mirror of https://github.com/ArduPilot/ardupilot
289 lines
14 KiB
C++
289 lines
14 KiB
C++
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
/// @file AP_MotorsHeli.h
|
|
/// @brief Motor control class for Traditional Heli
|
|
|
|
#ifndef __AP_MOTORS_HELI_H__
|
|
#define __AP_MOTORS_HELI_H__
|
|
|
|
#include <inttypes.h>
|
|
#include <AP_Common.h>
|
|
#include <AP_Math.h> // ArduPilot Mega Vector/Matrix math Library
|
|
#include <RC_Channel.h> // RC Channel Library
|
|
#include "AP_Motors.h"
|
|
|
|
// maximum number of swashplate servos
|
|
#define AP_MOTORS_HELI_NUM_SWASHPLATE_SERVOS 3
|
|
|
|
// servo output rates
|
|
#define AP_MOTORS_HELI_SPEED_DEFAULT 125 // default servo update rate for helicopters
|
|
#define AP_MOTORS_HELI_SPEED_DIGITAL_SERVOS 125 // update rate for digital servos
|
|
#define AP_MOTORS_HELI_SPEED_ANALOG_SERVOS 125 // update rate for analog servos
|
|
|
|
// TradHeli Aux Function Output Channels
|
|
#define AP_MOTORS_HELI_AUX CH_7
|
|
#define AP_MOTORS_HELI_RSC CH_8
|
|
|
|
// servo position defaults
|
|
#define AP_MOTORS_HELI_SERVO1_POS -60
|
|
#define AP_MOTORS_HELI_SERVO2_POS 60
|
|
#define AP_MOTORS_HELI_SERVO3_POS 180
|
|
|
|
// swash type definitions
|
|
#define AP_MOTORS_HELI_SWASH_CCPM 0
|
|
#define AP_MOTORS_HELI_SWASH_H1 1
|
|
|
|
// default swash min and max angles and positions
|
|
#define AP_MOTORS_HELI_SWASH_ROLL_MAX 2500
|
|
#define AP_MOTORS_HELI_SWASH_PITCH_MAX 2500
|
|
#define AP_MOTORS_HELI_COLLECTIVE_MIN 1250
|
|
#define AP_MOTORS_HELI_COLLECTIVE_MAX 1750
|
|
#define AP_MOTORS_HELI_COLLECTIVE_MID 1500
|
|
|
|
// swash min and max position while in stabilize mode (as a number from 0 ~ 100)
|
|
#define AP_MOTORS_HELI_MANUAL_COLLECTIVE_MIN 0
|
|
#define AP_MOTORS_HELI_MANUAL_COLLECTIVE_MAX 100
|
|
|
|
// swash min while landed or landing (as a number from 0 ~ 1000
|
|
#define AP_MOTORS_HELI_LAND_COLLECTIVE_MIN 0
|
|
|
|
// tail types
|
|
#define AP_MOTORS_HELI_TAILTYPE_SERVO 0
|
|
#define AP_MOTORS_HELI_TAILTYPE_SERVO_EXTGYRO 1
|
|
#define AP_MOTORS_HELI_TAILTYPE_DIRECTDRIVE_VARPITCH 2
|
|
#define AP_MOTORS_HELI_TAILTYPE_DIRECTDRIVE_FIXEDPITCH 3
|
|
|
|
// default external gyro gain (ch7 out)
|
|
#define AP_MOTORS_HELI_EXT_GYRO_GAIN 350
|
|
|
|
// minimum outputs for direct drive motors
|
|
#define AP_MOTOR_HELI_DDTAIL_DEFAULT 500
|
|
|
|
|
|
// main rotor speed control types (ch8 out)
|
|
#define AP_MOTORS_HELI_RSC_MODE_NONE 0 // main rotor ESC is directly connected to receiver, pilot controls ESC speed through transmitter directly
|
|
#define AP_MOTORS_HELI_RSC_MODE_CH8_PASSTHROUGH 1 // main rotor ESC is connected to RC8 (out), pilot desired rotor speed provided by CH8 input
|
|
#define AP_MOTORS_HELI_RSC_MODE_SETPOINT 2 // main rotor ESC is connected to RC8 (out), desired speed is held in RSC_SETPOINT parameter
|
|
|
|
// default main rotor speed (ch8 out) as a number from 0 ~ 1000
|
|
#define AP_MOTORS_HELI_RSC_SETPOINT 500
|
|
|
|
// default main rotor ramp up time in seconds
|
|
#define AP_MOTORS_HELI_RSC_RAMP_TIME 1 // 1 second to ramp output to main rotor ESC to full power (most people use exterrnal govenors so we can ramp up quickly)
|
|
#define AP_MOTORS_HELI_RSC_RUNUP_TIME 10 // 10 seconds for rotor to reach full speed
|
|
#define AP_MOTORS_HELI_TAIL_RAMP_INCREMENT 5 // 5 is 2 seconds for direct drive tail rotor to reach to full speed (5 = (2sec*100hz)/1000)
|
|
|
|
// motor run-up time default in 100th of seconds
