mirror of https://github.com/ArduPilot/ardupilot
240 lines
15 KiB
Plaintext
240 lines
15 KiB
Plaintext
ArduCopter Release Notes:
|
|
------------------------------------------------------------------
|
|
ArduCopter 3.0.1-rc2 / 3.0.1 11-Jul-2013
|
|
Improvements over 3.0.1-rc1
|
|
1) Rate Roll, Pitch and Yaw I fix when we hit motor limits
|
|
2) pre-arm check changes:
|
|
a) double flash arming light when pre-arm checks fail
|
|
b) relax mag field checks to 35% min, 165% max of expected field
|
|
3) loiter and auto changes:
|
|
a) reduced Loiter speed to 5 m/s
|
|
b) reduced WP_ACCEL to 1 m/s/s (was 2.5 m/s/s)
|
|
c) rounding error fix in loiter controller
|
|
d) bug fix to stopping point calculation for RTL and loiter during missions
|
|
4) Stability Patch fix which was freezing Rate Taw I term and allowing uncommanded Yaw
|
|
------------------------------------------------------------------
|
|
ArduCopter 3.0.1-rc1 26-Jun-2013
|
|
Improvements over 3.0.0
|
|
1) bug fix to Fence checking position after GPS lock was lost
|
|
2) bug fix to LAND so that it does not attempt to maintain horizontal position without GPS lock
|
|
------------------------------------------------------------------
|
|
ArduCopter 3.0.0 / 3.0.0-rc6 16-Jun-2013
|
|
Improvements over 3.0.0-rc5
|
|
1) bug fix to Circle mode's start position (was moving to last loiter target)
|
|
2) WP_ACCEL parameter added to allow user to adjust acceleration during missions
|
|
3) loiter acceleration set to half of LOIT_SPEED parameter value (was hard-coded)
|
|
4) reduce AltHold P to 1.0 (was 2.0)
|
|
------------------------------------------------------------------
|
|
ArduCopter 3.0.0-rc5 04-Jun-2013
|
|
Improvements over 3.0.0-rc4
|
|
1) bug fix to LAND flight mode in which it could try to fly to mission's next waypoint location
|
|
2) bug fix to Circle mode to allow counter-clockwise rotation
|
|
3) bug fix to heading change in Loiter, RTL, Missions when pilot's throttle is zero
|
|
4) bug fix for mission sticking at take-off command when pilot's throttle is zero
|
|
5) bug fix for parameters not saving when new value is same as default value
|
|
6) reduce pre-arm board min voltage check to 4.3V (was 4.5V)
|
|
7) remove throttle controller's ability to limit lean angle in loiter, rtl, auto
|
|
------------------------------------------------------------------
|
|
ArduCopter 3.0.0-rc4 02-Jun-2013
|
|
Improvements over 3.0.0-rc3
|
|
1) loiter improvements:
|
|
i) repositioning enhanced with feed forward
|
|
ii) use tan to convert desired accel to lean angle
|
|
2) stability patch improvements for high powered copters or those with roll-pitch rate gains set too high
|
|
3) auto mode vertical speed fix (it was not reaching the desired speeds)
|
|
4) alt hold smoothed by filtering feed forward input
|
|
5) circle mode fix to initial position and smoother initialisation
|
|
6) RTL returns to initial yaw heading before descending
|
|
7) safe features:
|
|
i) check for gps lock when entering failsafe
|
|
ii) pre-arm check for mag field lenght
|
|
iii) pre-arm check for board voltage between 4.5v ~ 5.8V
|
|
iv) beep twice during arming
|
|
v) GPS failsafe enabled by default (will LAND if loses GPS in Loiter, AUTO, Guided modes)
|
|
vi) bug fix for alt-hold mode spinning motors before pilot has raised throttle
|
|
8) bug fixes:
|
|
i) fixed position mode so it responding to pilot input
|
|
ii) baro cli test
|
|
iii) moved cli motor test to test sub menu and minor change to throttle output
|
|
iv) guided mode yaw control fix
|
|
------------------------------------------------------------------
|
|
ArduCopter 3.0.0-rc3 22-May-2013
|
|
Improvements over 3.0.0-rc2
|
|
1) bug fix for dataflash erasing unnecessarily
|
|
2) smoother transition to waypoints, loiter:
|
|
intermediate point's speed initialised from copter's current speed
|
|
3) Ch8 auxiliary function switch (same features as Ch7)
|
|
4) safety checks:
|
|
