mirror of https://github.com/ArduPilot/ardupilot
246 lines
4.4 KiB
Plaintext
246 lines
4.4 KiB
Plaintext
# hw definition file for processing by chibios_hwdef.py
|
|
# for ProfiCNC/Hex CUBE RED hardware
|
|
|
|
# MCU class and specific type
|
|
MCU STM32F7xx STM32F767xx
|
|
|
|
# board ID for firmware load
|
|
APJ_BOARD_ID 9
|
|
|
|
# crystal frequency
|
|
OSCILLATOR_HZ 24000000
|
|
|
|
# board voltage
|
|
STM32_VDD 330U
|
|
|
|
# flash size
|
|
FLASH_SIZE_KB 2048
|
|
|
|
# no serial port for stdout, use USB instead
|
|
# STDOUT_SERIAL SD7
|
|
# STDOUT_BAUDRATE 57600
|
|
|
|
# USB setup
|
|
USB_VENDOR 0x2DAE # ONLY FOR USE BY HEX! NOBODY ELSE
|
|
USB_PRODUCT 0x1002
|
|
USB_STRING_MANUFACTURER "Hex Technology Limited"
|
|
USB_STRING_PRODUCT "ProfiCNC CUBE F7 FMU"
|
|
USB_STRING_SERIAL "%SERIAL%"
|
|
|
|
# order of I2C buses
|
|
I2C_ORDER I2C2 I2C1
|
|
|
|
# order of UARTs (and USB)
|
|
UART_ORDER OTG1 UART4 USART2 USART3 UART8 UART7
|
|
|
|
# UART for IOMCU
|
|
IOMCU_UART USART6
|
|
|
|
# UART4 serial GPS
|
|
PA0 UART4_TX UART4
|
|
PA1 UART4_RX UART4
|
|
PA2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
PA4 VDD_5V_SENS ADC1 SCALE(2)
|
|
PA5 SPI1_SCK SPI1
|
|
PA6 SPI1_MISO SPI1
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
PA8 CAN3_RX CAN3
|
|
PA9 VBUS INPUT OPENDRAIN
|
|
#PA10 IO-debug-console
|
|
PA11 OTG_FS_DM OTG1
|
|
PA12 OTG_FS_DP OTG1
|
|
PA13 JTMS-SWDIO SWD
|
|
PA14 JTCK-SWCLK SWD
|
|
PA15 CAN3_TX CAN3
|
|
|
|
|
|
PB0 EXTERN_GPIO1 OUTPUT GPIO(1)
|
|
PB1 EXTERN_GPIO2 OUTPUT GPIO(2)
|
|
PB2 BOOT1 INPUT
|
|
PB3 FMU_SW0 INPUT
|
|
PB4 PWM_VOLT_SELECT OUTPUT LOW
|
|
PB5 SPI6_MOSI SPI6
|
|
PB6 CAN2_TX CAN2
|
|
#PB7
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
PB9 I2C1_SDA I2C1
|
|
PB10 I2C2_SCL I2C2
|
|
PB11 I2C2_SDA I2C2
|
|
PB12 CAN2_RX CAN2
|
|
PB13 SPI2_SCK SPI2
|
|
PB14 SPI2_MISO SPI2
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
|
|
PC0 HW_VERSION_SENSE INPUT
|
|
PC1 HW_REV_SENSE INPUT
|
|
#PC2
|
|
#PC3
|
|
#PC4
|
|
#PC5
|
|
# USART6 to IO
|
|
PC6 USART6_TX USART6
|
|
PC7 USART6_RX USART6
|
|
|
|
PC8 SDMMC_D0 SDMMC1
|
|
PC9 SDMMC_D1 SDMMC1
|
|
PC10 SDMMC_D2 SDMMC1
|
|
PC11 SDMMC_D3 SDMMC1
|
|
PC12 SDMMC_CK SDMMC1
|
|
PD2 SDMMC_CMD SDMMC1
|
|
|
|
PC13 GYRO_EXT_CS CS
|
|
|
|
|
|
PD0 CAN1_RX CAN1
|
|
PD1 CAN1_TX CAN1
|
|
|
|
# USART2 serial2 telem1
|
|
PD3 USART2_CTS USART2
|
|
PD4 USART2_RTS USART2
|
|
PD5 USART2_TX USART2
|
|
PD6 USART2_RX USART2
|
|
PD7 BARO_CS CS
|
|
|
|
# USART3 serial3 telem2
|
|
PD8 USART3_TX USART3
|
|
PD9 USART3_RX USART3
|
|
PD10 FRAM_CS CS
|
|
PD11 USART3_CTS USART3
|
|
PD12 USART3_RTS USART3
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
PD15 MPU_DRDY INPUT
|
|
|
|
|
|
# UART8 serial4 GPS2
|
|
PE0 UART8_RX UART8
|
|
PE1 UART8_TX UART8
|
|
PE2 SPI4_SCK SPI4
|
|
