mirror of https://github.com/ArduPilot/ardupilot
217 lines
7.1 KiB
C++
217 lines
7.1 KiB
C++
/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
/*
|
|
This program is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
/*
|
|
* APM_Airspeed.cpp - airspeed (pitot) driver
|
|
*/
|
|
|
|
|
|
#include <AP_HAL.h>
|
|
#include <AP_Math.h>
|
|
#include <AP_Common.h>
|
|
#include <AP_ADC.h>
|
|
#include <AP_Airspeed.h>
|
|
|
|
extern const AP_HAL::HAL& hal;
|
|
|
|
#if CONFIG_HAL_BOARD == HAL_BOARD_APM1
|
|
#include <AP_ADC_AnalogSource.h>
|
|
#define ARSPD_DEFAULT_PIN 64
|
|
#elif CONFIG_HAL_BOARD == HAL_BOARD_APM2
|
|
#define ARSPD_DEFAULT_PIN 0
|
|
#elif CONFIG_HAL_BOARD == HAL_BOARD_AVR_SITL
|
|
#define ARSPD_DEFAULT_PIN 1
|
|
#elif CONFIG_HAL_BOARD == HAL_BOARD_PX4
|
|
#include <sys/stat.h>
|
|
#include <sys/types.h>
|
|
#include <fcntl.h>
|
|
#include <unistd.h>
|
|
#include <systemlib/airspeed.h>
|
|
#include <drivers/drv_airspeed.h>
|
|
#include <uORB/topics/differential_pressure.h>
|
|
#ifdef CONFIG_ARCH_BOARD_PX4FMU_V1
|
|
#define ARSPD_DEFAULT_PIN 11
|
|
#else
|
|
#define ARSPD_DEFAULT_PIN 15
|
|
#endif
|
|
#elif CONFIG_HAL_BOARD == HAL_BOARD_FLYMAPLE
|
|
#define ARSPD_DEFAULT_PIN 16
|
|
#elif CONFIG_HAL_BOARD == HAL_BOARD_LINUX
|
|
#define ARSPD_DEFAULT_PIN AP_AIRSPEED_I2C_PIN
|
|
#else
|
|
#define ARSPD_DEFAULT_PIN 0
|
|
#endif
|
|
|
|
// table of user settable parameters
|
|
const AP_Param::GroupInfo AP_Airspeed::var_info[] PROGMEM = {
|
|
|
|
// @Param: ENABLE
|
|
// @DisplayName: Airspeed enable
|
|
// @Description: enable airspeed sensor
|
|
// @Values: 0:Disable,1:Enable
|
|
AP_GROUPINFO("ENABLE", 0, AP_Airspeed, _enable, 1),
|
|
|
|
// @Param: USE
|
|
// @DisplayName: Airspeed use
|
|
// @Description: use airspeed for flight control
|
|
// @Values: 1:Use,0:Don't Use
|
|
AP_GROUPINFO("USE", 1, AP_Airspeed, _use, 0),
|
|
|
|
// @Param: OFFSET
|
|
// @DisplayName: Airspeed offset
|
|
// @Description: Airspeed calibration offset
|
|
// @Increment: 0.1
|
|
AP_GROUPINFO("OFFSET", 2, AP_Airspeed, _offset, 0),
|
|
|
|
// @Param: RATIO
|
|
// @DisplayName: Airspeed ratio
|
|
// @Description: Airspeed calibration ratio
|
|
// @Increment: 0.1
|
|
AP_GROUPINFO("RATIO", 3, AP_Airspeed, _ratio, 1.9936f),
|
|
|
|
// @Param: PIN
|
|
// @DisplayName: Airspeed pin
|
|
// @Description: The analog pin number that the airspeed sensor is connected to. Set this to 0..9 for the APM2 analog pins. Set to 64 on an APM1 for the dedicated airspeed port on the end of the board. Set to 11 on PX4 for the analog airspeed port. Set to 15 on the Pixhawk for the analog airspeed port. Set to 65 on the PX4 or Pixhawk for an EagleTree or MEAS I2C airspeed sensor.
|
|
// @User: Advanced
|
|
AP_GROUPINFO("PIN", 4, AP_Airspeed, _pin, ARSPD_DEFAULT_PIN),
|
|
|
|
// @Param: AUTOCAL
|
|
// @DisplayName: Automatic airspeed ratio calibration
|
|
// @Description: If this is enabled then the APM will automatically adjust the ARSPD_RATIO during flight, based upon an estimation filter using ground speed and true airspeed. The automatic calibration will save the new ratio to EEPROM every 2 minutes if it changes by more than 5%
|
|
// @User: Advanced
|
|
AP_GROUPINFO("AUTOCAL", 5, AP_Airspeed, _autocal, 0),
|
|
|
|
// @Param: TUBE_ORDER
|
|
// @DisplayName: Control pitot tube order
|
|
// @Description: This parameter allows you to control whether the order in which the tubes are attached to your pitot tube matters. If you set this to 0 then the top connector on the sensor needs to be the dynamic pressure. If set to 1 then the bottom connector needs to be the dynamic pressure. If set to 2 (the default) then the airspeed driver will accept either order. The reason you may wish to specify the order is it will allow your airspeed sensor to detect if the aircraft it receiving excessive pressure on the static port, which would otherwise be seen as a positive airspeed.