Warning to GCS of reason for pre-arm check failure
|
|
ARMING_CHECK parameter added to allow disabling pre-arm checks
|
|
Added compass health and offset check to pre-arm check
|
|
compassmot procedure displays interference as percentage of total mag field
|
|
5) WPNAV dataflash message combined into NTUN message
|
|
6) allow TriCopters to use ESC calibration
|
|
------------------------------------------------------------------
|
|
ArduCopter 3.0.0-rc2 13-May-2013
|
|
Improvements over 3.0.0-rc1:
|
|
1) smoother transition to waypoints, loiter:
|
|
reduced loiter max acceleration to smooth waypoints
|
|
bug fix to uninitialised roll/pitch when entering RTL, AUTO, LOITER
|
|
2) fast waypoints - copter does not stop at waypoints unless delay is specified
|
|
3) WPNAV_LOIT_SPEED added to allow faster/slower loiter repositioning
|
|
4) removed speed limits on auto missions
|
|
5) enhance LAND mission command takes lat/lon coordinates
|
|
6) bug fix for RTL not pointing home sometimes
|
|
7) centrifugal correction disabled when copter is disarmed to stop HUD moving
|
|
8) centrifugal correction disabled when sat count less than 6 (AHRS_GPS_MINSATS)
|
|
9) compass calibration reliability improvements when run from mission planner
|
|
10) bug fix to allow compassmot to be run from mission planner terminal screen
|
|
11) add support for H-quad frame
|
|
12) add COMPASS_ORIENT parameter to support external compass in any orientation
|
|
------------------------------------------------------------------
|
|
ArduCopter 3.0.0-rc1 01-May-2013
|
|
Improvements over 2.9.1b:
|
|
1) Inertial navigation for X & Y axis (Randy/Leonard/Jonathan)
|
|
2) 3D waypoint navigation library (Leonard/Randy)
|
|
WPNAV_SPEED, WPNAV_SPEED_UP, WPNAV_SPEED_DN control target speeds during missions and RTL
|
|
WP_YAW_BEHAVIOR to allow disabling yaw during missions and RTL
|
|
3) PX4 support (some features still not available) (Tridge/Pat/PX4Dev Team)
|
|
4) Safety improvements:
|
|
Tin-can shaped fence (set FENCE_ENABLED to 1 and copter will RTL if alt > 150m or horizontal distance from home > 300m) (Randy/Tridge/Leonard)
|
|
GCS failsafe (set FS_GCS_ENABLED to 1 and if you are using a tablet to fly your copter it will RTL and return control to the radio 3 seconds after losing telemetry) (Randy)
|
|
pre-arm checks to ensure accelerometer and radio calibration has been performed before arming (Randy)
|
|
5) motor interference compensation for compass (Jonathan/Randy)
|
|
6) Circle mode improvements:
|
|
set CIRCLE_RADIUS to zero to do panorama shots in circle mode (copter does not move in a circle but instead slowly rotates)
|
|
CIRCLE_RATE parameter allows controlling direction and speed of rotation in CIRCLE mode and LOITER_TURNS (can also be adjusted in flight from CH6 knob)
|
|
7) SONAR_GAIN parameter add to allow reducing the response to objects sensed by sonar (Randy)
|
|
8) support for trapezoidal quads (aka V shaped or FPV quads) (Leonard/Craig)
|
|
9) performance improvements to dataflash logging (Tridge)
|
|
10) bug-fix to analog read which could cause bad sonar reads when using voltage or current monitor (Tridge)
|
|
11) bug-fix to motors going to minimum when throttle is low while switching into Loiter, AUTO, RTL, ALT_HOLD (Jason/Randy)
|
|
12) bug-fix for auto disarm sometimes disarming shortly after arming (Jason/SirAlex)
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9.1b 30-Feb-2013
|
|
Improvements over 2.9.1:
|
|
1) reduce INS_MPU6K_FILTER to 20hz
|
|
2) reduce InertialNav Z-axis time constant to 5 (was 7)
|
|
3) increased max InertialNav accel correction to 3 m/s (was 1m/s)
|
|
4) bug fix for alt_hold being passed as int16_t to get_throttle_althold_with_slew
|
|
5) bug fix for throttle after acro flip (was being kept at min throttle if pilot switched out of ACRO mode while inverted)
|
|
6) reduce yaw_rate P default to 0.20 (was 0.25)
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9.1 & 2.9.1-rc2 01-Feb-2013
