ardupilot/ArduCopter/Parameters.h

540 lines
18 KiB
C++

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
#ifndef PARAMETERS_H
#define PARAMETERS_H
#include <AP_Common.h>
// Global parameter class.
//
class Parameters {
public:
// The version of the layout as described by the parameter enum.
//
// When changing the parameter enum in an incompatible fashion, this
// value should be incremented by one.
//
// The increment will prevent old parameters from being used incorrectly
// by newer code.
//
static const uint16_t k_format_version = 120;
// The parameter software_type is set up solely for ground station use
// and identifies the software type (eg ArduPilotMega versus
// ArduCopterMega)
// GCS will interpret values 0-9 as ArduPilotMega. Developers may use
// values within that range to identify different branches.
//
static const uint16_t k_software_type = 10; // 0 for APM
// trunk
// Parameter identities.
//
// The enumeration defined here is used to ensure that every parameter
// or parameter group has a unique ID number. This number is used by
// AP_Param to store and locate parameters in EEPROM.
//
// Note that entries without a number are assigned the next number after
// the entry preceding them. When adding new entries, ensure that they
// don't overlap.
//
// Try to group related variables together, and assign them a set
// range in the enumeration. Place these groups in numerical order
// at the end of the enumeration.
//
// WARNING: Care should be taken when editing this enumeration as the
// AP_Param load/save code depends on the values here to identify
// variables saved in EEPROM.
//
//
enum {
// Layout version number, always key zero.
//
k_param_format_version = 0,
k_param_software_type,
k_param_ins_old, // *** Deprecated, remove with next eeprom number change
k_param_ins, // libraries/AP_InertialSensor variables
// simulation
k_param_sitl = 10,
// barometer object (needed for SITL)
k_param_barometer,
// scheduler object (for debugging)
k_param_scheduler,
// relay object
k_param_relay,
// EPM object
k_param_epm,
// BoardConfig object
k_param_BoardConfig,
// GPS object
k_param_gps,
// Parachute object
k_param_parachute, // 17
// Landing gear object
k_param_landinggear, // 18
// Misc
//
k_param_log_bitmask_old = 20, // Deprecated
k_param_log_last_filenumber, // *** Deprecated - remove
// with next eeprom number
// change
k_param_toy_yaw_rate, // deprecated - remove
k_param_crosstrack_min_distance, // deprecated - remove with next eeprom number change
k_param_rssi_pin,
k_param_throttle_accel_enabled, // deprecated - remove
k_param_wp_yaw_behavior,
k_param_acro_trainer,
k_param_pilot_velocity_z_max,
k_param_circle_rate, // deprecated - remove
k_param_sonar_gain,
k_param_ch8_option,
k_param_arming_check,
k_param_sprayer,
k_param_angle_max,
k_param_gps_hdop_good,
k_param_battery,
k_param_fs_batt_mah,
k_param_angle_rate_max, // remove
k_param_rssi_range,
k_param_rc_feel_rp,
k_param_NavEKF, // Extended Kalman Filter Inertial Navigation Group
k_param_mission, // mission library
k_param_rc_13,
k_param_rc_14,
k_param_rally,
k_param_poshold_brake_rate,
k_param_poshold_brake_angle_max,
k_param_pilot_accel_z,
k_param_serial0_baud,
k_param_serial1_baud,
k_param_serial2_baud,
k_param_land_repositioning,
k_param_sonar, // sonar object
k_param_ekfcheck_thresh,
k_param_terrain,
k_param_acro_expo,
k_param_throttle_deadzone,
k_param_optflow,
k_param_dcmcheck_thresh, // 59
