mirror of https://github.com/ArduPilot/ardupilot
133 lines
3.8 KiB
C++
133 lines
3.8 KiB
C++
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
#include "Rover.h"
|
|
|
|
/*
|
|
allow for runtime change of control channel ordering
|
|
*/
|
|
void Rover::set_control_channels(void)
|
|
{
|
|
channel_steer = RC_Channel::rc_channel(rcmap.roll()-1);
|
|
channel_throttle = RC_Channel::rc_channel(rcmap.throttle()-1);
|
|
channel_learn = RC_Channel::rc_channel(g.learn_channel-1);
|
|
|
|
// set rc channel ranges
|
|
channel_steer->set_angle(SERVO_MAX);
|
|
channel_throttle->set_angle(100);
|
|
|
|
// setup correct scaling for ESCs like the UAVCAN PX4ESC which
|
|
// take a proportion of speed.
|
|
hal.rcout->set_esc_scaling(channel_throttle->radio_min, channel_throttle->radio_max);
|
|
}
|
|
|
|
void Rover::init_rc_in()
|
|
{
|
|
// set rc dead zones
|
|
channel_steer->set_default_dead_zone(30);
|
|
channel_throttle->set_default_dead_zone(30);
|
|
|
|
//set auxiliary ranges
|
|
update_aux();
|
|
}
|
|
|
|
void Rover::init_rc_out()
|
|
{
|
|
RC_Channel::rc_channel(CH_1)->enable_out();
|
|
RC_Channel::rc_channel(CH_3)->enable_out();
|
|
RC_Channel::output_trim_all();
|
|
|
|
// setup PWM values to send if the FMU firmware dies
|
|
RC_Channel::setup_failsafe_trim_all();
|
|
}
|
|
|
|
void Rover::read_radio()
|
|
{
|
|
if (!hal.rcin->new_input()) {
|
|
control_failsafe(channel_throttle->radio_in);
|
|
return;
|
|
}
|
|
|
|
failsafe.last_valid_rc_ms = hal.scheduler->millis();
|
|
|
|
RC_Channel::set_pwm_all();
|
|
|
|
control_failsafe(channel_throttle->radio_in);
|
|
|
|
channel_throttle->servo_out = channel_throttle->control_in;
|
|
|
|
if (abs(channel_throttle->servo_out) > 50) {
|
|
throttle_nudge = (g.throttle_max - g.throttle_cruise) * ((fabsf(channel_throttle->norm_input())-0.5f) / 0.5f);
|
|
} else {
|
|
throttle_nudge = 0;
|
|
}
|
|
|
|
if (g.skid_steer_in) {
|
|
// convert the two radio_in values from skid steering values
|
|
/*
|
|
mixing rule:
|
|
steering = motor1 - motor2
|
|
throttle = 0.5*(motor1 + motor2)
|
|
motor1 = throttle + 0.5*steering
|
|
motor2 = throttle - 0.5*steering
|
|
*/
|
|
|
|
float motor1 = channel_steer->norm_input();
|
|
float motor2 = channel_throttle->norm_input();
|
|
float steering_scaled = motor1 - motor2;
|
|
float throttle_scaled = 0.5f*(motor1 + motor2);
|
|
int16_t steer = channel_steer->radio_trim;
|
|
int16_t thr = channel_throttle->radio_trim;
|
|
if (steering_scaled > 0.0f) {
|
|
steer += steering_scaled*(channel_steer->radio_max-channel_steer->radio_trim);
|
|
} else {
|
|
steer += steering_scaled*(channel_steer->radio_trim-channel_steer->radio_min);
|
|
}
|
|
if (throttle_scaled > 0.0f) {
|
|
thr += throttle_scaled*(channel_throttle->radio_max-channel_throttle->radio_trim);
|
|
} else {
|
|
thr += throttle_scaled*(channel_throttle->radio_trim-channel_throttle->radio_min);
|
|
}
|
|
channel_steer->set_pwm(steer);
|
|
channel_throttle->set_pwm(thr);
|
|
}
|
|
}
|
|
|
|
void Rover::control_failsafe(uint16_t pwm)
|
|
{
|
|
if (!g.fs_throttle_enabled) {
|
|
// no throttle failsafe
|
|
return;
|
|
}
|
|
|
|
// Check for failsafe condition based on loss of GCS control
|
|
if (rc_override_active) {
|
|
failsafe_trigger(FAILSAFE_EVENT_RC, (millis() - failsafe.rc_override_timer) > 1500);
|
|
} else if (g.fs_throttle_enabled) {
|
|
bool failed = pwm < (uint16_t)g.fs_throttle_value;
|
|
if (hal.scheduler->millis() - failsafe.last_valid_rc_ms > 2000) {
|
|
failed = true;
|
|
}
|
|
failsafe_trigger(FAILSAFE_EVENT_THROTTLE, failed);
|
|
}
|
|
}
|
|
|
|
void Rover::trim_control_surfaces()
|
|
{
|
|
read_radio();
|
|
// Store control surface trim values
|
|
// ---------------------------------
|
|
if (channel_steer->radio_in > 1400) {
|
|
channel_steer->radio_trim = channel_steer->radio_in;
|
|
// save to eeprom
|
|
channel_steer->save_eeprom();
|
|
}
|
|
}
|
|
|
|
void Rover::trim_radio()
|
|
{
|
|
for (int y = 0; y < 30; y++) {
|
|
read_radio();
|
|
}
|
|
trim_control_surfaces();
|
|
}
|