mirror of https://github.com/ArduPilot/ardupilot
169 lines
3.5 KiB
Plaintext
169 lines
3.5 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for the MicoAir743 hardware
|
|
|
|
# MCU class and specific type
|
|
MCU STM32H7xx STM32H743xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID AP_HW_MicoAir743
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
# ChibiOS system timer
|
|
STM32_ST_USE_TIMER 12
|
|
define CH_CFG_ST_RESOLUTION 16
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
FLASH_RESERVE_START_KB 128
|
|
|
|
define HAL_STORAGE_SIZE 32768
|
|
STORAGE_FLASH_PAGE 14
|
|
|
|
# default to all pins low to avoid ESD issues
|
|
DEFAULTGPIO OUTPUT LOW PULLDOWN
|
|
|
|
# order of UARTs (and USB)
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 USART6 UART7 UART8
|
|
|
|
# USB
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
# USART1 - TELEM1
|
|
PA9 USART1_TX USART1
|
|
PA10 USART1_RX USART1
|
|
|
|
# USART2 - DJIO3
|
|
PA2 USART2_TX USART2
|
|
PA3 USART2_RX USART2
|
|
|
|
# USART3 - GPS
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
|
|
# UART4 - TELEM2
|
|
PA0 UART4_TX UART4
|
|
PA1 UART4_RX UART4
|
|
|
|
# UART6 - RC_INPUT
|
|
PC6 USART6_TX USART6
|
|
PC7 USART6_RX USART6
|
|
PD0 SBUS_INV OUTPUT LOW
|
|
|
|
# UART7 - ESC
|
|
PE7 UART7_RX UART7
|
|
|
|
# UART8 - TELEM3
|
|
PE1 UART8_TX UART8
|
|
PE0 UART8_RX UART8
|
|
|
|
# SWD
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# CAN
|
|
PB8 CAN1_RX CAN1
|
|
PB9 CAN1_TX CAN1
|
|
|
|
# two I2C bus
|
|
I2C_ORDER I2C2 I2C1
|
|
|
|
# I2C1 - CONNECTOR
|
|
PB6 I2C1_SCL I2C1
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
# I2C2 - BARO & MAG
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
|
|
# PWM output pins
|
|
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50) BIDIR
|
|
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52) BIDIR
|
|
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
|
PB1 TIM3_CH4 TIM3 PWM(5) GPIO(54) BIDIR
|
|
PB0 TIM3_CH3 TIM3 PWM(6) GPIO(55)
|
|
PD12 TIM4_CH1 TIM4 PWM(7) GPIO(56) BIDIR
|
|
PD13 TIM4_CH2 TIM4 PWM(8) GPIO(57)
|
|
PD14 TIM4_CH3 TIM4 PWM(9) GPIO(58)
|
|
PD15 TIM4_CH4 TIM4 PWM(10) GPIO(59)
|
|
|
|
# 10 PWM available by default
|
|
define BOARD_PWM_COUNT_DEFAULT 10
|
|
|
|
# LEDs
|
|
PE5 LED_RED OUTPUT LOW GPIO(0)
|
|
PE6 LED_GREEN OUTPUT LOW GPIO(1)
|
|
PE4 LED_BLUE OUTPUT LOW GPIO(2)
|
|
|
|
define AP_NOTIFY_GPIO_LED_RGB_RED_PIN 0
|
|
define AP_NOTIFY_GPIO_LED_RGB_GREEN_PIN 1
|
|
define AP_NOTIFY_GPIO_LED_RGB_BLUE_PIN 2
|
|
|
|
define AP_NOTIFY_GPIO_LED_RGB_ENABLED 1
|
|
|
|
# ADC for Power
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
define HAL_BATT_VOLT_PIN 10
|
|
define HAL_BATT_CURR_PIN 11
|
|
define HAL_BATT_VOLT_SCALE 21.12
|
|
define HAL_BATT_CURR_SCALE 40.2
|
|
|
|
# compass
|
|
define HAL_COMPASS_DISABLE_IST8310_INTERNAL_PROBE
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
COMPASS IST8310 I2C:ALL_EXTERNAL:0x0E true ROTATION_NONE
|
|
COMPASS IST8310 I2C:ALL_INTERNAL:0x0E false ROTATION_YAW_90
|
|
|
|
# barometers
|
|
BARO DPS310 I2C:0:0x76
|
|
|
|
# microSD support
|
|
PC12 SDMMC1_CK SDMMC1
|
|
PD2 SDMMC1_CMD SDMMC1
|
|
PC8 SDMMC1_D0 SDMMC1
|
|
PC9 SDMMC1_D1 SDMMC1
|
|
PC10 SDMMC1_D2 SDMMC1
|
|
PC11 SDMMC1_D3 SDMMC1
|
|
define FATFS_HAL_DEVICE SDCD1
|
|
|
|
# SPI1 - AT7456E
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
PB12 AT7456E_CS CS
|
|
|
|
# SPI2 - IMUs
|
|
PD3 SPI2_SCK SPI2
|
|
PC2 SPI2_MISO SPI2
|
|
PC3 SPI2_MOSI SPI2
|
|
PD5 GYRO_CS CS
|
|
PD4 ACCEL_CS CS
|
|
PA15 BMI270_CS CS
|
|
|
|
# SPI devices
|
|
SPIDEV bmi088_a SPI2 DEVID1 ACCEL_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV bmi088_g SPI2 DEVID2 GYRO_CS MODE3 10*MHZ 10*MHZ
|
|
SPIDEV bmi270 SPI2 DEVID3 BMI270_CS MODE3 1*MHZ 10*MHZ
|
|
SPIDEV osd SPI1 DEVID4 AT7456E_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
# 2 IMUs
|
|
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_ROLL_180_YAW_270
|
|
IMU BMI270 SPI:bmi270 ROTATION_ROLL_180
|
|
|
|
# enable FAT filesystem support (needs a microSD defined via SDMMC)
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
# setup for OSD
|
|
define OSD_ENABLED 1
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
|
|
|
# setup for BF migration
|
|
define HAL_FRAME_TYPE_DEFAULT 12
|
|
|