mirror of https://github.com/ArduPilot/ardupilot
82 lines
2.5 KiB
Plaintext
82 lines
2.5 KiB
Plaintext
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
// Sensors are not available in HIL_MODE_ATTITUDE
|
|
#if HIL_MODE != HIL_MODE_ATTITUDE
|
|
|
|
void ReadSCP1000(void) {}
|
|
|
|
static void init_barometer(void)
|
|
{
|
|
barometer.calibrate(mavlink_delay);
|
|
ahrs.set_barometer(&barometer);
|
|
gcs_send_text_P(SEVERITY_LOW, PSTR("barometer calibration complete"));
|
|
}
|
|
|
|
// filter altitude from the barometer with a 0.3 low pass
|
|
// filter
|
|
static LowPassFilterInt32 altitude_filter(0.3);
|
|
|
|
// read the barometer and return the updated altitude in centimeters
|
|
// above the calibration altitude
|
|
static int32_t read_barometer(void)
|
|
{
|
|
barometer.read();
|
|
return altitude_filter.apply(((int32_t)barometer.get_altitude() * 100.0));
|
|
}
|
|
|
|
// in M/S * 100
|
|
static void read_airspeed(void)
|
|
{
|
|
#if GPS_PROTOCOL != GPS_PROTOCOL_IMU // Xplane will supply the airspeed
|
|
if (g.airspeed_offset == 0) {
|
|
// runtime enabling of airspeed, we need to do instant
|
|
// calibration before we can use it. This isn't as
|
|
// accurate as the 50 point average in zero_airspeed(),
|
|
// but it is better than using it uncalibrated
|
|
airspeed_raw = pitot_analog_source.read();
|
|
g.airspeed_offset.set_and_save(airspeed_raw);
|
|
}
|
|
airspeed_raw = (pitot_analog_source.read() * 0.1) + (airspeed_raw * 0.9);
|
|
airspeed_pressure = max((airspeed_raw - g.airspeed_offset), 0);
|
|
airspeed = sqrt(airspeed_pressure * g.airspeed_ratio) * 100;
|
|
#endif
|
|
|
|
calc_airspeed_errors();
|
|
}
|
|
|
|
static void zero_airspeed(void)
|
|
{
|
|
float sum = 0;
|
|
int c;
|
|
airspeed_raw = pitot_analog_source.read();
|
|
for(c = 0; c < 250; c++) {
|
|
delay(2);
|
|
sum += pitot_analog_source.read();
|
|
}
|
|
sum /= c;
|
|
g.airspeed_offset.set_and_save((int16_t)sum);
|
|
}
|
|
|
|
#endif // HIL_MODE != HIL_MODE_ATTITUDE
|
|
|
|
static void read_battery(void)
|
|
{
|
|
if(g.battery_monitoring == 0) {
|
|
battery_voltage1 = 0;
|
|
return;
|
|
}
|
|
|
|
if(g.battery_monitoring == 3 || g.battery_monitoring == 4)
|
|
battery_voltage1 = BATTERY_VOLTAGE(analogRead(BATTERY_PIN_1)) * .1 + battery_voltage1 * .9;
|
|
if(g.battery_monitoring == 4) {
|
|
current_amps1 = CURRENT_AMPS(analogRead(CURRENT_PIN_1)) * .1 + current_amps1 * .9; //reads power sensor current pin
|
|
current_total1 += current_amps1 * (float)delta_ms_medium_loop * 0.0002778; // .0002778 is 1/3600 (conversion to hours)
|
|
}
|
|
|
|
#if BATTERY_EVENT == ENABLED
|
|
if(battery_voltage1 < LOW_VOLTAGE) low_battery_event();
|
|
if(g.battery_monitoring == 4 && current_total1 > g.pack_capacity) low_battery_event();
|
|
#endif
|
|
}
|
|
|