Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
ardupilot/libraries/AP_HAL_ChibiOS/hwdef/SkystarsH7HD
History
Andy Piper 71e860feec AP_HAL_ChibiOS: make sure SkystarsH7HD has functioning VTX on Camera 1 by default 2022-10-04 16:50:08 +09:00
..
README.md AP_HAL_CHibiOS: add new hwdef target for SkystarsH7HD 2022-07-21 21:53:15 -07:00
SkystarsH7HD.jpg AP_HAL_CHibiOS: add new hwdef target for SkystarsH7HD 2022-07-21 21:53:15 -07:00
defaults.parm AP_HAL_CHibiOS: add new hwdef target for SkystarsH7HD 2022-07-21 21:53:15 -07:00
hwdef-bl.dat AP_HAL_ChibiOS: make sure SkystarsH7HD has functioning VTX on Camera 1 by default 2022-10-04 16:50:08 +09:00
hwdef.dat AP_HAL_ChibiOS: make sure SkystarsH7HD has functioning VTX on Camera 1 by default 2022-10-04 16:50:08 +09:00

README.md

Skystars H7 Flight Controller

The Skystars H7 is a flight controller produced by Skystars.

Features

  • STM32H743 microcontroller
  • BMI270 IMU
  • BMP280 barometer
  • AT7456E OSD
  • 6 UARTs
  • 9 PWM outputs

Pinout

Skystars H7HD Board

UART Mapping

The UARTs are marked RX and TX in the above pinouts. The RX pin is the receive pin for UARTn. The TX pin is the transmit pin for UARTn.

  • SERIAL0 -> USB
  • SERIAL1 -> UART1 (Telem1)
  • SERIAL2 -> UART2 (Telem2)
  • SERIAL3 -> UART3 (GPS)
  • SERIAL4 -> UART4
  • SERIAL5 -> not available
  • SERIAL6 -> UART6
  • SERIAL7 -> UART7

RC Input

RC input is configured on the R6 (UART6_RX) pin. It supports all RC protocols. For protocols requiring half-duplex serial to transmit telemetry (such as FPort) you should set BRD_ALT_CONFIG=1 and setup SERIAL6 as an RC input serial port, with half-duplex, pin-swap and inversion enabled.

OSD Support

The Skystars H7 supports OSD using OSD_TYPE 1 (MAX7456 driver).

PWM Output

The Skystars H7 supports up to 9 PWM outputs. The pads for motor output M1 to M8 on the two motor connectors, plus M9 for LED strip or another PWM output.

The PWM is in 5 groups:

  • PWM 1, 2 in group1
  • PWM 3, 4 in group2
  • PWM 5, 6 in group3
  • PWM 7, 8 in group4
  • PWM 9 in group5

Channels within the same group need to use the same output rate. If any channel in a group uses DShot then all channels in the group need to use DShot.

Battery Monitoring

The board has a builtin voltage and current sensor. The current sensor can read up to 130 Amps. The voltage sensor can handle up to 6S LiPo batteries.

The correct battery setting parameters are:

  • BATT_MONITOR 4
  • BATT_VOLT_PIN 10
  • BATT_CURR_PIN 11
  • BATT_VOLT_MULT 10.1
  • BATT_AMP_PERVLT 17.0

Compass

The Skystars H7 does not have a builtin compass, but you can attach an external compass using I2C on the SDA and SCL pads.

Loading Firmware

Initial firmware load can be done with DFU by plugging in USB with the bootloader button pressed. Then you should load the "with_bl.hex" firmware, using your favourite DFU loading tool.

Once the initial firmware is loaded you can update the firmware using any ArduPilot ground station software. Updates should be done with the *.apj firmware files.