mirror of https://github.com/ArduPilot/ardupilot
231 lines
5.4 KiB
Plaintext
231 lines
5.4 KiB
Plaintext
# LUMINOUS BEE 5.1
|
|
# hw definition file for processing by chibios_hwdef.py
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 1029
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# with 2M flash we can afford to optimize for speed
|
|
env OPTIMIZE -O2
|
|
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
# only one I2C bus
|
|
I2C_ORDER I2C1
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 USART1 UART7
|
|
|
|
# UART4 is GPS
|
|
PA0 UART4_TX UART4
|
|
PA1 UART4_RX UART4
|
|
|
|
# Battery & current control
|
|
PA2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
PA4 VDD_5V_SENS ADC1 SCALE(2)
|
|
|
|
# SPI1 is sensors bus
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
# This is the pin that senses USB being connected. It is an input pin
|
|
# setup as OPENDRAIN.
|
|
PA9 VBUS INPUT #OPENDRAIN
|
|
|
|
# Now we define the pins that USB is connected on.
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# These are the pins for SWD debugging with a STlinkv2 or black-magic probe.
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# PWM output for buzzer
|
|
PA15 TIM2_CH1 TIM2 GPIO(77) ALARM
|
|
|
|
PB2 BOOT1 INPUT
|
|
#PB5 VDD_BRICK_VALID INPUT
|
|
PB5 VDD_BRICK_VALID INPUT PULLDOWN
|
|
|
|
# USART1 TX now as led strip control
|
|
PB6 TIM4_CH1 TIM4 PWM(7) GPIO(56) # PB6
|
|
# PB6 USART1_TX USART1
|
|
PB7 USART1_RX USART1
|
|
|
|
|
|
# UWB DW1000
|
|
PB4 UWB_CS CS
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# SPI2 is FRAM
|
|
PB10 SPI2_SCK SPI2
|
|
PB12 CAN2_RX CAN2
|
|
PB13 CAN2_TX CAN2 # this is SPI2_SCK on beta board
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
#PC0 VBUS_VALID INPUT
|
|
PC0 VBUS_VALID INPUT PULLDOWN
|
|
|
|
#BMI088 CS
|
|
PC2 BMI088_ACCEL_CS CS
|
|
PC15 BMI088_GYRO_CS CS
|
|
|
|
PC3 LED_SAFETY OUTPUT
|
|
PC4 SAFETY_IN INPUT PULLDOWN
|
|
PC5 VDD_PERIPH_EN OUTPUT HIGH
|
|
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW # also USART6_RX for serial RC
