ardupilot/libraries/AP_HAL_ChibiOS/hwdef/CUAV-X7/hwdef.dat

307 lines
7.1 KiB
Plaintext

# hw definition file for processing by chibios_hwdef.py for CUAV-X7
# MCU class and specific type
MCU STM32H7xx STM32H743xx
# crystal frequency
OSCILLATOR_HZ 16000000
# board ID for firmware load
APJ_BOARD_ID 1010
FLASH_SIZE_KB 2048
# with 2M flash we can afford to optimize for speed
env OPTIMIZE -O2
# ChibiOS system timer
STM32_ST_USE_TIMER 2
# bootloader takes first sector
FLASH_RESERVE_START_KB 128
# order of UARTs (and USB)
SERIAL_ORDER OTG1 USART2 USART6 USART1 UART4 UART8 UART7 OTG2
# default the 2nd interface to MAVLink2 until MissionPlanner updates drivers
define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2
# now we define the pins that USB is connected on
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
# Port switching for USB HS and FS,high = USB_FS , LOW = USB_HS
PH15 USB_HS_ENABLE OUTPUT HIGH
define USB_HW_ENABLE_HS 0
# these are the pins for SWD debugging with a STlinkv2 or black-magic probe
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
# SPI1 - internal sensors
PG11 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PD7 SPI1_MOSI SPI1
# SPI2 - FRAM
PI1 SPI2_SCK SPI2
PI2 SPI2_MISO SPI2
PI3 SPI2_MOSI SPI2
# SPI4 - sensors2
PE2 SPI4_SCK SPI4
PE13 SPI4_MISO SPI4
PE6 SPI4_MOSI SPI4
# SPI5 - external1
PF7 SPI5_SCK SPI5
PF8 SPI5_MISO SPI5
PF9 SPI5_MOSI SPI5
# SPI6 - external2
PG13 SPI6_SCK SPI6
PG12 SPI6_MISO SPI6
PA7 SPI6_MOSI SPI6
# sensor
PF10 ADIS16470_CS CS
PF2 RM3100_CS CS
PG6 ICM20689_CS CS SPEED_VERYLOW
PI12 ICM20649_CS CS SPEED_VERYLOW
PF3 BMI088_A_CS CS
PF4 BMI088_G_CS CS
PF5 FRAM_CS CS SPEED_VERYLOW
PG10 MS5611_IMU_CS CS
PI8 MS5611_BOARD_CS CS
# external CS pins, SPI5 connector
PI4 EXT1_CS1 CS
PI10 EXT1_CS2 CS
PI13 EXT1_CS3 CS
# I2C buses
# I2C1 is on GPS port
PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1
# I2C2 on GPS2 connector
PF1 I2C2_SCL I2C2
PF0 I2C2_SDA I2C2
# I2C3 for onboard mag
PH7 I2C3_SCL I2C3
PH8 I2C3_SDA I2C3
# I2C4 is on BDMA on DMAMUX2
PF14 I2C4_SCL I2C4
PF15 I2C4_SDA I2C4
# order of I2C buses
I2C_ORDER I2C3 I2C1 I2C2 I2C4
define HAL_I2C_INTERNAL_MASK 1
# enable pins
PE3 VDD_3V3_SENSORS_EN OUTPUT LOW
# start peripheral power off, then enable after init
# this prevents a problem with radios that use RTS for
# bootloader hold
PD11 VDD_5V_HIPOWER_EN OUTPUT HIGH
PG4 VDD_5V_PERIPH_EN OUTPUT HIGH
PG5 VDD_5V_RC_EN OUTPUT HIGH