|
|
Improvements over 2.9.1-rc1:
|
|
1) small corretion to use of THR_MID to scale lower end of manual throttle between THR_MIN and 500 instead of 0 and 500
|
|
2) bug fix for longitude scaling being incorrectly calculated using Next Waypoint instead of home which could lead to scaling being 1
|
|
3) ESC calibration change to set update rate to ESCs to 50hz to allow simonk ESC to be calibrated
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9.1-rc1 31-Jan-2013
|
|
Improvements over 2.9:
|
|
1) THR_MID parameter added to allow users to adjust the manual throttle so that vehicle hovers at about mid stick
|
|
2) bug fix for autotrim - roll axis was backwards
|
|
3) bug fix to set sonar_alt_health to zero when sonar is disabled
|
|
4) capture level roll and pitch trims as part of accel calibration
|
|
5) bug fix to ppm encoder false positives
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9 & 2.9-rc5 14-Jan-2013
|
|
Improvements over 2.9-rc4:
|
|
1) add constraint to loiter commanded roll and pitch angles
|
|
2) relax altitude requirement for take-off command to complete
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9-rc4 12-Jan-2013
|
|
Improvements over 2.9-rc3:
|
|
1) Smoother transition between manual and auto flight modes (Leonard)
|
|
2) bug fix for LAND not actually landing when initiated from failsafe (Randy/Craig)
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9-rc3 11-Jan-2013
|
|
Improvements over 2.9-rc2:
|
|
1) alt hold with sonar improvements - now on by default (Leonard/Randy)
|
|
2) performance and memory useage improvements (Tridge/Randy)
|
|
3) increase APM1 baro pressure read from 5hz to 8.3hz to improve alt hold (Randy)
|
|
4) bug fix: altitude error reported to GCS (Randy)
|
|
5) limit inertial nav's max accel offset correction to 100cm/s/s to speed up recovery after hard impacts (Randy)_
|
|
6) moved rate controllers to run after ins read (Tridge/Randy)
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9-rc2 31-Dec-2012
|
|
Improvements over 2.9-rc1:
|
|
1) increased throttle rate gains from 1.0 to 6.0
|
|
2) APM1 fix so it works with inertial nav (5hz update rate of baro was beyond the tolerance set in the inav library)
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.9-rc1 23-Dec-2012
|
|
Improvements over 2.8.1:
|
|
1) altitude hold improvements:
|
|
a)inertial navigation for vertical axis [Randy/Jonathan/Leonard/Jason]
|
|
b)accel based throttle controller [Leonard/Randy]
|
|
c)accelerometer calibration routine updated to use gauss-newton method [Randy/Tridge/Rolfe Schmidt]
|
|
d)parameters to control climb rate:
|
|
AUTO_VELZ_MIN, AUTO_VELZ_MAX - allows you to control the maximum climb and descent rates of the autopilot (in cm/s)
|
|
PILOT_VELZ_MAX - allows you to control the maximum climb/descent rate when in alt hold or loiter (in cm/s)
|
|
2) landing improvements [Leonard/Randy]
|
|
LAND_SPEED - allows you to set the landing speed in cm/s
|
|
3) camera related improvements:
|
|
a) AP_Relay enabled for APM2 and integrated with AP_Camera [Sandro Benigno]
|
|
b) camera trigger with channel 7 switch or DO_DIGICAM_CONTROL mission command [Randy]
|
|
c) allow yaw override by pilot or with CONDITIONAL_YAW command during missions [Randy]
|
|
YAW_OVR_BEHAVE - Controls when autopilot takes back normal control of yaw after pilot overrides (0=after next wp, 1=never)
|
|
4) trad heli improvements [Rob]
|
|
a) code tested and brought back into the fold (2.8.1 was never released for trad helis)
|
|
b) enabled rate controller (previously only used angle controllers)
|
|
c) fix to rotor speed controllers - now operates by switching off channel 8
|
|
d) allow wider collective pitch range in acro and alt hold modes vs stabilize mode
|
|
e) removed angle boost function because it created more problems than it solved
|
|
f) bug fix to allow collective pitch to use the entire range of servos
|
|
5) mediatek gps driver improvements [Craig]
