mirror of https://github.com/ArduPilot/ardupilot
115 lines
2.6 KiB
Plaintext
115 lines
2.6 KiB
Plaintext
# hw definition file for f405 Holybro CAN PMU
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
# bootloader starts firmware at 64k
|
|
FLASH_RESERVE_START_KB 64
|
|
FLASH_SIZE_KB 1024
|
|
|
|
# store parameters in pages 2 and 3
|
|
STORAGE_FLASH_PAGE 2
|
|
define HAL_STORAGE_SIZE 15360
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 5401
|
|
|
|
env AP_PERIPH 1
|
|
|
|
define STM32_ST_USE_TIMER 5
|
|
define CH_CFG_ST_RESOLUTION 32
|
|
|
|
# enable watchdog
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
STDOUT_SERIAL SD3
|
|
STDOUT_BAUDRATE 57600
|
|
|
|
# blue LED0 marked as ACT
|
|
PB0 LED OUTPUT HIGH GPIO(90)
|
|
define AP_NOTIFY_GPIO_LED_1_ENABLED 1
|
|
define AP_NOTIFY_GPIO_LED_1_PIN 90
|
|
|
|
define HAL_NO_GPIO_IRQ
|
|
define SERIAL_BUFFERS_SIZE 512
|
|
define PORT_INT_REQUIRED_STACK 64
|
|
|
|
# debug
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
# avoid timer and RCIN threads to save memory
|
|
define HAL_NO_RCIN_THREAD
|
|
|
|
define HAL_USE_RTC FALSE
|
|
define DISABLE_SERIAL_ESC_COMM TRUE
|
|
|
|
define DMA_RESERVE_SIZE 0
|
|
|
|
define HAL_DEVICE_THREAD_STACK 768
|
|
|
|
# we setup a small defaults.parm
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 256
|
|
|
|
# keep ROMFS uncompressed as we don't have enough RAM
|
|
# to uncompress the bootloader at runtime
|
|
env ROMFS_UNCOMPRESSED True
|
|
|
|
# ---------------------- CAN bus -------------------------
|
|
PA11 CAN1_RX CAN1
|
|
PA12 CAN1_TX CAN1
|
|
PA15 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW
|
|
|
|
# use DNA for node allocation
|
|
|
|
define CAN_APP_NODE_NAME "org.ardupilot.f405_HolybroPMU"
|
|
|
|
|
|
# ---------------------- UARTs ---------------------------
|
|
#
|
|
SERIAL_ORDER USART3
|
|
|
|
# USART3, for debug
|
|
PC10 USART3_TX USART3 SPEED_HIGH NODMA
|
|
PC11 USART3_RX USART3 SPEED_HIGH NODMA
|
|
|
|
# ---------------------- I2Cs ---------------------------
|
|
#
|
|
I2C_ORDER I2C1
|
|
|
|
# I2C2, for TEMP SENSOR
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
# ------------------ BATTERY Monitor -----------------------
|
|
define HAL_PERIPH_ENABLE_BATTERY
|
|
define HAL_PERIPH_ENABLE_DEVICE_TEMPERATURE
|
|
define HAL_USE_ADC TRUE
|
|
define STM32_ADC_USE_ADC1 TRUE
|
|
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
# Set the Default Battery Monitor Type to be Analog I/V
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
|
|
define HAL_BATT_VOLT_PIN 10
|
|
define HAL_BATT_VOLT_SCALE 18.0
|
|
|
|
define HAL_BATT_CURR_PIN 11
|
|
define HAL_BATT_CURR_SCALE 125
|
|
|
|
# ACS772-400U Zero-Current Offset
|
|
define AP_BATT_CURR_AMP_OFFSET_DEFAULT 0.409
|
|
|
|
# ------------------ Temperature Sensor -----------------------
|
|
define AP_TEMPERATURE_SENSOR_ENABLED 1
|
|
define AP_TEMPERATURE_SENSOR_TSYS03_ENABLED 1
|
|
define AP_TEMPERATURE_SENSOR_I2C_ADDR_DEFAULT 64
|
|
define AP_TEMPERATURE_SENSOR_I2C_BUS_DEFAULT 0
|
|
|
|
|
|
|