ardupilot/ArduCopter/mode_flip.cpp

220 lines
8.2 KiB
C++

#include "Copter.h"
#if MODE_FLIP_ENABLED == ENABLED
/*
* Init and run calls for flip flight mode
* original implementation in 2010 by Jose Julio
* Adapted and updated for AC2 in 2011 by Jason Short
*
* Controls:
* RC7_OPTION - RC12_OPTION parameter must be set to "Flip" (AUXSW_FLIP) which is "2"
* Pilot switches to Stabilize, Acro or AltHold flight mode and puts ch7/ch8 switch to ON position
* Vehicle will Roll right by default but if roll or pitch stick is held slightly left, forward or back it will flip in that direction
* Vehicle should complete the roll within 2.5sec and will then return to the original flight mode it was in before flip was triggered
* Pilot may manually exit flip by switching off ch7/ch8 or by moving roll stick to >40deg left or right
*
* State machine approach:
* Flip_Start (while copter is leaning <45deg) : roll right at 400deg/sec, increase throttle
* Flip_Roll (while copter is between +45deg ~ -90) : roll right at 400deg/sec, reduce throttle
* Flip_Recover (while copter is between -90deg and original target angle) : use earth frame angle controller to return vehicle to original attitude
*/
#define FLIP_THR_INC 0.20f // throttle increase during Flip_Start stage (under 45deg lean angle)
#define FLIP_THR_DEC 0.24f // throttle decrease during Flip_Roll stage (between 45deg ~ -90deg roll)
#define FLIP_ROTATION_RATE 40000 // rotation rate request in centi-degrees / sec (i.e. 400 deg/sec)
#define FLIP_TIMEOUT_MS 2500 // timeout after 2.5sec. Vehicle will switch back to original flight mode
#define FLIP_RECOVERY_ANGLE 500 // consider successful recovery when roll is back within 5 degrees of original
#define FLIP_ROLL_RIGHT 1 // used to set flip_dir
#define FLIP_ROLL_LEFT -1 // used to set flip_dir
#define FLIP_PITCH_BACK 1 // used to set flip_dir
#define FLIP_PITCH_FORWARD -1 // used to set flip_dir
// flip_init - initialise flip controller
bool Copter::ModeFlip::init(bool ignore_checks)
{
// only allow flip from ACRO, Stabilize, AltHold or Drift flight modes
if (copter.control_mode != ACRO &&
copter.control_mode != STABILIZE &&
copter.control_mode != ALT_HOLD &&
copter.control_mode != FLOWHOLD) {
return false;
}
// if in acro or stabilize ensure throttle is above zero
if (ap.throttle_zero && (copter.control_mode == ACRO || copter.control_mode == STABILIZE)) {
return false;
}
// ensure roll input is less than 40deg
if (abs(channel_roll->get_control_in()) >= 4000) {
return false;
}
// only allow flip when flying
if (!motors->armed() || ap.land_complete) {
return false;
}
// capture original flight mode so that we can return to it after completion
orig_control_mode = copter.control_mode;
// initialise state
_state = Flip_Start;
start_time_ms = millis();
roll_dir = pitch_dir = 0;
// choose direction based on pilot's roll and pitch sticks
if (channel_pitch->get_control_in() > 300) {
pitch_dir = FLIP_PITCH_BACK;
} else if (channel_pitch->get_control_in() < -300) {
pitch_dir = FLIP_PITCH_FORWARD;
} else if (channel_roll->get_control_in() >= 0) {
roll_dir = FLIP_ROLL_RIGHT;
} else {
roll_dir = FLIP_ROLL_LEFT;
}
// log start of flip
Log_Write_Event(DATA_FLIP_START);
// capture current attitude which will be used during the Flip_Recovery stage
const float angle_max = copter.aparm.angle_max;
orig_attitude.x = constrain_float(ahrs.roll_sensor, -angle_max, angle_max);
orig_attitude.y = constrain_float(ahrs.pitch_sensor, -angle_max, angle_max);
orig_attitude.z = ahrs.yaw_sensor;
return true;
}
// run - runs the flip controller
// should be called at 100hz or more
