ardupilot/libraries/AP_IOMCU/iofirmware/rc.cpp

185 lines
4.9 KiB
C++

/*
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/*
SBUS output support
*/
#include "ch.h"
#include "hal.h"
#include "iofirmware.h"
#include "rc.h"
#include <AP_SBusOut/AP_SBusOut.h>
extern const AP_HAL::HAL& hal;
// usart3 is for SBUS input and output
static const SerialConfig uart3_cfg = {
100000, // speed
USART_CR1_PCE | USART_CR1_M, // cr1, enable even parity
USART_CR2_STOP_1, // cr2, two stop bits
0, // cr3
nullptr, // irq_cb
nullptr, // ctx
};
// listen for parity errors on sd3 input
static event_listener_t sd3_listener;
void sbus_out_write(uint16_t *channels, uint8_t nchannels)
{
uint8_t buffer[25];
AP_SBusOut::sbus_format_frame(channels, nchannels, buffer);
chnWrite(&SD3, buffer, sizeof(buffer));
}
// usart1 is for DSM input and (optionally) debug to FMU
static const SerialConfig uart1_cfg = {
115200, // speed
0, // cr1
0, // cr2
0, // cr3
nullptr, // irq_cb
nullptr, // ctx
};
/*
init rcin on DSM USART1
*/
void AP_IOMCU_FW::rcin_serial_init(void)
{
sdStart(&SD1, &uart1_cfg);
sdStart(&SD3, &uart3_cfg);
chEvtRegisterMaskWithFlags(chnGetEventSource(&SD3),
&sd3_listener,
EVENT_MASK(1),
SD_PARITY_ERROR);
rcprotocol = AP_RCProtocol::get_instance();
// disable input for SBUS with pulses, we will use the UART for
// SBUS.
rcprotocol->disable_for_pulses(AP_RCProtocol::SBUS);
rcprotocol->disable_for_pulses(AP_RCProtocol::SBUS_NI);
}
static struct {
uint32_t num_dsm_bytes;
uint32_t num_sbus_bytes;
uint32_t num_sbus_errors;
eventflags_t sbus_error;
} rc_stats;
/*
check for data on DSM RX uart
*/
void AP_IOMCU_FW::rcin_serial_update(void)
{
uint8_t b[16];
uint32_t n;
// read from DSM port
if ((n = chnReadTimeout(&SD1, b, sizeof(b), TIME_IMMEDIATE)) > 0) {
n = MIN(n, sizeof(b));
rc_stats.num_dsm_bytes += n;
for (uint8_t i=0; i<n; i++) {
rcprotocol->process_byte(b[i], 115200);
}
//BLUE_TOGGLE();
}
// read from SBUS port
if ((n = chnReadTimeout(&SD3, b, sizeof(b), TIME_IMMEDIATE)) > 0) {
eventflags_t flags;
if ((flags = chEvtGetAndClearFlags(&sd3_listener)) & SD_PARITY_ERROR) {
rc_stats.sbus_error = flags;
rc_stats.num_sbus_errors++;
} else {
n = MIN(n, sizeof(b));
rc_stats.num_sbus_bytes += n;
for (uint8_t i=0; i<n; i++) {
rcprotocol->process_byte(b[i], 100000);
}
}
}
}
/*
sleep for 1ms using a busy loop
*/
static void delay_one_ms(uint32_t &now)
{
while (now == AP_HAL::millis()) ;
now = AP_HAL::millis();
}
/*
perform a DSM bind operation
*/
void AP_IOMCU_FW::dsm_bind_step(void)
{
uint32_t now = last_ms;
switch (dsm_bind_state) {
case 1:
palSetLineMode(HAL_GPIO_PIN_SPEKTRUM_PWR_EN, PAL_MODE_OUTPUT_PUSHPULL);
SPEKTRUM_POWER(0);
palSetLineMode(HAL_GPIO_PIN_SPEKTRUM_OUT, PAL_MODE_OUTPUT_PUSHPULL);
SPEKTRUM_SET(1);
dsm_bind_state = 2;
last_dsm_bind_ms = now;
break;
case 2:
if (now - last_dsm_bind_ms >= 500) {
SPEKTRUM_POWER(1);
dsm_bind_state = 3;
last_dsm_bind_ms = now;
}
break;
case 3: {
if (now - last_dsm_bind_ms >= 72) {
// 9 pulses works with all satellite receivers, and supports the highest
// available protocol
delay_one_ms(now);
const uint8_t num_pulses = 9;
for (uint8_t i=0; i<num_pulses; i++) {
// the delay should be 120us, but we are running our
// clock at 1kHz, and 1ms works fine
delay_one_ms(now);
SPEKTRUM_SET(0);
delay_one_ms(now);
SPEKTRUM_SET(1);
}
last_dsm_bind_ms = now;
dsm_bind_state = 4;
}
break;
}
case 4:
if (now - last_dsm_bind_ms >= 50) {
// set back as input pin
palSetLineMode(HAL_GPIO_PIN_SPEKTRUM_OUT, PAL_MODE_INPUT);
dsm_bind_state = 0;
}
break;
default:
dsm_bind_state = 0;
break;
}
}