|
|
|
|
# Now setup the pins for the microSD card, if available.
|
|
PC8 SDMMC1_D0 SDMMC1
|
|
PC9 SDMMC1_D1 SDMMC1
|
|
PC10 SDMMC1_D2 SDMMC1
|
|
PC11 SDMMC1_D3 SDMMC1
|
|
PC12 SDMMC1_CK SDMMC1
|
|
PD2 SDMMC1_CMD SDMMC1
|
|
|
|
|
|
PC13 SBUS_INV OUTPUT
|
|
|
|
|
|
PD0 CAN1_RX CAN1
|
|
PD1 CAN1_TX CAN1
|
|
|
|
# USART2 serial2 telem1
|
|
|
|
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
|
|
PD7 BARO_CS CS
|
|
|
|
|
|
# USART3 serial3 telem2
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
PD11 USART3_CTS USART3
|
|
PD12 USART3_RTS USART3
|
|
|
|
# The CS pin for FRAM (ramtron). This one is marked as using
|
|
# SPEED_VERYLOW, which matches the HAL_PX4 setup.
|
|
PD10 FRAM_CS CS SPEED_VERYLOW
|
|
|
|
|
|
PD15 20608_DRDY INPUT # IMU Luminous Bee
|
|
# UART8 serial4 FrSky
|
|
PE0 UART8_RX UART8
|
|
PE1 UART8_TX UART8
|
|
|
|
|
|
|
|
#set up SPI bus4 for UWB
|
|
PE2 SPI4_SCK SPI4
|
|
PE5 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
|
|
PE3 VDD_SENSORS_EN OUTPUT HIGH
|
|
PE4 SPEKTRUM_PWR OUTPUT HIGH
|
|
|
|
# UART7 is debug
|
|
PE7 UART7_RX UART7 NODMA
|
|
PE8 UART7_TX UART7 NODMA
|
|
|
|
PE11 TIM1_CH2 TIM1 PWM(1) GPIO(50) #52
|
|
PE14 TIM1_CH4 TIM1 PWM(2) GPIO(51) #50
|
|
PE9 TIM1_CH1 TIM1 PWM(3) GPIO(52) #53
|
|
PE13 TIM1_CH3 TIM1 PWM(4) GPIO(53) #51
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
|
|
|
|
PE12 MAG_DRDY INPUT
|
|
PE15 MAG_CS CS
|
|
|
|
# SPI device table. The DEVID values are chosen to match the PX4 port
|
|
# of ArduPilot so users don't need to re-do their accel and compass calibrations
|
|
# when moving to ChibiOS
|
|
# SPIDEV ms5611_int SPI2 DEVID3 BARO_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV dps310 SPI2 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
|
|
#SPIDEV icm20608 SPI1 DEVID6 20608_CS MODE3 2*MHZ 8*MHZ
|
|
SPIDEV hmc5843 SPI1 DEVID5 MAG_CS MODE3 11*MHZ 11*MHZ
|
|
SPIDEV bmi088_g SPI1 DEVID1 BMI088_GYRO_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV bmi088_a SPI1 DEVID2 BMI088_ACCEL_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
SPIDEV dwm1000 SPI4 DEVID5 UWB_CS MODE0 3*MHZ 20*MHZ
|
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
# enable RAMTROM parameter storage
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# fallback to flash is no FRAM fitted
|
|
#define STORAGE_FLASH_PAGE 22
|
|
|
|
# Enable FAT filesystem support (needs a microSD defined via SDMMC).
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# pixracer has 3 LEDs, Red, Green, Blue
|
|
define HAL_HAVE_PIXRACER_LED
|
|
|
|
define HAL_GPIO_LED_ON 0
|
|
define HAL_GPIO_LED_OFF 1
|
|
|
|
# LED setup for PixracerLED driver
|
|
PB11 LED_RED OUTPUT GPIO(0)
|
|
PB1 LED_GREEN OUTPUT GPIO(1)
|
|
PB3 LED_BLUE OUTPUT GPIO(2)
|
|
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
define HAL_GPIO_B_LED_PIN 1
|
|
define HAL_GPIO_C_LED_PIN 2
|
|
|
|
# battery setup
|
|
define HAL_BATT_VOLT_PIN 14
|
|
define HAL_BATT_CURR_PIN 15
|
|
define HAL_BATT_VOLT_SCALE 10.1
|
|
define HAL_BATT_CURR_SCALE 17.0
|
|
|
|
# setup serial port defaults for ESP8266
|
|
define HAL_SERIAL5_PROTOCOL SerialProtocol_MAVLink
|
|
define HAL_SERIAL5_BAUD 921600
|
|
|
|
# 6 PWM available by default
|
|
define BOARD_PWM_COUNT_DEFAULT 6
|
|
|
|
|
|
# two IMUs
|
|
#IMU Invensense SPI:icm20608 ROTATION_YAW_180
|
|
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_ROLL_180_YAW_90
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
|
|
|
# 2 compasses. R15 has LIS3MDL instead of HMC5843
|
|
COMPASS HMC5843 SPI:hmc5843 false ROTATION_PITCH_180
|
|
#COMPASS LIS3MDL SPI:lis3mdl false ROTATION_NONE
|
|
#COMPASS AK8963:probe_mpu9250 0 ROTATION_ROLL_180_YAW_90
|
|
|
|
# also probe all types of external I2C compasses
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
# TWO barometer
|
|
BARO DPS280 SPI:dps310
|