k_param_log_bitmask,
// 65: AP_Limits Library
k_param_limits = 65, // deprecated - remove
k_param_gpslock_limit, // deprecated - remove
k_param_geofence_limit, // deprecated - remove
k_param_altitude_limit, // deprecated - remove
k_param_fence,
k_param_gps_glitch,
k_param_baro_glitch, // 71
//
// 75: Singlecopter, CoaxCopter
//
k_param_single_servo_1 = 75,
k_param_single_servo_2,
k_param_single_servo_3,
k_param_single_servo_4, // 78
//
// 80: Heli
//
k_param_heli_servo_1 = 80,
k_param_heli_servo_2,
k_param_heli_servo_3,
k_param_heli_servo_4,
k_param_heli_pitch_ff, // remove
k_param_heli_roll_ff, // remove
k_param_heli_yaw_ff, // remove
k_param_heli_stab_col_min,
k_param_heli_stab_col_max, // 88
//
// 90: Motors
//
k_param_motors = 90,
//
// 100: Inertial Nav
//
k_param_inertial_nav = 100,
k_param_wp_nav,
k_param_attitude_control,
k_param_pos_control,
k_param_circle_nav, // 104
// 110: Telemetry control
//
k_param_gcs0 = 110,
k_param_gcs1,
k_param_sysid_this_mav,
k_param_sysid_my_gcs,
k_param_serial1_baud_old, // deprecated
k_param_telem_delay,
k_param_gcs2,
k_param_serial2_baud_old, // deprecated
k_param_serial2_protocol,
//
// 140: Sensor parameters
//
k_param_imu = 140, // deprecated - can be deleted
k_param_battery_monitoring = 141, // deprecated - can be deleted
k_param_volt_div_ratio, // deprecated - can be deleted
k_param_curr_amp_per_volt, // deprecated - can be deleted
k_param_input_voltage, // deprecated - can be deleted
k_param_pack_capacity, // deprecated - can be deleted
k_param_compass_enabled,
k_param_compass,
k_param_sonar_enabled_old, // deprecated
k_param_frame_orientation,
k_param_optflow_enabled, // deprecated
k_param_fs_batt_voltage,
k_param_ch7_option,
k_param_auto_slew_rate, // deprecated - can be deleted
k_param_sonar_type_old, // deprecated
k_param_super_simple = 155,
k_param_axis_enabled = 157, // deprecated - remove with next eeprom number change
k_param_copter_leds_mode, // deprecated - remove with next eeprom number change
k_param_ahrs, // AHRS group // 159
//
// 160: Navigation parameters
//
k_param_rtl_altitude = 160,
k_param_crosstrack_gain, // deprecated - remove with next eeprom number change
k_param_rtl_loiter_time,
k_param_rtl_alt_final,
k_param_tilt_comp, //164 deprecated - remove with next eeprom number change
//
// Camera and mount parameters
//
k_param_camera = 165,
k_param_camera_mount,
k_param_camera_mount2, // deprecated
//
// Batery monitoring parameters
//
k_param_battery_volt_pin = 168, // deprecated - can be deleted
k_param_battery_curr_pin, // 169 deprecated - can be deleted
//
// 170: Radio settings
//
k_param_rc_1 = 170,
k_param_rc_2,
k_param_rc_3,
k_param_rc_4,
k_param_rc_5,
k_param_rc_6,
k_param_rc_7,
k_param_rc_8,
k_param_rc_10,
k_param_rc_11,
k_param_throttle_min,
k_param_throttle_max,
k_param_failsafe_throttle,
k_param_throttle_fs_action, // remove
k_param_failsafe_throttle_value,
k_param_throttle_cruise,
k_param_esc_calibrate,
k_param_radio_tuning,
k_param_radio_tuning_high,
k_param_radio_tuning_low,
k_param_rc_speed = 192,
k_param_failsafe_battery_enabled,
k_param_throttle_mid,
k_param_failsafe_gps_enabled,
k_param_rc_9,
k_param_rc_12,
k_param_failsafe_gcs, // 198
k_param_rcmap,
//
// 200: flight modes
//
k_param_flight_mode1 = 200,
k_param_flight_mode2,
k_param_flight_mode3,
k_param_flight_mode4,
k_param_flight_mode5,
k_param_flight_mode6,
k_param_simple_modes,
//
// 210: Waypoint data
//
k_param_waypoint_mode = 210, // remove
