mirror of
https://github.com/ArduPilot/ardupilot
synced 2025-01-19 23:28:32 -04:00
3558567aad
no roll and pitch input means no change. Flicking will still update the throttle cruise value. Please check I have the signs correct!!! git-svn-id: https://arducopter.googlecode.com/svn/trunk@1499 f9c3cf11-9bcb-44bc-f272-b75c42450872
115 lines
2.5 KiB
Plaintext
115 lines
2.5 KiB
Plaintext
void read_control_switch()
|
|
{
|
|
byte switchPosition = readSwitch();
|
|
//motor_armed = (switchPosition < 5);
|
|
|
|
if (oldSwitchPosition != switchPosition){
|
|
if(motor_armed)
|
|
Serial.println("motor_armed");
|
|
else
|
|
Serial.println("motor disarmed");
|
|
|
|
set_mode(flight_modes[switchPosition]);
|
|
|
|
oldSwitchPosition = switchPosition;
|
|
|
|
// reset navigation integrators
|
|
// -------------------------
|
|
reset_I();
|
|
}
|
|
}
|
|
|
|
byte readSwitch(void){
|
|
#if FLIGHT_MODE_CHANNEL == CH_5
|
|
int pulsewidth = rc_5.radio_in; // default for Arducopter
|
|
#elif FLIGHT_MODE_CHANNEL == CH_6
|
|
int pulsewidth = rc_6.radio_in; //
|
|
#elif FLIGHT_MODE_CHANNEL == CH_7
|
|
int pulsewidth = rc_7.radio_in; //
|
|
#elif FLIGHT_MODE_CHANNEL == CH_8
|
|
int pulsewidth = rc_8.radio_in; // default for Ardupilot. Don't use for Arducopter! it has a hardware failsafe mux!
|
|
#else
|
|
# error Must define FLIGHT_MODE_CHANNEL as CH_5 - CH_8
|
|
#endif
|
|
|
|
if (pulsewidth > 1230 && pulsewidth <= 1360) return 1;
|
|
if (pulsewidth > 1360 && pulsewidth <= 1490) return 2;
|
|
if (pulsewidth > 1490 && pulsewidth <= 1620) return 3;
|
|
if (pulsewidth > 1620 && pulsewidth <= 1749) return 4; // Software Manual
|
|
if (pulsewidth >= 1750) return 5; // Hardware Manual
|
|
return 0;
|
|
}
|
|
|
|
void reset_control_switch()
|
|
{
|
|
oldSwitchPosition = -1;
|
|
read_control_switch();
|
|
//Serial.print("MSG: reset_control_switch");
|
|
//Serial.println(oldSwitchPosition , DEC);
|
|
}
|
|
|
|
void update_servo_switches()
|
|
{
|
|
|
|
}
|
|
|
|
boolean trim_flag;
|
|
unsigned long trim_timer;
|
|
|
|
// read at 10 hz
|
|
// set this to your trainer switch
|
|
void read_trim_switch()
|
|
{
|
|
// switch is engaged
|
|
if (rc_7.control_in > 500){
|
|
if(trim_flag == false){
|
|
// called once
|
|
trim_timer = millis();
|
|
}
|
|
|
|
trim_flag = true;
|
|
trim_accel();
|
|
|
|
|
|
}else{ // switch is disengaged
|
|
|
|
if(trim_flag){
|
|
// switch was just released
|
|
if((millis() - trim_timer) > 2000){
|
|
|
|
// not being used
|
|
|
|
} else {
|
|
|
|
// set the throttle nominal
|
|
if(rc_3.control_in > 50){
|
|
throttle_cruise = rc_3.control_in;
|
|
//Serial.print("tnom ");
|
|
//Serial.println(throttle_cruise, DEC);
|
|
save_EEPROM_throttle_cruise();
|
|
}
|
|
}
|
|
trim_flag = false;
|
|
}
|
|
}
|
|
}
|
|
|
|
|
|
void trim_accel()
|
|
{
|
|
if(rc_1.control_in > 0){
|
|
imu.ay(imu.ay() + 1);
|
|
}else if (rc_1.control_in < 0){
|
|
imu.ay(imu.ay() - 1);
|
|
}
|
|
|
|
if(rc_2.control_in > 0){
|
|
imu.ax(imu.ax() + 1);
|
|
}else if (rc_2.control_in < 0){
|
|
imu.ax(imu.ax() - 1);
|
|
}
|
|
|
|
Serial.printf("r:%ld p:%ld ax:%d, ay:%d, az:%d\n", dcm.roll_sensor, dcm.pitch_sensor, imu.ax(), imu.ay(), imu.az());
|
|
}
|
|
|