ed58758ce6
setting up a DEFAULTGPIO pulldown in bootloaders is a bad idea as it overrides any hardware pullups that have been put in place as part of a "hold in bootloader" mechanism. See discussion in #27360 for ELRS note that this only impacts one board that I can see, the BlitzF745AIO, due to the MCU vs DEFAULTGPIO interaction |
||
|---|---|---|
| .. | ||
| README.md | ||
| blitz_h7_pro.png | ||
| defaults.parm | ||
| hwdef-bl.dat | ||
| hwdef.dat | ||
README.md
iFlight BLITZ H7 Pro Flight Controller
The Blitz H7 Pro is a flight controller produced by iFlight.
Features
- MCU - STM32H743 32-bit processor running at 480 MHz
- Gyro: ICM42688
- 32Gb SDCard for logging
- BEC output: 5V 2.5A, switch controlled 12v 2A
- Barometer: DPS310
- OSD: AT7456E
- 7x UARTs
- 13x PWM Outputs (12 Motor Output, 1 LED)
- Battery input voltage: 2S-8S
- 2x I2C for external compass, airspeed, etc.
- CAN port
Pinout
back side pinout image pending from iFlight
The expansion connector provides access to the following pins:
- CAN+/CAN-
- M9 through M12
- TX7/RX7
- SCL2/SDA2
- RSSI
- 5V/12V/GND
UART Mapping
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
| Name | Pin | Function |
|---|---|---|
| SERIAL0 | COMPUTER | USB |
| SERIAL1 | RX1/TX1 | UART1 (DJI connector, DMA-enabled) |
| SERIAL2 | TX2/RX2 | UART2 (RX, DMA-enabled) |
| SERIAL3 | TX3/RX3 | UART3 (DMA-enabled) |
| SERIAL4 | TX4/RX4 | UART4 (GPS, DMA-enabled) |
| SERIAL5 | RX5 | UART5 (ESC Telemetry) |
| SERIAL6 | TX6/RX6 | UART6 |
| SERIAL7 | TX7/RX7 | UART7 |
RC Input
RC input is configured on the (UART2_RX/UART2_TX) pins which forms part of the DJI connector. It supports all serial RC protocols.
OSD Support
The BLITZ H7 Pro supports OSD using OSD_TYPE 1 (MAX7456 driver).
PWM Output
The BLITZ H7 Pro has 13 PWM outputs. The pads for motor output M1-M4 are in one ESC connector and M5-M8 in the second ESC connector. The remaining outputs are on the pads on the daughterboard. The first 8 outputs support bi-directional DShot and DShot, as well as all PWM types. Outputs 9-10 support DShot, as well as all PWM types and outputs 11-12 only support PWM.
The PWM are in in five groups:
-
PWM 1-2 in group1
-
PWM 3-6 in group2
-
PWM 7-10 in group3
-
PWM 11-12 in group4
-
PWM 13 in group5 .. note:: for users migrating from BetaflightX quads, the first four outputs M1-M4 have been configured for use with existing motor wiring using these default parameters:
-
:ref:
FRAME_CLASS<FRAME_CLASS>= 1 (Quad) -
:ref:
FRAME_TYPE<FRAME_TYPE>= 12 (BetaFlightX)
Channels within the same group need to use the same output rate. If any channel in a group uses DShot then all channels in the group need to use DShot.
Video Power Control
The 12V video power can be turned off/on using GPIO 81 which is already assigned by default to RELAY2. This relay can be controlled either from the GCS or using a transmitter channel (See :ref:common-auxiliary-functions)
RSSI
Analog RSSI pin is "4"
Battery Monitoring
The board has a builtin voltage sensor and a current sensor input tied to its 4 in 1 ESC current sensor. The voltage sensor can handle up to 6S LiPo batteries.
The correct battery setting parameters are:
- BATT_MONITOR 4
- BATT_VOLT_PIN 10
- BATT_VOLT_MULT 11
- BATT_CURR_PIN 11
- BATT_CURR_MULT 50
These are set by default in the firmware and shouldn't need to be adjusted
Compass
The BLITZ H7 Pro does not have a builtin compass, but you can attach an external compass to I2C pins.
Loading Firmware
Initial firmware load can be done with DFU by plugging in USB with the bootloader button pressed. Then you should load the "with_bl.hex" firmware, using your favourite DFU loading tool.
Once the initial firmware is loaded you can update the firmware using any ArduPilot ground station software. Updates should be done with the *.apj firmware files.