|
|
#define AP_MOTORS_HELI_MOTOR_RUNUP_TIME 500 // 500 = 5 seconds
|
|
|
|
// flybar types
|
|
#define AP_MOTORS_HELI_NOFLYBAR 0
|
|
#define AP_MOTORS_HELI_FLYBAR 1
|
|
|
|
class AP_HeliControls;
|
|
|
|
/// @class AP_MotorsHeli
|
|
class AP_MotorsHeli : public AP_Motors {
|
|
public:
|
|
|
|
/// Constructor
|
|
AP_MotorsHeli( RC_Channel& rc_roll,
|
|
RC_Channel& rc_pitch,
|
|
RC_Channel& rc_throttle,
|
|
RC_Channel& rc_yaw,
|
|
RC_Channel& servo_aux,
|
|
RC_Channel& servo_rotor,
|
|
RC_Channel& swash_servo_1,
|
|
RC_Channel& swash_servo_2,
|
|
RC_Channel& swash_servo_3,
|
|
RC_Channel& yaw_servo,
|
|
uint16_t speed_hz = AP_MOTORS_HELI_SPEED_DEFAULT) :
|
|
AP_Motors(rc_roll, rc_pitch, rc_throttle, rc_yaw, speed_hz),
|
|
_servo_aux(servo_aux),
|
|
_servo_rsc(servo_rotor),
|
|
_servo_1(swash_servo_1),
|
|
_servo_2(swash_servo_2),
|
|
_servo_3(swash_servo_3),
|
|
_servo_4(yaw_servo),
|
|
_roll_scaler(1),
|
|
_pitch_scaler(1),
|
|
_collective_scalar(1),
|
|
_collective_out(0),
|
|
_collective_mid_pwm(0),
|
|
_rotor_desired(0),
|
|
_rotor_out(0),
|
|
_rsc_ramp_increment(0.0f),
|
|
_rsc_runup_increment(0.0f),
|
|
_rotor_speed_estimate(0.0f),
|
|
_tail_direct_drive_out(0)
|
|
{
|
|
AP_Param::setup_object_defaults(this, var_info);
|
|
|
|
// initialise flags
|
|
_heliflags.swash_initialised = 0;
|
|
_heliflags.landing_collective = 0;
|
|
_heliflags.motor_runup_complete = 0;
|
|
};
|
|
|
|
// init
|
|
void Init();
|
|
|
|
// set update rate to motors - a value in hertz
|
|
// you must have setup_motors before calling this
|
|
void set_update_rate( uint16_t speed_hz );
|
|
|
|
// enable - starts allowing signals to be sent to motors
|
|
void enable();
|
|
|
|
// output_min - sends minimum values out to the motors
|
|
void output_min();
|
|
|
|
// output_test - spin a motor at the pwm value specified
|
|
// motor_seq is the motor's sequence number from 1 to the number of motors on the frame
|
|
// pwm value is an actual pwm value that will be output, normally in the range of 1000 ~ 2000
|
|
virtual void output_test(uint8_t motor_seq, int16_t pwm);
|
|
|
|
//
|
|
// heli specific methods
|
|
//
|
|
|
|
// allow_arming - returns true if main rotor is spinning and it is ok to arm
|
|
bool allow_arming() const;
|
|
|
|
// _tail_type - returns the tail type (servo, servo with ext gyro, direct drive var pitch, direct drive fixed pitch)
|
|
int16_t tail_type() const { return _tail_type; }
|
|
|
|
// ext_gyro_gain - gets and sets external gyro gain as a pwm (1000~2000)
|
|
int16_t ext_gyro_gain() const { return _ext_gyro_gain; }
|
|
void ext_gyro_gain(int16_t pwm) { _ext_gyro_gain = pwm; }
|
|
|
|
// has_flybar - returns true if we have a mechical flybar
|
|
bool has_flybar() const { return _flybar_mode; }
|
|
|
|
// get_collective_mid - returns collective mid position as a number from 0 ~ 1000
|
|
int16_t get_collective_mid() const { return _collective_mid; }
|
|
|
|
// get_collective_out - returns collective position from last output as a number from 0 ~ 1000
|
|
int16_t get_collective_out() const { return _collective_out; }
|
|
|
|
// set_collective_for_landing - limits collective from going too low if we know we are landed
|
|
void set_collective_for_landing(bool landing) { _heliflags.landing_collective = landing; }
|
|
|
|
// get_rsc_mode - gets the rotor speed control method (AP_MOTORS_HELI_RSC_MODE_NONE, AP_MOTORS_HELI_RSC_MODE_CH8_PASSTHROUGH or AP_MOTORS_HELI_RSC_MODE_SETPOINT)