PE3 VDD_3V3_SENSORS_EN OUTPUT HIGH
|
|
PE4 ICM20948_CS CS
|
|
PE5 SPI4_MISO SPI4
|
|
PE6 SPI4_MOSI SPI4
|
|
# UART7 debug console
|
|
PE7 UART7_RX UART7
|
|
|
|
PE8 UART7_TX UART7
|
|
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
|
#PE10
|
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
|
PE12 FMU_LED_AMBER OUTPUT GPIO(0)
|
|
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
|
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
|
|
PE15 VDD_5V_PERIPH_OC INPUT
|
|
|
|
#PF0
|
|
#PF1
|
|
PF2 ICM20649_CS CS
|
|
#PF3 FMU_AUX_POWER ADC1 SCALE(1)
|
|
#PF4 FMU_AUX_ADC2 ADC1 SCALE(1)
|
|
#PF5 PRESSURE_SENS ADC1 SCALE(1)
|
|
#PF6
|
|
#PF7
|
|
|
|
#PF8
|
|
#PF9
|
|
PF10 MS5611_CS CS
|
|
PF11 SPARE_CS CS
|
|
#PF12
|
|
PF13 VDD_5V_HIPOWER_OC INPUT
|
|
#PF14
|
|
#PF15
|
|
|
|
#PG0
|
|
PG1 VDD_BRICK_VALID INPUT
|
|
PG2 VBUS_VALID INPUT
|
|
PG3 VDD_BACKUP_VALID INPUT
|
|
PG4 VDD_5V_PERIPH_EN OUTPUT LOW
|
|
#PG5
|
|
#PG6
|
|
#PG7
|
|
|
|
#PG8 SPI6_CS CS
|
|
#PG9
|
|
#PG10
|
|
#PG11 SPI6_CS2 CS
|
|
PG12 SPI6_MISO SPI6
|
|
PG13 SPI6_SCK SPI6
|
|
#PG14
|
|
#PG15
|
|
|
|
#PH0 OSC_IN 24MHz
|
|
#PH1 OSC_OUT 24MHz
|
|
PH2 HW_VER_DRIVE OUTPUT HIGH
|
|
PH3 HW_REV_DRIVE OUTPUT HIGH
|
|
#PH4
|
|
#PH5
|
|
#PH6
|
|
#PH7
|
|
|
|
#PH8
|
|
PH9 ALARM OUTPUT
|
|
#PH10
|
|
#PH11
|
|
#PH12
|
|
#PH13
|
|
#PH14
|
|
#PH15
|
|
|
|
#PI0
|
|
#PI1
|
|
#PI2
|
|
#PI3
|
|
#PI4
|
|
#PI5 PPM_IN
|
|
#PI6
|
|
#PI7
|
|
|
|
#PI8
|
|
#PI9
|
|
#PI10
|
|
#PI11
|
|
|
|
|
|
# SPI device table. The DEVID values are chosen to match the PX4 port
|
|
# of ArduPilot so users don't need to re-do their accel and compass calibrations
|
|
# when moving to ChibiOS
|
|
|
|
#sensors on Main FMU board
|
|
SPIDEV ms5611 SPI1 DEVID3 MS5611_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV ICM20649 SPI1 DEVID2 ICM20649_CS MODE3 1*MHZ 8*MHZ
|
|
|
|
#Sensors on the isolated IMU Board
|
|
#SPIDEV ICM20602 SPI4 DEVID1 ICM20602_CS MODE3 1*MHZ 8*MHZ
|
|
SPIDEV ms5611_ext SPI4 DEVID2 MS5611_CS MODE3 20*MHZ 20*MHZ
|
|
SPIDEV ICM20948 SPI4 DEVID3 ICM20948_CS MODE3 1*MHZ 8*MHZ
|
|
|
|
#FRAM
|
|
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
|
|
#Spare CS Pins for external SPI devices (SPI6)
|
|
#SPIDEV EXTERNAL_DEV1 SPI6 DEVID1 SPI6_CS MODE0 2*MHZ 2*MHZ
|
|
#SPIDEV EXTERNAL_DEV2 SPI6 DEVID2 SPI6_CS2 MODE1 2*MHZ 2*MHZ
|
|
|
|
define HAL_CHIBIOS_ARCH_CUBE_RED 1
|
|
|
|
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
|
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
# fallback storage location is flash if no FRAM fitted
|
|
define STORAGE_FLASH_PAGE 22
|
|
|
|
# enable RAMTROM parameter storage
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
# Cube Red has an IMU header
|
|
define HAL_HAVE_IMU_HEATER 1
|
|
|
|
# enable FAT filesystem
|
|
define HAL_OS_FATFS_IO 1
|