mirror of https://github.com/ArduPilot/ardupilot
87 lines
2.6 KiB
Plaintext
87 lines
2.6 KiB
Plaintext
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
// filter altitude from the barometer with a low pass filter
|
|
static LowPassFilterInt32 altitude_filter;
|
|
|
|
|
|
static void init_barometer(void)
|
|
{
|
|
gcs_send_text_P(SEVERITY_LOW, PSTR("Calibrating barometer"));
|
|
barometer.calibrate(mavlink_delay);
|
|
|
|
// filter at 100ms sampling, with 0.7Hz cutoff frequency
|
|
altitude_filter.set_cutoff_frequency(0.1, 0.7);
|
|
|
|
ahrs.set_barometer(&barometer);
|
|
gcs_send_text_P(SEVERITY_LOW, PSTR("barometer calibration complete"));
|
|
}
|
|
|
|
// read the barometer and return the updated altitude in centimeters
|
|
// above the calibration altitude
|
|
static int32_t read_barometer(void)
|
|
{
|
|
barometer.read();
|
|
return altitude_filter.apply(barometer.get_altitude() * 100.0);
|
|
}
|
|
|
|
// in M/S * 100
|
|
static void read_airspeed(void)
|
|
{
|
|
airspeed.read();
|
|
calc_airspeed_errors();
|
|
}
|
|
|
|
static void zero_airspeed(void)
|
|
{
|
|
airspeed.calibrate(mavlink_delay);
|
|
gcs_send_text_P(SEVERITY_LOW,PSTR("zero airspeed calibrated"));
|
|
}
|
|
|
|
static void read_battery(void)
|
|
{
|
|
if(g.battery_monitoring == 0) {
|
|
battery_voltage1 = 0;
|
|
return;
|
|
}
|
|
|
|
if(g.battery_monitoring == 3 || g.battery_monitoring == 4) {
|
|
static AP_AnalogSource_Arduino batt_volt_pin(g.battery_volt_pin);
|
|
// this copes with changing the pin at runtime
|
|
batt_volt_pin.set_pin(g.battery_volt_pin);
|
|
battery_voltage1 = BATTERY_VOLTAGE(batt_volt_pin.read_average());
|
|
}
|
|
if(g.battery_monitoring == 4) {
|
|
static AP_AnalogSource_Arduino batt_curr_pin(g.battery_curr_pin);
|
|
// this copes with changing the pin at runtime
|
|
batt_curr_pin.set_pin(g.battery_curr_pin);
|
|
current_amps1 = CURRENT_AMPS(batt_curr_pin.read_average());
|
|
current_total1 += current_amps1 * (float)delta_ms_medium_loop * 0.0002778; // .0002778 is 1/3600 (conversion to hours)
|
|
}
|
|
|
|
#if BATTERY_EVENT == ENABLED
|
|
if(battery_voltage1 < LOW_VOLTAGE) low_battery_event();
|
|
if(g.battery_monitoring == 4 && current_total1 > g.pack_capacity) low_battery_event();
|
|
#endif
|
|
}
|
|
|
|
|
|
// read the receiver RSSI as an 8 bit number for MAVLink
|
|
// RC_CHANNELS_SCALED message
|
|
void read_receiver_rssi(void)
|
|
{
|
|
RSSI_pin.set_pin(g.rssi_pin);
|
|
float ret = RSSI_pin.read();
|
|
receiver_rssi = constrain(ret, 0, 255);
|
|
}
|
|
|
|
|
|
/*
|
|
return current_loc.alt adjusted for ALT_OFFSET
|
|
This is useful during long flights to account for barometer changes
|
|
from the GCS, or to adjust the flying height of a long mission
|
|
*/
|
|
static int32_t adjusted_altitude_cm(void)
|
|
{
|
|
return current_loc.alt - (g.alt_offset*100);
|
|
}
|