|
|
a) added support for 1.9 firmware
|
|
b) bug fix to start-up routine so sbas can be enabled
|
|
6) failsafe improvements (both throttle and battery) [Randy/Craig/John Arne Birkeland]
|
|
a) RTL will not trigger if your throttle is zero - reduces risk of accidentally invoking RTL if you switch off your receiver before disarming
|
|
b) failsafe triggered in unlikely case of a PPM encoder failure
|
|
c) bug fix to resolve motors momentarily reducing to zero after failsafe is triggered
|
|
7) mpu6k filtering made configurable and default changed to 42hz for copters [Leonard/Tridge]
|
|
8) support ppm sum for transmitters with as few as 5 channels [Randy/John Arne Birkeland]
|
|
9) acro trainer - copter will return to be generally upright if you release the sticks in acro mode [Leonard]
|
|
ACRO_BAL_ROLL, ACRO_BAL_PITCH - controls rate at which roll returns to level
|
|
ACRO_TRAINER - 1 to enable the auto-bring-upright feature
|
|
10) other changes and bug fixes:
|
|
a) allow >45 degrees when in stabilize mode by adding lines like below to APM_Config (compile time option only) [Jason]
|
|
#define MAX_INPUT_ROLL_ANGLE 6000 // 60 degrees
|
|
#define MAX_INPUT_PITCH_ANGLE 6000 // 60 degrees
|
|
b) bug fix to stop RTL from ever climbing to an unreasonable height (i.e. >80m) [Jason]
|
|
c) event and state logging [Jason]
|
|
d) allow cli to be used over telemetry link [Tridge]
|
|
e) bug fix to allow compass accumulate to run when we have spare cpu cycles [Randy]
|
|
f) bug fix so do_set_servo command works [Randy]
|
|
g) bug fix to PID controller's so they don't calculate crazy D term on the first call [Tridge]
|
|
h) bug fix to initialise navigation parameter to resolve twitch when entering some navigation modes [Jason]
|
|
i) performance improvement to copter leds - use DigitalFastWrite and DigitalFastRead instead of native arduino functions [Randy]
|
|
j) removed unused stab_d from roll and pitch controller [Jason]
|
|
k) bug fix for guided mode not reaching target altitude if it reaches horizontal target first [Randy]
|
|
l) code clean-up, parameter documentation improvements [Randy/Jason/Rob/others]
|
|
|
|
------------------------------------------------------------------
|
|
ArduCopter 2.8.1 22-Oct-2012
|
|
Improvements over 2.8:
|
|
- 430 bytes of RAM freed up to resolve APM1 level issue and reduce chance of memory corruption on both APM1 and APM2
|
|
|
|
Improvements over 2.7.3:
|
|
- Improved ACRO mode (Leonard Hall)
|
|
- Improved stability patch to reduce "climb-on-yaw" problem (Leonard, Rob Lefebvre, Randy)
|
|
- Rate controller targets moved to body frames (yaw control now works properly when copter is inverted) (Leonard/Randy)
|
|
- Less bouncy Stabilize yaw control (Leonard)
|
|
- OpticalFlow sensor support for APM2.5 (Randy)
|
|
- DMP works again by adding "#define DMP_ENABLED ENABLED" to APM_Config.h You can also log DMP vs DCM to the dataflash by adding "#define SECONDARY_DMP_ENABLED ENABLED" (Randy)
|
|
- Watch dog added to shutdown motors if main loop feezes for 2 seconds (Randy)
|
|
- Thrust curve added to linearize pwm->thrust. Removes deadzone found above 90% throttle in most ESC/motors (Randy)
|
|
- More timing improvements (main loop is now tied to MPU6000s interrupt) (Randy)
|
|
- GPS NMEA bug fix (Alexey Kozin)
|
|
- Logging improvements (log I terms, dump all settings at head of dataflash log) (Jason)
|
|
|
|
Bug Fixes / Parameter changes:
|
|
- fixed skipping of last waypoint (Jason)
|
|
- resolved twitching when no GPS attached (Tridge)
|
|
- fixed loss of altitude if alt hold is engaged before first GPS lock (Randy/Jason)
|
|
- moved Roll-Pitch I terms from Stabilize controllers to Rate controllers
|
|
- TILT_COMPENSATION param tuned for TradHeli (Rob)
|
|
|
|
Code Cleanup:
|
|
- HAL changes for platform portability (Pat Hickey)
|
|
- Removed INSTANT_PWM (Randy)
|
|
------------------------------------------------------------------ |