIL
/// @brief Class describing the interface between the APM code
/// proper and the HIL implementation.
///
/// HIL' are currently implemented inside the sketch and as such have
/// access to all global state. The sketch should not, however, call HIL
/// internal functions - all calls to the HIL should be routed through
/// this interface (or functions explicitly exposed by a subclass).
///
class HIL_Class
{
public:
/// Startup initialisation.
///
/// This routine performs any one-off initialisation required before
/// HIL messages are exchanged.
///
/// @note The stream is expected to be set up and configured for the
/// correct bitrate before ::init is called.
///
/// @note The stream is currently BetterStream so that we can use the _P
/// methods; this may change if Arduino adds them to Print.
///
/// @param port The stream over which messages are exchanged.
///
void init(BetterStream *port) { _port = port; }
/// Update HIL state.
///
/// This may involve checking for received bytes on the stream,
/// or sending additional periodic messages.
void update(void) {}
/// Send a message with a single numeric parameter.
///
/// This may be a standalone message, or the HIL driver may
/// have its own way of locating additional parameters to send.
///
/// @param id ID of the message to send.
/// @param param Explicit message parameter.
///
void send_message(uint8_t id, int32_t param = 0) {}
/// Send a text message.
///
/// @param severity A value describing the importance of the message.
/// @param str The text to be sent.
///
void send_text(uint8_t severity, const char *str) {}
/// Send acknowledgement for a message.
///
/// @param id The message ID being acknowledged.
/// @param sum1 Checksum byte 1 from the message being acked.
/// @param sum2 Checksum byte 2 from the message being acked.
///
void acknowledge(uint8_t id, uint8_t sum1, uint8_t sum2) {}
protected:
/// The stream we are communicating over
BetterStream *_port;
};
//
// HIL class definitions.
//
// These are here so that we can declare the HIL object early in the sketch
// and then reference it statically rather than via a pointer.
//
///
/// @class HIL_MAVLINK
/// @brief The mavlink protocol for hil
///
#if HIL_PROTOCOL == HIL_PROTOCOL_MAVLINK
// uses gcs
#endif // HIL_PROTOCOL_MAVLINK
///
/// @class HIL_XPLANE
/// @brief The xplane protocol for hil
///
#if HIL_PROTOCOL == HIL_PROTOCOL_XPLANE
class HIL_XPLANE : public HIL_Class
{
public:
HIL_XPLANE();
void update(void);
void init(BetterStream *port);
void send_message(uint8_t id, uint32_t param = 0);
void send_text(uint8_t severity, const char *str);
void acknowledge(uint8_t id, uint8_t sum1, uint8_t sum2);
private:
void output_HIL();
void output_HIL_();
void output_int(int value);
void output_byte(byte value);
void print_buffer();
AP_GPS_IMU * hilPacketDecoder;
byte buf_len;
byte out_buffer[32];
};
#endif // HIL_PROTOCOL_XPLANE
#endif // HIL not disabled
#endif // __HIL_H