k_param_command_total, // remove
k_param_command_index, // remove
k_param_command_nav_index, // remove
k_param_waypoint_radius, // remove
k_param_circle_radius, // remove
k_param_waypoint_speed_max, // remove
k_param_land_speed,
k_param_auto_velocity_z_min, // remove
k_param_auto_velocity_z_max, // remove - 219
//
// 220: PI/D Controllers
//
k_param_acro_rp_p = 221,
k_param_axis_lock_p, // remove
k_param_pid_rate_roll,
k_param_pid_rate_pitch,
k_param_pid_rate_yaw,
k_param_p_stabilize_roll,
k_param_p_stabilize_pitch,
k_param_p_stabilize_yaw,
k_param_p_loiter_pos,
k_param_p_loiter_lon, // remove
k_param_pid_loiter_rate_lat,
k_param_pid_loiter_rate_lon,
k_param_pid_nav_lat, // 233 - remove
k_param_pid_nav_lon, // 234 - remove
k_param_p_alt_hold,
k_param_p_throttle_rate,
k_param_pid_optflow_roll, // 237 - remove
k_param_pid_optflow_pitch, // 238 - remove
k_param_acro_balance_roll_old, // 239 - remove
k_param_acro_balance_pitch_old, // 240 - remove
k_param_pid_throttle_accel,
k_param_acro_balance_roll,
k_param_acro_balance_pitch,
k_param_acro_yaw_p, // 244
// 254,255: reserved
};
AP_Int16 format_version;
AP_Int8 software_type;
// Telemetry control
//
AP_Int16 sysid_this_mav;
AP_Int16 sysid_my_gcs;
AP_Int16 serial0_baud;
AP_Int16 serial1_baud;
#if MAVLINK_COMM_NUM_BUFFERS > 2
AP_Int16 serial2_baud;
AP_Int8 serial2_protocol;
#endif
AP_Int8 telem_delay;
AP_Int16 rtl_altitude;
AP_Float sonar_gain;
AP_Int8 failsafe_battery_enabled; // battery failsafe enabled
AP_Float fs_batt_voltage; // battery voltage below which failsafe will be triggered
AP_Float fs_batt_mah; // battery capacity (in mah) below which failsafe will be triggered
AP_Int8 failsafe_gps_enabled; // gps failsafe enabled
AP_Int8 failsafe_gcs; // ground station failsafe behavior
AP_Int16 gps_hdop_good; // GPS Hdop value at or below this value represent a good position
AP_Int8 compass_enabled;
AP_Int8 super_simple;
AP_Int16 rtl_alt_final;
AP_Int8 rssi_pin;
AP_Float rssi_range; // allows to set max voltage for rssi pin such as 5.0, 3.3 etc.
AP_Int8 wp_yaw_behavior; // controls how the autopilot controls yaw during missions
AP_Int8 rc_feel_rp; // controls vehicle response to user input with 0 being extremely soft and 100 begin extremely crisp
AP_Int16 poshold_brake_rate; // PosHold flight mode's rotation rate during braking in deg/sec
AP_Int16 poshold_brake_angle_max; // PosHold flight mode's max lean angle during braking in centi-degrees
// Waypoints
//
AP_Int32 rtl_loiter_time;
AP_Int16 land_speed;
AP_Int16 pilot_velocity_z_max; // maximum vertical velocity the pilot may request
AP_Int16 pilot_accel_z; // vertical acceleration the pilot may request
// Throttle
//
AP_Int16 throttle_min;
AP_Int16 throttle_max;
AP_Int8 failsafe_throttle;
AP_Int16 failsafe_throttle_value;
AP_Int16 throttle_cruise;
AP_Int16 throttle_mid;
AP_Int16 throttle_deadzone;
// Flight modes
//
AP_Int8 flight_mode1;
AP_Int8 flight_mode2;
AP_Int8 flight_mode3;
AP_Int8 flight_mode4;
AP_Int8 flight_mode5;
AP_Int8 flight_mode6;
AP_Int8 simple_modes;
// Misc
//
AP_Int32 log_bitmask;
AP_Int8 esc_calibrate;
AP_Int8 radio_tuning;
AP_Int16 radio_tuning_high;
AP_Int16 radio_tuning_low;
AP_Int8 frame_orientation;
AP_Int8 ch7_option;
AP_Int8 ch8_option;
AP_Int8 arming_check;
AP_Int8 land_repositioning;
AP_Float ekfcheck_thresh;
AP_Float dcmcheck_thresh;
#if FRAME_CONFIG == HELI_FRAME
// Heli
RC_Channel heli_servo_1, heli_servo_2, heli_servo_3, heli_servo_4; // servos for swash plate and tail