void Copter::ModeFlip::run()
{
// if pilot inputs roll > 40deg or timeout occurs abandon flip
if (!motors->armed() || (abs(channel_roll->get_control_in()) >= 4000) || (abs(channel_pitch->get_control_in()) >= 4000) || ((millis() - start_time_ms) > FLIP_TIMEOUT_MS)) {
_state = Flip_Abandon;
}
// get pilot's desired throttle
float throttle_out = get_pilot_desired_throttle(channel_throttle->get_control_in());
// get corrected angle based on direction and axis of rotation
// we flip the sign of flip_angle to minimize the code repetition
int32_t flip_angle;
if (roll_dir != 0) {
flip_angle = ahrs.roll_sensor * roll_dir;
} else {
flip_angle = ahrs.pitch_sensor * pitch_dir;
}
// state machine
switch (_state) {
case Flip_Start:
// under 45 degrees request 400deg/sec roll or pitch
attitude_control->input_rate_bf_roll_pitch_yaw(FLIP_ROTATION_RATE * roll_dir, FLIP_ROTATION_RATE * pitch_dir, 0.0);
// increase throttle
throttle_out += FLIP_THR_INC;
// beyond 45deg lean angle move to next stage
if (flip_angle >= 4500) {
if (roll_dir != 0) {
// we are rolling
_state = Flip_Roll;
} else {
// we are pitching
_state = Flip_Pitch_A;
}
}
break;
case Flip_Roll:
// between 45deg ~ -90deg request 400deg/sec roll
attitude_control->input_rate_bf_roll_pitch_yaw(FLIP_ROTATION_RATE * roll_dir, 0.0, 0.0);
// decrease throttle
throttle_out = MAX(throttle_out - FLIP_THR_DEC, 0.0f);
// beyond -90deg move on to recovery
if ((flip_angle < 4500) && (flip_angle > -9000)) {
_state = Flip_Recover;
}
break;
case Flip_Pitch_A:
// between 45deg ~ -90deg request 400deg/sec pitch
attitude_control->input_rate_bf_roll_pitch_yaw(0.0f, FLIP_ROTATION_RATE * pitch_dir, 0.0);
// decrease throttle
throttle_out = MAX(throttle_out - FLIP_THR_DEC, 0.0f);
// check roll for inversion
if ((labs(ahrs.roll_sensor) > 9000) && (flip_angle > 4500)) {
_state = Flip_Pitch_B;
}
break;
case Flip_Pitch_B:
// between 45deg ~ -90deg request 400deg/sec pitch
attitude_control->input_rate_bf_roll_pitch_yaw(0.0, FLIP_ROTATION_RATE * pitch_dir, 0.0);
// decrease throttle
throttle_out = MAX(throttle_out - FLIP_THR_DEC, 0.0f);
// check roll for inversion
if ((labs(ahrs.roll_sensor) < 9000) && (flip_angle > -4500)) {
_state = Flip_Recover;
}
break;
case Flip_Recover: {
// use originally captured earth-frame angle targets to recover
attitude_control->input_euler_angle_roll_pitch_yaw(orig_attitude.x, orig_attitude.y, orig_attitude.z, false);
// increase throttle to gain any lost altitude
throttle_out += FLIP_THR_INC;
float recovery_angle;
if (roll_dir != 0) {
// we are rolling
recovery_angle = fabsf(orig_attitude.x - (float)ahrs.roll_sensor);
} else {
// we are pitching
recovery_angle = fabsf(orig_attitude.y - (float)ahrs.pitch_sensor);
}
// check for successful recovery
if (fabsf(recovery_angle) <= FLIP_RECOVERY_ANGLE) {
// restore original flight mode
if (!copter.set_mode(orig_control_mode, MODE_REASON_FLIP_COMPLETE)) {
// this should never happen but just in case
copter.set_mode(STABILIZE, MODE_REASON_UNKNOWN);
}
// log successful completion
Log_Write_Event(DATA_FLIP_END);
}
break;
}
case Flip_Abandon:
// restore original flight mode
if (!copter.set_mode(orig_control_mode, MODE_REASON_FLIP_COMPLETE)) {
// this should never happen but just in case
copter.set_mode(STABILIZE, MODE_REASON_UNKNOWN);
}
// log abandoning flip
copter.Log_Write_Error(ERROR_SUBSYSTEM_FLIP,ERROR_CODE_FLIP_ABANDONED);
break;
}
// set motors to full range
motors->set_desired_spool_state(AP_Motors::DESIRED_THROTTLE_UNLIMITED);
// output pilot's throttle without angle boost
attitude_control->set_throttle_out(throttle_out, false, g.throttle_filt);
}
#endif