mirror of https://github.com/ArduPilot/ardupilot
122 lines
2.5 KiB
Plaintext
122 lines
2.5 KiB
Plaintext
/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
static void read_control_switch()
|
|
{
|
|
static bool switch_debouncer = false;
|
|
byte switchPosition = readSwitch();
|
|
|
|
if (oldSwitchPosition != switchPosition){
|
|
if(switch_debouncer){
|
|
// remember the prev location for GS
|
|
prev_WP = current_loc;
|
|
oldSwitchPosition = switchPosition;
|
|
switch_debouncer = false;
|
|
|
|
set_mode(flight_modes[switchPosition]);
|
|
}else{
|
|
switch_debouncer = true;
|
|
}
|
|
}
|
|
}
|
|
|
|
static byte readSwitch(void){
|
|
int pulsewidth = g.rc_5.radio_in; // default for Arducopter
|
|
|
|
if (pulsewidth > 1230 && pulsewidth <= 1360) return 1;
|
|
if (pulsewidth > 1360 && pulsewidth <= 1490) return 2;
|
|
if (pulsewidth > 1490 && pulsewidth <= 1620) return 3;
|
|
if (pulsewidth > 1620 && pulsewidth <= 1749) return 4; // Software Manual
|
|
if (pulsewidth >= 1750) return 5; // Hardware Manual
|
|
return 0;
|
|
}
|
|
|
|
static void reset_control_switch()
|
|
{
|
|
oldSwitchPosition = -1;
|
|
read_control_switch();
|
|
}
|
|
|
|
static boolean trim_flag;
|
|
|
|
// read at 10 hz
|
|
// set this to your trainer switch
|
|
static void read_trim_switch()
|
|
{
|
|
#if CH7_OPTION == DO_FLIP
|
|
if (g.rc_7.control_in > 800 && g.rc_3.control_in != 0){
|
|
do_flip = true;
|
|
}
|
|
|
|
#elif CH7_OPTION == DO_SET_HOVER
|
|
// switch is engaged
|
|
if (g.rc_7.control_in > 800){
|
|
trim_flag = true;
|
|
|
|
}else{ // switch is disengaged
|
|
|
|
if(trim_flag){
|
|
|
|
// set the throttle nominal
|
|
if(g.rc_3.control_in > 150){
|
|
g.throttle_cruise.set_and_save(g.rc_3.control_in);
|
|
//Serial.printf("tnom %d\n", g.throttle_cruise.get());
|
|
}
|
|
trim_flag = false;
|
|
|
|
}
|
|
}
|
|
#endif
|
|
}
|
|
|
|
static void auto_trim()
|
|
{
|
|
if(auto_level_counter > 0){
|
|
//g.rc_1.dead_zone = 60; // 60 = .6 degrees
|
|
//g.rc_2.dead_zone = 60;
|
|
|
|
auto_level_counter--;
|
|
trim_accel();
|
|
led_mode = AUTO_TRIM_LEDS;
|
|
|
|
if(auto_level_counter == 1){
|
|
//g.rc_1.dead_zone = 0; // 60 = .6 degrees
|
|
//g.rc_2.dead_zone = 0;
|
|
led_mode = NORMAL_LEDS;
|
|
clear_leds();
|
|
imu.save();
|
|
Serial.println("Done");
|
|
auto_level_counter = 0;
|
|
}
|
|
}
|
|
}
|
|
|
|
|
|
|
|
static void trim_accel()
|
|
{
|
|
g.pi_stabilize_roll.reset_I();
|
|
g.pi_stabilize_pitch.reset_I();
|
|
|
|
if(g.rc_1.control_in > 0){
|
|
imu.ay(imu.ay() + 1);
|
|
}else if (g.rc_1.control_in < 0){
|
|
imu.ay(imu.ay() - 1);
|
|
}
|
|
|
|
if(g.rc_2.control_in > 0){
|
|
imu.ax(imu.ax() + 1);
|
|
}else if (g.rc_2.control_in < 0){
|
|
imu.ax(imu.ax() - 1);
|
|
}
|
|
|
|
/*
|
|
Serial.printf_P(PSTR("r:%ld p:%ld ax:%f, ay:%f, az:%f\n"),
|
|
dcm.roll_sensor,
|
|
dcm.pitch_sensor,
|
|
(float)imu.ax(),
|
|
(float)imu.ay(),
|
|
(float)imu.az());
|
|
//*/
|
|
}
|
|
|