PG7 VDD_3V3_SD_CARD_EN OUTPUT HIGH
# drdy pins
PE7 DRDY1_ADIS16470 INPUT GPIO(93)
PH5 DRDY2_ICM20649 INPUT
PB14 DRDY3_BMI088_GYRO1 INPUT
PB15 DRDY4_BMI088_ACC1 INPUT
PJ0 DRDY5_ICM20689 INPUT
PC13 DRDY6_BMI088_GYRO2 INPUT
PI14 DRDY7_BMI088_ACC2 INPUT
PE4 DRDY8_RM3100 INPUT
# use GPIO(93) for data ready on ADIS16470
define ADIS_DRDY_PIN 93
# UARTs
# USART2 is telem1
PD6 USART2_RX USART2
PD5 USART2_TX USART2
PD3 USART2_CTS USART2
PD4 USART2_RTS USART2
# USART1 is GPS1
PB7 USART1_RX USART1 NODMA
PB6 USART1_TX USART1 NODMA
# UART4 GPS2
PD0 UART4_RX UART4 NODMA
PD1 UART4_TX UART4 NODMA
# USART6 is telem2
PG9 USART6_RX USART6
PG14 USART6_TX USART6
PG15 USART6_CTS USART6
PG8 USART6_RTS USART6
# UART7 is debug
PF6 UART7_RX UART7 NODMA
PE8 UART7_TX UART7 NODMA
# SBUS, DSM port
PE0 UART8_RX UART8
PE1 UART8_TX UART8
# PWM AUX channels
PH10 TIM5_CH1 TIM5 PWM(1) GPIO(50)
PH11 TIM5_CH2 TIM5 PWM(2) GPIO(51)
PH12 TIM5_CH3 TIM5 PWM(3) GPIO(52)
PI0 TIM5_CH4 TIM5 PWM(4) GPIO(53)
PD12 TIM4_CH1 TIM4 PWM(5) GPIO(54)
PD13 TIM4_CH2 TIM4 PWM(6) GPIO(55)
PD14 TIM4_CH3 TIM4 PWM(7) GPIO(56)
PD15 TIM4_CH4 TIM4 PWM(8) GPIO(57)
PE9 TIM1_CH1 TIM1 PWM(9) GPIO(58)
PE11 TIM1_CH2 TIM1 PWM(10) GPIO(59)
PA10 TIM1_CH3 TIM1 PWM(11) GPIO(60)
PE14 TIM1_CH4 TIM1 PWM(12) GPIO(61)
PH6 TIM12_CH1 TIM12 PWM(13) GPIO(62) NODMA
PH9 TIM12_CH2 TIM12 PWM(14) GPIO(63) NODMA
# allow for 14 PWMs by default
define BOARD_PWM_COUNT_DEFAULT 14
# PWM output for buzzer
PE5 TIM15_CH1 TIM15 GPIO(77) ALARM
# RC input
PB4 TIM3_CH1 TIM3 RCININT PULLUP LOW
# analog in
PA0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PA1 BATT_CURRENT_SENS ADC1 SCALE(1)
# ADC3.3/ADC6.6
PC4 SPARE1_ADC1 ADC1 SCALE(1)
PA4 SPARE2_ADC1 ADC1 SCALE(1)
PF12 RSSI_IN ADC1 SCALE(1)
PC5 VDD_5V_SENS ADC1 SCALE(2)
PC1 SCALED_V3V3 ADC1 SCALE(2)
# CAN bus
PI9 CAN1_RX CAN1
PH13 CAN1_TX CAN1
# 2nd CAN bus. Cannot be used at same time as USB_HS
PB12 CAN2_RX CAN2
PB13 CAN2_TX CAN2
# control for silent (no output) for CAN
PH2 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(70)
PH3 GPIO_CAN2_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(71)
# GPIOs
PA8 HEATER_EN OUTPUT LOW GPIO(80)
define HAL_HEATER_GPIO_PIN 80
define HAL_HAVE_IMU_HEATER 1
PG1 VDD_BRICK_VALID INPUT PULLUP
PG2 VDD_BRICK2_VALID INPUT PULLUP
PG0 nVBUS INPUT PULLUP
PJ3 VDD_5V_HIPOWER_OC INPUT PULLUP
PJ4 VDD_5V_PERIPH_OC INPUT PULLUP
PB10 nSPI5_RESET_EXTERNAL1 OUTPUT HIGH