|
|
// @User: Advanced
|
|
AP_GROUPINFO("TUBE_ORDER", 6, AP_Airspeed, _tube_order, 2),
|
|
|
|
AP_GROUPEND
|
|
};
|
|
|
|
|
|
/*
|
|
this scaling factor converts from the old system where we used a
|
|
0 to 4095 raw ADC value for 0-5V to the new system which gets the
|
|
voltage in volts directly from the ADC driver
|
|
*/
|
|
#define SCALING_OLD_CALIBRATION 819 // 4095/5
|
|
|
|
void AP_Airspeed::init()
|
|
{
|
|
_last_pressure = 0;
|
|
_calibration.init(_ratio);
|
|
_last_saved_ratio = _ratio;
|
|
_counter = 0;
|
|
|
|
analog.init();
|
|
digital.init();
|
|
}
|
|
|
|
// read the airspeed sensor
|
|
float AP_Airspeed::get_pressure(void)
|
|
{
|
|
if (!_enable) {
|
|
return 0;
|
|
}
|
|
float pressure = 0;
|
|
if (_pin == AP_AIRSPEED_I2C_PIN) {
|
|
_healthy = digital.get_differential_pressure(pressure);
|
|
} else {
|
|
_healthy = analog.get_differential_pressure(pressure);
|
|
}
|
|
return pressure;
|
|
}
|
|
|
|
// get a temperature reading if possible
|
|
bool AP_Airspeed::get_temperature(float &temperature)
|
|
{
|
|
if (!_enable) {
|
|
return false;
|
|
}
|
|
if (_pin == AP_AIRSPEED_I2C_PIN) {
|
|
return digital.get_temperature(temperature);
|
|
}
|
|
return false;
|
|
}
|
|
|
|
// calibrate the airspeed. This must be called at least once before
|
|
// the get_airspeed() interface can be used
|
|
void AP_Airspeed::calibrate()
|
|
{
|
|
float sum = 0;
|
|
uint8_t count = 0;
|
|
if (!_enable) {
|
|
return;
|
|
}
|
|
// discard first reading
|
|
get_pressure();
|
|
for (uint8_t i = 0; i < 10; i++) {
|
|
hal.scheduler->delay(100);
|
|
float p = get_pressure();
|
|
if (_healthy) {
|
|
sum += p;
|
|
count++;
|
|
}
|
|
}
|
|
if (count == 0) {
|
|
// unhealthy sensor
|
|
hal.console->println_P(PSTR("Airspeed sensor unhealthy"));
|
|
_offset.set(0);
|
|
return;
|
|
}
|
|
float raw = sum/count;
|
|
_offset.set_and_save(raw);
|
|
_airspeed = 0;
|
|
_raw_airspeed = 0;
|
|
}
|
|
|
|
// read the airspeed sensor
|
|
void AP_Airspeed::read(void)
|
|
{
|
|
float airspeed_pressure;
|
|
if (!_enable) {
|
|
return;
|
|
}
|
|
airspeed_pressure = get_pressure() - _offset;
|
|
|
|
/*
|
|
we support different pitot tube setups so used can choose if
|
|
they want to be able to detect pressure on the static port
|
|
*/
|
|
switch ((enum pitot_tube_order)_tube_order.get()) {
|
|
case PITOT_TUBE_ORDER_NEGATIVE:
|
|
airspeed_pressure = -airspeed_pressure;
|
|
// fall thru
|
|
case PITOT_TUBE_ORDER_POSITIVE:
|
|
if (airspeed_pressure < -32) {
|
|
// we're reading more than about -8m/s. The user probably has
|
|
// the ports the wrong way around
|
|
_healthy = false;
|
|
}
|
|
break;
|
|
case PITOT_TUBE_ORDER_AUTO:
|
|
default:
|
|
airspeed_pressure = fabsf(airspeed_pressure);
|
|
break;
|
|
}
|
|
airspeed_pressure = max(airspeed_pressure, 0);
|
|
_last_pressure = airspeed_pressure;
|
|
_raw_airspeed = sqrtf(airspeed_pressure * _ratio);
|
|
_airspeed = 0.7f * _airspeed + 0.3f * _raw_airspeed;
|
|
_last_update_ms = hal.scheduler->millis();
|
|
}
|