ardupilot/ArduPlane
Andrew Tridgell 0d3faeda90 Plane: update_mount assumes 50Hz, for camera trigger 2013-06-25 12:44:26 +10:00
..
APM_Config.h Plane: removed HIL_MODE_ATTITUDE 2013-04-12 17:44:40 +10:00
APM_Config.h.reference Plane: updates for new compass API 2013-05-02 12:48:14 +10:00
ArduPlane.pde Plane: update_mount assumes 50Hz, for camera trigger 2013-06-25 12:44:26 +10:00
Attitude.pde Plane: APM2 doesn't have channel 9 PWM output 2013-06-24 13:06:54 +10:00
GCS.h Plane: switch to an array for stream rates 2013-02-05 08:20:41 +11:00
GCS_Mavlink.pde Plane: switch to new AP_Scheduler 2013-06-04 13:34:58 +10:00
Log.pde Plane: switch to new AP_Scheduler 2013-06-04 13:34:58 +10:00
Makefile Plane: use new apm.mk 2013-01-02 17:28:21 +11:00
Parameters.h Plane: enabled RELAY_* parameters 2013-06-25 12:44:26 +10:00
Parameters.pde Plane: enabled RELAY_* parameters 2013-06-25 12:44:26 +10:00
climb_rate.pde uncrustify ArduPlane/climb_rate.pde 2012-08-21 18:57:21 -07:00
command_description.txt Cleanup: rename files with spaces in their names, replace with underscores 2012-02-28 16:14:31 -08:00
commands.pde Plane: set loiter.direction for GUIDED mode 2013-04-21 23:46:35 +10:00
commands_logic.pde Plane: use RC_Channel::rc_channel() instead of rc_ch[] 2013-06-03 16:23:48 +10:00
commands_process.pde Plane: switch to new AP_Scheduler 2013-06-04 13:34:58 +10:00
compat.h ArduPlane: Ported to AP_HAL 2012-12-20 14:51:36 +11:00
compat.pde ArduPlane: Ported to AP_HAL 2012-12-20 14:51:36 +11:00
config.h Plane: use the new airspeed driver interface 2013-06-03 11:51:09 +10:00
control_modes.pde Plane: ignore control mode changes when in throttle failsafe 2013-02-21 11:21:39 +11:00
createTags imported ArduPlane from ArduPilotMega svn 2011-09-09 11:29:39 +10:00
defines.h Plane: fixed remaining places where primary channel ordering was assumed 2013-06-03 16:23:48 +10:00
events.pde Plane: make voltage and battery capacity failsafe settable at runtime 2013-05-22 20:33:57 +10:00
failsafe.pde Plane: fixed remaining places where primary channel ordering was assumed 2013-06-03 16:23:48 +10:00
geofence.pde Plane: use hal.storage for eeprom access 2012-12-20 14:51:39 +11:00
navigation.pde Plane: switch to new AP_Scheduler 2013-06-04 13:34:58 +10:00
nocore.inoflag ArduPlane: Ported to AP_HAL 2012-12-20 14:51:36 +11:00
radio.pde Plane: APM2 doesn't have channel 9 PWM output 2013-06-24 13:06:54 +10:00
sensors.pde Plane: switch to new AP_Scheduler 2013-06-04 13:34:58 +10:00
setup.pde Plane: allow channel mapping of first 4 channels 2013-06-03 16:23:48 +10:00
system.pde Plane: make GPS UART blocking again 2013-06-11 18:50:23 +10:00
test.pde Plane: switch to new AP_Scheduler 2013-06-04 13:34:58 +10:00