|
|
uint8_t get_rsc_mode() const { return _rsc_mode; }
|
|
|
|
// get_rsc_setpoint - gets contents of _rsc_setpoint parameter (0~1000)
|
|
int16_t get_rsc_setpoint() const { return _rsc_setpoint; }
|
|
|
|
// set_desired_rotor_speed - sets target rotor speed as a number from 0 ~ 1000
|
|
void set_desired_rotor_speed(int16_t desired_speed);
|
|
|
|
// return true if the main rotor is up to speed
|
|
bool motor_runup_complete() const;
|
|
|
|
// recalc_scalers - recalculates various scalers used. Should be called at about 1hz to allow users to see effect of changing parameters
|
|
void recalc_scalers();
|
|
|
|
// get_phase_angle - returns phase angle
|
|
int16_t get_phase_angle() const { return _phase_angle; }
|
|
|
|
// var_info for holding Parameter information
|
|
static const struct AP_Param::GroupInfo var_info[];
|
|
|
|
protected:
|
|
|
|
// output - sends commands to the motors
|
|
void output_armed();
|
|
void output_disarmed();
|
|
|
|
private:
|
|
|
|
// heli_move_swash - moves swash plate to attitude of parameters passed in
|
|
void move_swash(int16_t roll_out, int16_t pitch_out, int16_t coll_in, int16_t yaw_out);
|
|
|
|
// reset_swash - free up swash for maximum movements. Used for set-up
|
|
void reset_swash();
|
|
|
|
// init_swash - initialise the swash plate
|
|
void init_swash();
|
|
|
|
// calculate_roll_pitch_collective_factors - calculate factors based on swash type and servo position
|
|
void calculate_roll_pitch_collective_factors();
|
|
|
|
// rsc_control - main function to update values to send to main rotor and tail rotor ESCs
|
|
void rsc_control();
|
|
|
|
// rotor_ramp - ramps rotor towards target. result put rotor_out and sent to ESC
|
|
void rotor_ramp(int16_t rotor_target);
|
|
|
|
// tail_ramp - ramps tail motor towards target. Only used for direct drive variable pitch tails
|
|
// results put into _tail_direct_drive_out and sent to ESC
|
|
void tail_ramp(int16_t tail_target);
|
|
|
|
// return true if the tail rotor is up to speed
|
|
bool tail_rotor_runup_complete();
|
|
|
|
// write_rsc - outputs pwm onto output rsc channel (ch8). servo_out parameter is of the range 0 ~ 1000
|
|
void write_rsc(int16_t servo_out);
|
|
|
|
// write_aux - outputs pwm onto output aux channel (ch7). servo_out parameter is of the range 0 ~ 1000
|
|
void write_aux(int16_t servo_out);
|
|
|
|
// external objects we depend upon
|
|
RC_Channel& _servo_aux; // output to ext gyro gain and tail direct drive esc (ch7)
|
|
RC_Channel& _servo_rsc; // output to main rotor esc (ch8)
|
|
RC_Channel& _servo_1; // swash plate servo #1
|
|
RC_Channel& _servo_2; // swash plate servo #2
|
|
RC_Channel& _servo_3; // swash plate servo #3
|
|
RC_Channel& _servo_4; // tail servo
|
|
|
|
// flags bitmask
|
|
struct heliflags_type {
|
|
uint8_t swash_initialised : 1; // true if swash has been initialised
|
|
uint8_t landing_collective : 1; // true if collective is setup for landing which has much higher minimum
|
|
uint8_t motor_runup_complete : 1; // true if the rotors have had enough time to wind up
|
|
} _heliflags;
|
|
|
|
// parameters
|
|
AP_Int16 _servo1_pos; // Angular location of swash servo #1
|
|
AP_Int16 _servo2_pos; // Angular location of swash servo #2
|
|
AP_Int16 _servo3_pos; // Angular location of swash servo #3
|
|
AP_Int16 _roll_max; // Maximum roll angle of the swash plate in centi-degrees
|
|
AP_Int16 _pitch_max; // Maximum pitch angle of the swash plate in centi-degrees