# SPI devices
SPIDEV adis16470 SPI1 DEVID2 ADIS16470_CS MODE3 1*MHZ 2*MHZ
SPIDEV icm20689 SPI1 DEVID2 ICM20689_CS MODE3 2*MHZ 8*MHZ
SPIDEV bmi088_a SPI4 DEVID2 BMI088_A_CS MODE3 10*MHZ 10*MHZ
SPIDEV bmi088_g SPI4 DEVID3 BMI088_G_CS MODE3 10*MHZ 10*MHZ
SPIDEV ms5611_imu SPI4 DEVID1 MS5611_IMU_CS MODE3 20*MHZ 20*MHZ
SPIDEV ms5611_board SPI6 DEVID1 MS5611_BOARD_CS MODE3 20*MHZ 20*MHZ
SPIDEV icm20649 SPI6 DEVID2 ICM20649_CS MODE3 2*MHZ 8*MHZ
SPIDEV ramtron SPI2 DEVID1 FRAM_CS MODE3 8*MHZ 8*MHZ
# RM3100 may be on SPI1 or SPI2 (not both). Later board revisions
# have the RM3100 on SPI2, to leave SPI1 free for ADIS1647x
SPIDEV rm3100-1 SPI1 DEVID1 RM3100_CS MODE3 2*MHZ 8*MHZ
SPIDEV rm3100-2 SPI2 DEVID2 RM3100_CS MODE3 2*MHZ 8*MHZ
# two baro
BARO MS56XX SPI:ms5611_imu
BARO MS56XX SPI:ms5611_board
# three IMUs, only one of ICM20689 and ADIS16470 will be included
IMU ADIS1647x SPI:adis16470 ROTATION_PITCH_180_YAW_270 ADIS_DRDY_PIN
IMU Invensense SPI:icm20689 ROTATION_NONE
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_PITCH_180_YAW_270
IMU Invensensev2 SPI:icm20649 ROTATION_NONE
define HAL_DEFAULT_INS_FAST_SAMPLE 5
# compasses
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
COMPASS IST8310 I2C:ALL_EXTERNAL:0x0E true ROTATION_ROLL_180_YAW_90
COMPASS IST8310 I2C:ALL_INTERNAL:0x0E false ROTATION_ROLL_180_YAW_90
# probe for RM3100 on SPI1 or SPI2
COMPASS RM3100 SPI:rm3100-1 false ROTATION_NONE
COMPASS RM3100 SPI:rm3100-2 false ROTATION_NONE
# microSD support
PC8 SDMMC1_D0 SDMMC1
PC9 SDMMC1_D1 SDMMC1
PC10 SDMMC1_D2 SDMMC1
PC11 SDMMC1_D3 SDMMC1
PC12 SDMMC1_CK SDMMC1
PD2 SDMMC1_CMD SDMMC1
# red LED marked as B/E
PI5 LED_R1 OUTPUT OPENDRAIN HIGH GPIO(0)
PI6 LED_G1 OUTPUT OPENDRAIN LOW GPIO(1)
PI7 LED_B1 OUTPUT OPENDRAIN HIGH GPIO(2)
define HAL_GPIO_A_LED_PIN 0
define HAL_GPIO_B_LED_PIN 1
define HAL_GPIO_C_LED_PIN 2
define HAL_GPIO_LED_ON 0
define HAL_GPIO_LED_OFF 1
# use pixracer style 3-LED indicators
define HAL_HAVE_PIXRACER_LED
# enable RAMTROM parameter storage
define HAL_STORAGE_SIZE 16384
define HAL_WITH_RAMTRON 1
# allow to have have a dedicated safety switch pin
define HAL_HAVE_SAFETY_SWITCH 1
PE12 LED_SAFETY OUTPUT
PE10 SAFETY_IN INPUT PULLDOWN
# enable FAT filesystem support (needs a microSD defined via SDMMC)
define HAL_OS_FATFS_IO 1
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
DMA_PRIORITY ADC* SPI1* TIM*UP*
DMA_NOSHARE SPI1* TIM*UP*
# default to 45C target temp
define HAL_IMU_TEMP_DEFAULT 45