AP_Int16 heli_stab_col_min; // min collective while pilot directly controls collective in stabilize mode
AP_Int16 heli_stab_col_max; // min collective while pilot directly controls collective in stabilize mode
#endif
#if FRAME_CONFIG == SINGLE_FRAME
// Single
RC_Channel single_servo_1, single_servo_2, single_servo_3, single_servo_4; // servos for four flaps
#endif
#if FRAME_CONFIG == COAX_FRAME
// Coax copter flaps
RC_Channel single_servo_1, single_servo_2; // servos for two flaps
#endif
// RC channels
RC_Channel rc_1;
RC_Channel rc_2;
RC_Channel rc_3;
RC_Channel rc_4;
RC_Channel_aux rc_5;
RC_Channel_aux rc_6;
RC_Channel_aux rc_7;
RC_Channel_aux rc_8;
#if CONFIG_HAL_BOARD == HAL_BOARD_PX4 || CONFIG_HAL_BOARD == HAL_BOARD_VRBRAIN
RC_Channel_aux rc_9;
#endif
RC_Channel_aux rc_10;
RC_Channel_aux rc_11;
#if CONFIG_HAL_BOARD == HAL_BOARD_PX4 || CONFIG_HAL_BOARD == HAL_BOARD_VRBRAIN
RC_Channel_aux rc_12;
RC_Channel_aux rc_13;
RC_Channel_aux rc_14;
#endif
AP_Int16 rc_speed; // speed of fast RC Channels in Hz
// Acro parameters
AP_Float acro_rp_p;
AP_Float acro_yaw_p;
AP_Float acro_balance_roll;
AP_Float acro_balance_pitch;
AP_Int8 acro_trainer;
AP_Float acro_expo;
// PI/D controllers
#if FRAME_CONFIG == HELI_FRAME
AC_HELI_PID pid_rate_roll;
AC_HELI_PID pid_rate_pitch;
AC_HELI_PID pid_rate_yaw;
#else
AC_PID pid_rate_roll;
AC_PID pid_rate_pitch;
AC_PID pid_rate_yaw;
#endif
AC_PID pid_loiter_rate_lat;
AC_PID pid_loiter_rate_lon;
AC_P p_throttle_rate;
AC_PID pid_throttle_accel;
AC_P p_loiter_pos;
AC_P p_stabilize_roll;
AC_P p_stabilize_pitch;
AC_P p_stabilize_yaw;
AC_P p_alt_hold;
// Note: keep initializers here in the same order as they are declared
// above.
Parameters() :
#if FRAME_CONFIG == HELI_FRAME
heli_servo_1 (CH_1),
heli_servo_2 (CH_2),
heli_servo_3 (CH_3),
heli_servo_4 (CH_4),
#endif
#if FRAME_CONFIG == SINGLE_FRAME
single_servo_1 (CH_1),
single_servo_2 (CH_2),
single_servo_3 (CH_3),
single_servo_4 (CH_4),
#endif
#if FRAME_CONFIG == COAX_FRAME
single_servo_1 (CH_1),
single_servo_2 (CH_2),
#endif
rc_1 (CH_1),
rc_2 (CH_2),
rc_3 (CH_3),
rc_4 (CH_4),
rc_5 (CH_5),
rc_6 (CH_6),
rc_7 (CH_7),
rc_8 (CH_8),
#if CONFIG_HAL_BOARD == HAL_BOARD_PX4 || CONFIG_HAL_BOARD == HAL_BOARD_VRBRAIN
rc_9 (CH_9),
#endif
rc_10 (CH_10),
rc_11 (CH_11),
#if CONFIG_HAL_BOARD == HAL_BOARD_PX4 || CONFIG_HAL_BOARD == HAL_BOARD_VRBRAIN
rc_12 (CH_12),
rc_13 (CH_13),
rc_14 (CH_14),
#endif
// PID controller initial P initial I initial D initial imax
//----------------------------------------------------------------------------------------------------------
pid_rate_roll (RATE_ROLL_P, RATE_ROLL_I, RATE_ROLL_D, RATE_ROLL_IMAX),
pid_rate_pitch (RATE_PITCH_P, RATE_PITCH_I, RATE_PITCH_D, RATE_PITCH_IMAX),
pid_rate_yaw (RATE_YAW_P, RATE_YAW_I, RATE_YAW_D, RATE_YAW_IMAX),
pid_loiter_rate_lat (LOITER_RATE_P, LOITER_RATE_I, LOITER_RATE_D, LOITER_RATE_IMAX),
pid_loiter_rate_lon (LOITER_RATE_P, LOITER_RATE_I, LOITER_RATE_D, LOITER_RATE_IMAX),
p_throttle_rate (THROTTLE_RATE_P),
pid_throttle_accel (THROTTLE_ACCEL_P, THROTTLE_ACCEL_I, THROTTLE_ACCEL_D, THROTTLE_ACCEL_IMAX),
// P controller initial P
//----------------------------------------------------------------------
p_loiter_pos (LOITER_POS_P),
p_stabilize_roll (STABILIZE_ROLL_P),
p_stabilize_pitch (STABILIZE_PITCH_P),
p_stabilize_yaw (STABILIZE_YAW_P),
p_alt_hold (ALT_HOLD_P)
{
}
};
extern const AP_Param::Info var_info[];
#endif // PARAMETERS_H