mirror of https://github.com/ArduPilot/ardupilot
117 lines
3.0 KiB
C
117 lines
3.0 KiB
C
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
|
|
|
|
// Example config file. Take a look at config.h. Any term define there can be overridden by defining it here.
|
|
|
|
//#define CONFIG_APM_HARDWARE APM_HARDWARE_APM2
|
|
//#define APM2_BETA_HARDWARE
|
|
|
|
// GPS is auto-selected
|
|
|
|
//#define MAG_ORIENTATION AP_COMPASS_COMPONENTS_DOWN_PINS_FORWARD
|
|
//#define HIL_MODE HIL_MODE_ATTITUDE
|
|
//#define DMP_ENABLED ENABLED
|
|
|
|
//#define FRAME_CONFIG QUAD_FRAME
|
|
/*
|
|
options:
|
|
QUAD_FRAME
|
|
TRI_FRAME
|
|
HEXA_FRAME
|
|
Y6_FRAME
|
|
OCTA_FRAME
|
|
OCTA_QUAD_FRAME
|
|
HELI_FRAME
|
|
*/
|
|
|
|
//#define FRAME_ORIENTATION X_FRAME
|
|
/*
|
|
PLUS_FRAME
|
|
X_FRAME
|
|
V_FRAME
|
|
*/
|
|
|
|
//#define CH7_OPTION CH7_SAVE_WP
|
|
/*
|
|
CH7_DO_NOTHING
|
|
CH7_SET_HOVER
|
|
CH7_FLIP
|
|
CH7_SIMPLE_MODE
|
|
CH7_RTL
|
|
CH7_AUTO_TRIM
|
|
CH7_ADC_FILTER (experimental)
|
|
CH7_SAVE_WP
|
|
CH7_MULTI_MODE
|
|
*/
|
|
|
|
//#define TOY_EDF ENABLED
|
|
//#define TOY_MIXER TOY_LOOKUP_TABLE
|
|
|
|
|
|
#define ACCEL_ALT_HOLD 0 // disabled by default, work in progress
|
|
#define INERTIAL_NAV DISABLED
|
|
|
|
|
|
#if INERTIAL_NAV == ENABLED
|
|
#define ALT_HOLD_P 3
|
|
#define ALT_HOLD_I 0
|
|
#define ALT_HOLD_IMAX 300
|
|
|
|
// RATE control
|
|
#define THROTTLE_P 5 //
|
|
#define THROTTLE_I 0.4 //
|
|
#define THROTTLE_D 0.0 //
|
|
|
|
#define LOITER_P 0.50
|
|
#define LOITER_I 0.0
|
|
#define LOITER_RATE_P 5 //
|
|
#define LOITER_RATE_I 0.1 // Wind control
|
|
#define LOITER_RATE_D 0.0 // try 2 or 3 for LOITER_RATE 1
|
|
#endif
|
|
|
|
|
|
//#define RATE_ROLL_I 0.18
|
|
//#define RATE_PITCH_I 0.18
|
|
//#define MOTORS_JD880
|
|
//#define MOTORS_JD850
|
|
|
|
|
|
// agmatthews USERHOOKS
|
|
// the choice of function names is up to the user and does not have to match these
|
|
// uncomment these hooks and ensure there is a matching function on your "UserCode.pde" file
|
|
//#define USERHOOK_FASTLOOP userhook_FastLoop();
|
|
#define USERHOOK_50HZLOOP userhook_50Hz();
|
|
//#define USERHOOK_MEDIUMLOOP userhook_MediumLoop();
|
|
//#define USERHOOK_SLOWLOOP userhook_SlowLoop();
|
|
//#define USERHOOK_SUPERSLOWLOOP userhook_SuperSlowLoop();
|
|
#define USERHOOK_INIT userhook_init();
|
|
|
|
// the choice of included variables file (*.h) is up to the user and does not have to match this one
|
|
// Ensure the defined file exists and is in the arducopter directory
|
|
#define USERHOOK_VARIABLES "UserVariables.h"
|
|
|
|
// to enable, set to 1
|
|
// to disable, set to 0
|
|
#define AUTO_THROTTLE_HOLD 1
|
|
|
|
//#define LOGGING_ENABLED DISABLED
|
|
|
|
|
|
// Custom channel config - Expert Use Only.
|
|
// this for defining your own MOT_n to CH_n mapping.
|
|
// Overrides defaults (for APM1 or APM2) found in config_channels.h
|
|
// MOT_n variables are used by the Frame mixing code. You must define
|
|
// MOT_1 through MOT_m where m is the number of motors on your frame.
|
|
// CH_n variables are used for RC output. These can be CH_1 through CH_8,
|
|
// and CH_10 or CH_12.
|
|
// Sample channel config. Must define all MOT_ channels used by
|
|
// your FRAME_TYPE.
|
|
// #define CONFIG_CHANNELS CHANNEL_CONFIG_CUSTOM
|
|
// #define MOT_1 CH_6
|
|
// #define MOT_2 CH_3
|
|
// #define MOT_3 CH_2
|
|
// #define MOT_4 CH_5
|
|
// #define MOT_5 CH_1
|
|
// #define MOT_6 CH_4
|
|
// #define MOT_7 CH_7
|
|
// #define MOT_8 CH_8
|