|
|
AP_Int16 _collective_min; // Lowest possible servo position for the swashplate
|
|
AP_Int16 _collective_max; // Highest possible servo position for the swashplate
|
|
AP_Int16 _collective_mid; // Swash servo position corresponding to zero collective pitch (or zero lift for Assymetrical blades)
|
|
AP_Int16 _tail_type; // Tail type used: Servo, Servo with external gyro, direct drive variable pitch or direct drive fixed pitch
|
|
AP_Int8 _swash_type; // Swash Type Setting - either 3-servo CCPM or H1 Mechanical Mixing
|
|
AP_Int16 _ext_gyro_gain; // PWM sent to external gyro on ch7 when tail type is Servo w/ ExtGyro
|
|
AP_Int8 _servo_manual; // Pass radio inputs directly to servos during set-up through mission planner
|
|
AP_Int16 _phase_angle; // Phase angle correction for rotor head. If pitching the swash forward induces a roll, this can be correct the problem
|
|
AP_Int16 _collective_yaw_effect; // Feed-forward compensation to automatically add rudder input when collective pitch is increased. Can be positive or negative depending on mechanics.
|
|
AP_Int16 _rsc_setpoint; // rotor speed when RSC mode is set to is enabledv
|
|
AP_Int8 _rsc_mode; // Which main rotor ESC control mode is active
|
|
AP_Int8 _rsc_ramp_time; // Time in seconds for the output to the main rotor's ESC to reach full speed
|
|
AP_Int8 _rsc_runup_time; // Time in seconds for the main rotor to reach full speed. Must be longer than _rsc_ramp_time
|
|
AP_Int8 _flybar_mode; // Flybar present or not. Affects attitude controller used during ACRO flight mode
|
|
AP_Int16 _land_collective_min; // Minimum collective when landed or landing
|
|
AP_Int16 _direct_drive_tailspeed; // Direct Drive VarPitch Tail ESC speed (0 ~ 1000)
|
|
|
|
// internal variables
|
|
float _rollFactor[AP_MOTORS_HELI_NUM_SWASHPLATE_SERVOS];
|
|
float _pitchFactor[AP_MOTORS_HELI_NUM_SWASHPLATE_SERVOS];
|
|
float _collectiveFactor[AP_MOTORS_HELI_NUM_SWASHPLATE_SERVOS];
|
|
float _roll_scaler; // scaler to convert roll input from radio (i.e. -4500 ~ 4500) to max roll range
|
|
float _pitch_scaler; // scaler to convert pitch input from radio (i.e. -4500 ~ 4500) to max pitch range
|
|
float _collective_scalar; // collective scalar to convert pwm form (i.e. 0 ~ 1000) passed in to actual servo range (i.e 1250~1750 would be 500)
|
|
float _collective_scalar_manual; // collective scalar to reduce the range of the collective movement while collective is being controlled manually (i.e. directly by the pilot)
|
|
int16_t _collective_out; // actual collective pitch value. Required by the main code for calculating cruise throttle
|
|
int16_t _collective_mid_pwm; // collective mid parameter value converted to pwm form (i.e. 0 ~ 1000)
|
|
int16_t _rotor_desired; // latest desired rotor speed from pilot
|
|
float _rotor_out; // latest output sent to the main rotor or an estimate of the rotors actual speed (whichever is higher) (0 ~ 1000)
|
|
float _rsc_ramp_increment; // the amount we can increase the rotor output during each 100hz iteration
|
|
float _rsc_runup_increment; // the amount we can increase the rotor's estimated speed during each 100hz iteration
|
|
float _rotor_speed_estimate; // estimated speed of the main rotor (0~1000)
|
|
int16_t _tail_direct_drive_out; // current ramped speed of output on ch7 when using direct drive variable pitch tail type
|
|
};
|
|
|
|
#endif // AP_MOTORSHELI
|